Source Unit Less than 18" INPUT FRONT REAR I I I I. • I I_--- + NEG POS Battery ~~--~~~< Connect to chassis ground of vehicle *Keep grounds as short as possible. For Motorsport and Boat applications, the ground wire should go directly to the negative battery terminal. Optional Accessory PLC2 (T400X2ad!T500X1bd) Lh_CAUTION Be sure to connect speakers and Punch Level Control - PLC {if equipped) after amplifier output clip adjustment.
Amplifier Clip Indicator Setup • Input Clip Indicator Setup Be sure to disconnect all speakers from the amplifier. Insert test tone or music CD to play for setup. &CAUTION Failure to comply may cause damage to connected components and/or amplifier. ........-.... Adjust the Bass & Treble levels on the source unit to flat. Note: Use the 40Hz @OdB tone (Track 5) for mono amplifier applications or the 1kHz@ OdB tone (Track 7) for multi-channel amplifier applications.
AMPLIFIERS T400X2ad T400X4ad T500X1br Installation & Operation
:WLJPÄJH[PVUZ Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of car audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
+LZPNU -LH[\YLZ +LZPNU -LH[\YLZ Intput Clip Indicator Output Clip Indicator The input clip indicator works in conjunction with the audio source volume knob, illuminating red when audio source reaches it’s clipping point. The output clip indicator works in conjunction with the input level knob, illuminating to appropriate color depending on the audio content used for the setup. Input Level Knob The input level control is used to match the output of the audio source.
0UZ[HSSH[PVU 0UZ[HSSH[PVU Contents s Power Amplifier s RCA to 4-pin Molex Input Connector(s) s 16 AWG 4-pin Molex Speaker Connector(s) - (T400X2ad & T4004ad) s 10 AWG Speaker Connector (T500X1br) s Power Connector s Quick Setup Guide s Installation & Operation Manual s Operation CD- (Test Tones & Installation Manual) The following is a list of tools needed for installation: s Hand held drill w/assorted bits s Assorted connectors s Volt/Ohm Meter s Wire strippers s Wire crimpers s Adequate Length—Red Pow
0UZ[HSSH[PVU 0UZ[HSSH[PVU 2-Channel (Stereo) 2-Channel (Mono) T400X2ad T400X2ad ** For high level input; cut supplied input harnesses then use the wire harness color codes below. ** For high level input; cut supplied input harnesses then use the wire harness color codes below. illus.-2.
0UZ[HSSH[PVU 0UZ[HSSH[PVU 4-Channel (Stereo) 4-Channel (2ch Stereo & 1ch Mono-Bridged) T400X4ad T400X4ad ** For high level input; cut supplied input harnesses then use the wire harness color codes below. illus.-2.3 10 ** For high level input; cut supplied input harnesses then use the wire harness color codes below.
0UZ[HSSH[PVU 0UZ[HSSH[PVU 4-Channel (2ch Mono-Bridged) Mono Wiring T400X4ad T500X1br ** For high level input; cut supplied input harnesses then use the wire harness color codes below. ** For high level input; cut supplied input harnesses then use the wire harness color codes below. illus.-2.
6WLYH[PVU 6WLYH[PVU illus.-3.1 Input Clip Indicator Setup Step 1. Step 6. Be sure to disconnect all speakers from the amplifier. Decrease the source unit volume slightly until the light turns completely off. This establishes your maximum source unit volume for adjusting the Output Clip Indicator. illus.-3.6 Failure to comply may cause damage to connected components and/or amplifier. Step 2. Turn on the source unit with volume set to zero. Volume illus.-4.1 illus.-4.
;YV\ISLZOVV[PUN Troubleshooting NOTE: If you are having problems after installation follow the Troubleshooting procedures below. Check Amplifier for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue. 1. Check in-line fuse on battery positive cable. Replace if necessary. 2. Check fuse(s) on amplifier. Replace if necessary. >HYYHU[` Check Amplifier if you experience excess Engine Noise. Length of Warranty 1.
