RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 1 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Safety information and specifications .................................2 Tools needed.................................................................................3 Parts..................................................................................................4 Assembly instructions................................................................
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 2 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Maximum TV weight: 60 lbs. (27.2 kg) CAUTION: Do not use this product for Screen size: 26" to 40" diagonal any purpose not explicitly specified by Overall dimensions (W × H ): Rocketfish. 15.8 × 17.8 × 2.8 in. (40.1 × 45.2 × 7.1 cm) Improper installation may cause property damage or personal injury.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 3 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Tools needed You will need the following tools to assemble your new TV wall mount: Edge-to-edge stud finder Phillips screwdriver Pencil Level Socket wrench with 1/2" (13 mm) socket or adjustable wrench Drill 7/32" (5.5 mm) wood drill bit for wood stud wall OR 3/8" (10 mm) masonry drill bit (concrete only) Measuring tape Tape Hammer Need help? Call 1-800-620-2790 (U.S.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 4 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Parts Package contents: parts Make sure that you have all the parts necessary to assemble your new TV wall mount: A Arm assembly (1) B Right vertical TV bracket (1) C Left vertical TV bracket (1) D Horizontal TV bracket (2) F Cable cover (1) E Template (1) Hardware 4 Need help? Call 1-800-620-2790 (U.S.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 5 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Package contents: hardware Make sure that you have all the hardware necessary to assemble your new TV wall mount: TV Hardware Bag Label G H Hardware M4 × 12 mm screw M4 × 35 mm screw Qty. Label Hardware Qty.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 6 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Assembly instructions STEP 1 Determine whether your TV has a flat back or an irregular or obstructed back 1 2 3 4 5 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 7 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 2 Select screws, washers, and spacers 1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 8 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 3 Install the vertical TV brackets - Option 1: Installing for a TV with a flat back 1 2 3 Center the brackets vertically on the back of your TV, then align the holes on the right vertical TV bracket (B) and left vertical TV bracket (C) with the screw holes on the back of your TV. The brackets are marked “R” for the right bracket and “L” for the left bracket. Make sure the brackets are level.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 9 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 3 Install the vertical TV brackets - Option 2: Installing for an irregular or obstructed back 1 2 3 4 Place the spacers (K) into the screw holes on the back of your TV. Align the holes on the right vertical TV bracket (B) and left vertical TV bracket (C) with the spacers on the back of your TV. The brackets are marked “R” for the right bracket and “L” for the left bracket.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 10 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 4 Install the horizontal TV brackets 1 2 Slide the horizontal brackets (D) through the metal guides on the vertical TV brackets until they are centered. Secure the horizontal TV brackets to the vertical TV brackets using the 8-32 x 9/16" Phillips head screws (V). Tighten the screws until they are snug, but do not over tighten.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 11 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 5 Determine the wall-mount location Note: • For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder • Your TV should be high enough so your eyes are level with the middle of the screen. Normally, 40 to 60 inches from the ground.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 12 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 6 -Option 1 - Install the wall plate to a wood stud wall Note: Drywall covering the wall must not exceed 5/8" (16 mm). 1 2 3 4 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder and mark the center. Align the wall plate template (E) at the height you determined in the previous step and make sure that it is level.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 13 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 6 - Option 2: Installing on a solid concrete or concrete block wall CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount the arm assembly directly onto the concrete surface. 1 2 3 4 Align the wall plate template (E) at the height you determined in the previous step and make sure that it is level.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 14 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 7 Attach the arm assembly 1 2 3 Hang the TV, with the brackets attached, on the upper lip of the arm assembly (A), as shown below. Lower the bottom edge of the of the horizontal TV bracket (D) to the bottom of the arm assembly (A). Secure the arm assembly (A) with the 8-32 x 3/8” cap screw (W) using a phillips screw driver. Do not overtighten the screw.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 15 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 8 Adjusting the tension and leveling the arm assembly 1 2 3 4 5 Loosen the two screws on the arm assembly using the 5/32" hex key (Y), then using a level, adjust the arm assembly ± 6° either clockwise or counter-clockwise to level it. Using a 3/16” hex key (Z), or your hand, loosen the knob on the right side of the arm assembly, then adjust the tilt ± 11°.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 16 Tuesday, July 9, 2013 8:02 AM RF-TVMFM02V2 TV Wall Mount Step 9 Managing the cables • Use the cable cover (F) to bundle the cables together, then attach to the arm assembly (A). OR • Use cable ties (X) to secure the cables to the arm assembly (A). Note: You may have to readjust the forward or backward tilt after you bundle the cables. You’ll need X (5) F (1) For customer service, call: 1-800-620-2790 (U.S.
RF-TVMFM02V2_13-0600_MAN_V4_ENG - GIFs.fm Page 17 Tuesday, July 9, 2013 8:02 AM www.rocketfishproducts.com 1-800-620-2790 (U.S. and Canada) or 01-800-926-3010 (Mexico) Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN 55423-3645 USA © 2013 BBY Solutions, Inc. All rights reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are trademarks of their respective owners.