Owner's Manual

ManualsBrandsRockford Fosgate ManualsAll car amplifiersPunch

Table Of Contents

P1000XSD

Birth

Date

'l_.

_ .

..~

_·

_JZ

1201

Date

Purchase:

_____

sta

llation

Operation

Summary of content (13 pages)

PAGE 1
LJ N P1000XSD Birth Date: __'l_.1_ ..
PAGE 2
0U[YVK\J[PVU Dear Customer, Congratulations on your purchase of the world’s ﬁnest brand of car audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
PAGE 3
:WLJPÄJH[PVUZ Model Rated Power *Continuous Power Rating (RMS) Measured @ 14.4V Crossover Slope Crossover Frequency Punch EQ Operating Voltage Frequency Response Battery Fuse Rating (not supplied) THD+N @ Rated Power P1000X5D 75x4 + 200x1 @ 4 ohms 125x4 + 500x1 @ 2 ohms 250x2 + N/A @ 4 ohms (Bridged) F/R: 12dB/Oct S/SS: 24dB/Oct Variable 50Hz - 500Hz Variable 0 - +18dB @ 45Hz 9 - 16V DC 20Hz - 20kHz ± 1dB 200A <1.
PAGE 4
+LZPNU -LH[\YLZ Gain Control The input gain control is preset to match the output of most source units. Crossover Switch Variable Crossover Is a built-in 12dB/octave Butterworth ﬁlter with a crossover point variable from 50Hz to 500Hz. Selectable switch for High-Pass (HP) or All Pass (AP) Power/Protect LED Power LED illuminates red when the unit is turned on. Protect LED illuminates yellow if a short circuit or to low of an impedance is detected at the speaker connections.
PAGE 5
+LZPNU -LH[\YLZ Punch EQ A Gyrator based Punch EQ that eliminates frequency shift with boost. This works along with the crossover switch on the ampliﬁer. When set to LowPass (LP) operation, this control is a narrow band adjustment variable from 0dB to +18dB @ 45Hz. Infrasonic Filter A ﬁxed 20Hz 24dB/octave ﬁlter designed to prevent frequencies below the audio range from being applied to the subwoofer from the ampliﬁer.
PAGE 6
0UZ[HSSH[PVU working on any vehicle. Contents s P1000X5D - Punch 5 Channel Ampliﬁer s Mounting Hardware s Installation & Operation Manual Installation Considerations The following is a list of tools needed for installation: s Fuse-holder and fuse.
PAGE 7
0UZ[HSSH[PVU Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, ﬁre and/or possible injury. Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system. 1. Plan the wire routing. Keep RCA cables close together but isolated from the ampliﬁer’s power cables and any high power auto accessories, especially electric motors.
PAGE 8
0UZ[HSSH[PVU 5-Channel Stereo Switched 12V to REM Source Unit Less than 18" *Keep grounds as short as possible L....J.....r--..,., __ -- -- -- -~---- .......__............. - I~------ ------------' ---------.... ' ----------' ' .....,.......__...J-1 ---------ctll - - - 1~---- L.."""'i'm(:::J)l -- - -- -- - -ctll - - - I o,- -- - - ----, I Amplifier Connect to chassis ground of vehicle *K.!ep grounds as short as possible 20 min. illus.-2.
PAGE 9
0UZ[HSSH[PVU 3-Channel (2ch Mono *bridged & 1ch Stereo) Switched 12V to REM Source Unit Less than 18" *Keep grounds as shore as possible ~~mm--mm~ -~-L~P>----- ....._,.mm--mm- L..-«m(:::I)J - -c[] .... L_.m~rh------<0 L..""""·:::J[)J -- --- -cO --~~~ --------~ L...-4111CD [l, -- -- - I - - - - - - - - -- - -,, '. --------- . .... mm--mm-~-L~(l,- --- --------mm--mm P>------ -I mm--mm-~-L~~---- ---------cO mm--mm \ - ------ P,---- - ----~ I I I Amplifier Connect to chassis ground of vehi
PAGE 10
6WLYH[PVU Switch in FRONT. position,“ACTIVE” - Front channel inputs only for sub output. Switch in SUB position,“ACTIVE” - Sub inputs for sub output. Adjusting Gain 1. Turn ampliﬁer gains to minimum (counter-clockwise). 2. Turn the source unit volume up to 7/8 maximum (or when distortion is just inaudible). 3. Slowly increase ampliﬁer gain control until adequate volume is achieved. NOTE: Best signal to noise and dynamic range are realized with gain set to minimum.
PAGE 11
;YV\ISLZOVV[PUN Troubleshooting NOTE: If you are having problems after installation follow the Troubleshooting procedures below. Step 1. Check Ampliﬁer for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue. 1. Check in-line fuse on battery positive cable. Replace if necessary. 2. Check fuse(s) on ampliﬁer. Replace if necessary. 3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary. 4.
PAGE 12
>HYYHU[` Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Speakers, Signal Processors, PRIME and PUNCH Ampliﬁers – 1 Year POWER Ampliﬁers – 2 Years Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
PAGE 13
Installation assistance availible at: RFTECH www.rockfordfosgate.com/rftech 101411 BCF 1230-56982-02 3OUTH 2OCKFORD $RIVE s 4EMPE !RIZONA 5NITED 3TATES $IRECT s 4OLL &REE R O C K F O R D F O S G AT E .