Installation assistance available at: www.rockfordfosgate.com/rftech 033114 1230-58566-01 English Printed In China 3OUTH 2OCKFORD $RIVE s 4EMPE !RIZONA 5NITED 3TATES Direct s 4OLL &REE R O C K F O R D F O S G AT E .
r-F.=:::::::::::::::::::CERTIFICATE OF PERFORMANCE VERIFICATION :=-- =::::=-~Tl~ !III ,, II I I Total Power Total RMS Power @ 1% THO 546 watts ALL Rockford Fosgate amplifiers are designed, developed, manufactured and tested in accordance w ith the CEA-2006 amplifier rating requirements. All tests conducted at 14.4Vdc , Min. Impedance, 1kHz(ab/ad) or 100Hz (bd) unless otherwise stated. ©2013 Rockford Corporation. All Rights Reserved.
Are You Engineered to Rock? Get a One-Year Extended Warranty when you use a matching Rockford Fosgate Amplifier Installation kit with your Amplifier! We want you to get the performance and reliability that made Rockford Fosgate Amplifiers famous. Using poorquality under-spec wiring is a guaranteed way to get less than you paid for from your system.
Installation assistance available at: www.rockfordfosgate.com/rftech SPEAKERS • TMS69 1230-62234-01-B Printed in China TMS57 030818 Serial Number: Date of Purchase: 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications TMS57 TMS69 5x7 (127 x 178) 6x9 (152 x 229) 2-Way 2-Way 4Ω 4Ω Frequency Response (Hz) 63-20kHz 56-20kHz Voice Coil Diameter - inch (mm) 1.4 (35.6) 1.4 (35.6) 100/200 100/200 Fs - Free Air Resonance (Hz) 80Hz 75 Qts 1.17 1.63 Vas - cu. ft. (Liter) 0.354 (9.9) 0.593 (16.8) Sensitivity (1W/1M) 89dB 89dB Sensitivity (2.83V/1M) 92dB 92dB Xmax - inch (mm) 0.12 (3) 0.12 (3) 4.3 x 5 (185 x 127) 8.6 x 5.6 (218 x 147) Mounting Depth 2.2 (56) 2.
Specifications TMS57 7.8” (199mm) 4.7” (119mm) 5.4” (138mm) 4.8” (121mm) 2.6” (66mm) 2.2” (56mm) 4.3” (185mm) 5” (127mm) TMS69 9.2” (234mm) 6.5” (165mm) 6.4” (163mm) 4.7” (120mm) 3.2” (81mm) 3.2” (81mm) 2.8” (70mm) 8.6” (218mm) 2.8” (70mm) 5.6” (147mm) illus.-1.
Installation Contents Example of standard installation • (1) Pair TMS Speakers • (8) Socket head screws Installation Considerations Before beginning any installation, follow these simple rules: 1. Be sure to carefully read and understand the instructions before attempting to install these speakers. Cutout Hole 2. For safety, disconnect the negative lead from the battery prior to beginning the installation. 3. For easier assembly, we suggest you run all wires prior to mounting your speakers in place.
Français Considérations Concernant L’installation Consideraciones para la instalación Avant de commencer l’installation, suivez les règles ci-dessous: Antes de comenzar cualquier instalación, siga estas simples normas: 1. Veillez à bien lire et comprendre les instructions avant d’essayer d’installer les haut-parleurs. 1. 1. Asegúrese de leer cuidadosamente y de entender las instrucciones antes de tratar de instalar estos altavoces. 2.
Deutsch Einbauüberlegungen Befolgen Sie vor dem Einbau diese einfachen Regeln: 1. 1. Lesen Sie die Anleitung sorgfältig, bevor Sie versuchen diese Lautsprecher einzubauen. 2. Entfernen Sie vor dem Einbau aus Sicherheitsgründen das negative Kabel von der Batterie. 3. Um die Montage zu erleichtern, empfehlen wir alle Kabel vor der Befestigung Ihrer Lautsprecher zu verlegen. 4. Verwenden Sie nur Qualitätsstecker, um einen zuverlässigen Einbau zu gewährleisten und Signal- und Stromverlust zu minimieren. 5.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years Source Units – 2 Years All other products – 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
2014 & UP HARLEY-DAVIDSON® SPEAKERS TMS65 Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications Model TMS65 Nominal Diameter - inch (mm) 6.5 (165) Description 2-Way Nominal Impedance (Ohms) 4Ω Frequency Response (Hz) 65-20kHz Voice Coil Diameter - inch (mm) 1.4 (35.6) Power Handling - Watts (RMS/Peak) 75/150 Fs - Free Air Resonance (Hz) 86.5 Qts 0.52 Vas - cu. ft. (Liter) 0.198 (5.6) Sensitivity (1W/1M) 91dB Sensitivity (2.83V/1M) 94dB Xmax - inch (mm) 0.19 (3.0) Mounting Diameter 5.0 (128) Mounting Depth 2.
