AMPLIFIERS P300X1 P300X2 P400X1 P400X2 P400X4 P500X1BD P500X2 P600X4 P1000X1BD P1000X2 P1000X5 Installation & Operation
20k >85dB >105dB >50dB >55dB >500 20k >85dB >105dB >50dB >55dB >500 S/N Ratio CEA 2006 S/N Ratio @ Rated Power Channel Separation Common Mode Rejection Ratio Damping Factor Dimensions (LxWxH) (33.7cm x 19.7cm x 6.1 cm) 13.3” x 7.8” x 2.4” >500 >55dB >50dB >105dB >85dB 20k 150mV-12V <1.0% @ 4 ohms <1.0% @ 2 ohms 80A 20Hz-20kHz 9-16VDC Variable 0 -+14dB @ 12.5kHz and 0-+18dB @ 45Hz Variable 50Hz250Hz (38.2cm x 19.7cm x 6.1 cm) 15” x 7.8” x 2.
Design Features Design Features Crossover Switch Output Clip Indicator Selectable switch for High-Pass (HP) or All Pass (AP) or Low-Pass (LP) The output clip indicator works in conjunction with the input level knob, illuminating to appropriate color depending on the audio content used for the setup. Power/Protect LED Punch EQ A Gyrator based Punch EQ that eliminates frequency shift with boost. This works along with the crossover switch on the amplifier.
Installation Installation Contents • Punch Amplifier • Installation & Operation Manual • Mounting Hardware • Operation CD- (Test Tones & Installation Manual) • Allen Wrench Installation Considerations The following is a list of tools needed for installation: • Fuse-holder and fuse. (See specifications for fuse rating) • Wire strippers • Wire crimpers • Wire cutters • #2 Phillips screwdriver 7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.
Installation Installation 2-Channel (Stereo) 2-Channel (Mono) P300X2, P400X2, P500X2, P1000X2 P300X2, P400X2, P500X2, P1000X2 PASS-THRU Connect to inputs of 2nd amplifier PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install *Installation option for multi-amp install LEFT RIGHT PASS-THRU REMOTE PUNCH LEVEL INPUT GND LEFT RIGHT RIGHT LEFT INPUT CLIP illus.-2.
Installation Installation 4-Channel (Stereo) 4-Channel (2ch Stereo & 1ch Mono-Bridged) P400X4, P600X4 P400X4, P600X4 PASS-THRU Connect to inputs of 2nd amplifier PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install *Installation option for multi-amp install FRONT REAR LEFT RIGHT REMOTE PUNCH LEVEL FRONT LEFT RIGHT REM GND REAR LEFT illus.-2.
Installation Installation 4-Channel (2ch Mono-Bridged) 3-Channel (2ch bridged & 1ch Mono) P1000X5 P400X4, P600X4 PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install FRONT REAR LEFT RIGHT REMOTE PUNCH LEVEL FRONT LEFT RIGHT REM GND REAR SUB LEFT RIGHT LEFT RIGHT REMOTE PUNCH LEVEL B+ REM RIGHT BRIDGED SPEAKERS INPUT LEFT RIGHT BRIDGED INPUT CLIP FRONT PASS-THRU REAR illus.-2.
Installation Installation 5-Channel (4ch Stereo & 1ch Mono) Parallel Wiring (Full Range Capable) P1000X5 P300X1, P400X1 PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install REAR SUB LEFT RIGHT LEFT RIGHT REMOTE PUNCH LEVEL INPUT REM GND LEFT RIGHT B+ RIGHT BRIDGED LEFT RIGHT A B BRIDGED SPEAKERS INPUT CLIP FRONT REAR SUB PLC-OUT LEFT REMOTE PUNCH LEVEL A B SPEAKERS 2CH. - 4CH.
Installation Installation Mono Wiring Parallel Wiring P300X1, P400X1, P500X1BD, P1000X1BD P500X1BD, P1000X1BD PASS-THRU Connect to inputs of 2nd amplifier PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install *Installation option for multi-amp install REMOTE PUNCH LEVEL B SPEAKERS GND INPUT CLIP LEFT RIGHT B+ PLC-OUT A INPUT REM PASS-THRU REMOTE PUNCH LEVEL PLC-IN PASS-THRU A INPUT B SPEAKERS REM GND B+ PLC-OUT LEFT RIGHT PLC-IN INPUT INP
Operation Operation Input Clip Indicator Setup Step 1. illus.-3.1 Step 6. Be sure to disconnect all speakers from the amplifier. LEFT RIGHT REMOTE PUNCH LEVEL Volume PASS-THRU Step 3. Output Clip Indicator Setup Step 7. Be sure to disconnect Punch Level Control - PLC (if equipped) from the amplifier. Step 8. Adjust the Input Level knob until the Output Clip Indicator illuminates to the appropriate color. Repeat for all channel levels of input. illus.-3.
Troubleshooting Troubleshooting NOTE: If you are having problems after installation follow the Troubleshooting procedures below. Check Amplifier for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue. 1. Check in-line fuse on battery positive cable. Replace if necessary. 2. Check fuse(s) on amplifier. Replace if necessary. 3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary. 4.
Installation assistance available at: www.rockfordfosgate.com/rftech 110912 BCF 1230-57270-01 English Printed In China 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .