User Manual
Table Of Contents
- Contents
- ENGLISH
- Introduction
- Specifications
- Before you begin
- Tools needed
- Package contents
- Installation instructions
- STEP 1 - Prepare your TV
- STEP 2 - Adjust the soundbar mount arms
- STEP 3 - Assemble your soundbar mount
- STEP 4 - Determine the TV screw diameter
- STEP 5 - Determine whether your TV has a flat, irregular, or obstructed back
- STEP 6 - Install the soundbar mount on your TV
- STEP 7 - Install your soundbar to the arms
- STEP 7A - Back-mounted key hole slots
- STEP 7B - Back-mounted threaded inserts
- STEP 7C - Bottom-mounted threaded inserts
- STEP 8 - Hang your TV
- STEP 9 - Adjust the soundbar height (optional)
- STEP 10 - Adjust the soundbar depth (optional)
- LIFETIME LIMITED WARRANTY
- ESPAÑOL
- Introducción
- Especificaciones
- Antes de comenzar
- Herramientas requeridas
- Contenido del paquete
- Instrucciones de instalación
- PASO 1 - Prepare su televisor
- PASO 2: Ajuste los brazos de montaje de la barra de sonido
- PASO 3 - Ensamble el montaje de la barra de sonido
- PASO 4 - Determine el diámetro del tornillo para el televisor
- PASO 5 - Determine si su televisor tiene una parte posterior plana, irregular u obstruida.
- PASO 6 - Instalación del montaje de la barra de sonido en su televisor
- PASO 7 - Instalación de su barra de sonido a los brazos
- PASO 7A: Ranuras de bocallave para el montaje posterior
- PASO 7B: Insertos con rosca de la parte posterior
- PASO 7C - Insertos con rosca de la parte inferior
- PASO 8 - Sujete su televisor
- PASO 9: Ajuste de la altura de la barra de sonido (opcional)
- PASO 10 - Ajuste de la profundidad de la barra de sonido (opcional)
- GARANTÍA LIMITADA DE POR VIDA
11
RF-SBM102
STEP 6 - Install the soundbar mount on your TV
CAUTION: To offset the shift in height of your TV bracket caused by the soundbar bracket (01), you must use the spacers (16) in
the top hole locations and the washers (17) in the bottom hole locations.
1 If your TV has a flat back, place the 16mm spacers (16) over your TV’s top mounting holes and the interface
washers (17) over the bottom mounting holes.
OR
If your TV has an irregular or obstructed back, place your TV mount spacers over your TV’s mounting holes. Then place
the 16 mm spacers (16) over the spacers on the top mounting holes and the interface washers (17) over the spacer on
the bottom mounting holes.
You’ll need
TV with a flat back
TV mount spacers
TV mount spacers
TV with an irregular or obstructed back
Phillips screwdriver
05 M4 × 30 mm
screw (4)
06 M4 × 50 mm
screw (4)
One type of the following screws (4)
07 M6 × 30 mm
screw (4)
08 M6 × 50 mm
screw (4)
09 M8 × 30 mm
screw (4)
10 M8 × 40 mm
screw (4)
11 M8 × 50 mm
screw (4)
12 M8 × 65 mm
screw (4)
One type of the following
washers (4)
13 M4 washer
(4)
14 M8/M6
washer (4)
16 16 mm
spacer (2)
17 Interface
washer (2)