Specifications TMS65 90° 45° 6.2” Dia. (157mm) 2.6” (67mm) 2.3” (59mm) 5.6” Dia. (142mm) 2014 & Up Street Guide® Grilles Included 2015 & Up Road Glide® Grilles Included 2014 & Up Tour Pak Grilles Included illus.-1.
Installation Installation Considerations Contents • (1) Pair of 2-Way Speakers • (1) Pair of 2015 & Up Road Glide Grilles • (1) Pair of 2014 & Up Tour-Pak Grilles • Installation & Operation Manual • (1) Pair of 2014 & Up Street Glide Grilles Installation Tools The following is a list of suggested tools needed for installation: • Plastic Trim Panel Pry Tool • Allen Wrench - 3/16”, 5/32” • Torx - T10, T25, T27 This section focuses on some considerations for installing your motorcycle replacement speakers
Installation Front Speakers for Ultra Classic®, Electra Glide®, Street Glide® and Tri Glide® models. You will need to disconnect the harness from the headlight to completely take the fairing off of the motorcycle. Step 1 - Fairing Removal To begin with, remove the top screws below the windshield to remove the windshield. Step 2 - Speaker & Pod Removal After the fairing is removed, this will provide access for the speaker pods that need to be removed so the speakers can be replaced.
Installation Remove the top two bolts with a allen head screwdriver or ratchet. Unplug the module and set it aside. After the top two bolts are removed, remove the three bolts that are under the radio area. Next, remove the last three screws that hold the pod to the fairing. Remove the fairing and set aside for the speaker removal. If your bike is equipped with the optional communication setup, you will need to remove the module to access mounting bolts.
Installation Using a screwdriver, remove the speaker grille that is attached to the fairing. With the pod on a bench, unscrew the mounting screws to remove the factory speaker from the factory pod. Step 3 - Speaker Installation Prior to installing the speaker to the pod, there are alignment pins on the pod that the speaker needs to line up to ensure proper fit. Take the new Rockford speaker and slide the wire connectors over the terminals.
Installation Attach the new Rockford grille to the inside of the fairing. NOTE: The speaker grilles are side specific and have a notch in one of the mounting holes as an indicator. The notch is faced towards the middle of the bike. Reattach the pod with the factory hardware and reinstall any wire harnesses that were removed for the pod removal. Install the outer fairing to the motorcycle after speaker pods and wiring is secured. Front Speakers for Road Glide® and Road Glide Ultra® models.
Installation Unplug the terminals to disconnect the speaker. Secure the speaker to the pod using the factory hardware. Step 2 - Speaker & Grille Installation NOTE: Do not overtighten screws. Doing so can strip the threads on the plastic pod. Take the new Rockford speaker and slide the wire connectors over the terminals. NOTE: The smaller terminal is the positive (+) and the larger terminal is the negative (-).
Installation Rear Speakers for Tour-Pak models. Step 1 - Rear Speaker Removal Unscrew the speaker grilles from the rear pods and remove factory speaker. Unplug the terminals to disconnect the speaker. Step 2 - Rear Speaker Installation Connect the speakers by sliding the speaker wire connector over the speaker terminals NOTE: The smaller terminal is the positive (+) and the larger terminal is the negative (-). Insert the new Rockford speaker into the speaker pod and secure with mounting screws.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years Source Units – 1 Year All other products – 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance availible at: 051816 1230-60823-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
