MONO AMPLIFIE P3 4 P5D • P70D P~ •
INTRODUCTION Dear Customer, Congratulations on your purchase of the world's finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
GETTING STARTED Welcome to Rockford Fosgate! This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Instollation Section of this manual. Other information can be located by using the Table of Contents.We, at Rockford Fosgate, have worked very hard to make sure all the information in this manual is current.
DESIGN FEATURES 5 4 7 8 11 12 13 P300-1 P400-1 FT\=J;==iA=~:=;=;=+=~=;r::::;:\ 5 4 4 5 6 7 9 10 6 9 10 7 14 15 6 9 10 11 14 15 12 12 13 13 P500-1bd P700-1bd P1000-1bd 11 I. Power LED (Top of unit· Not Shown) - This Blue LED illuminates when the unit is turned on. 2. Thennal LED (Top of unit - Not Shown) - This Red LED illuminates if the amplifier internal components become too hot and engage the thermal protection. The amplifier will shut down to cool if this occurs. 3.
DESIGN FEATURES 12. REM Terminal - The heavy duty, nickel-plated captive c-c1amp wire connector will accept wire sizes from 12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when + 12V DC is applied. 13. Power Terminals - The power and ground are nickel-plated captive c-c1amp wire connectors and will accommodate up to 4 AWG wire. 14.
INSTALLATION MOUNTING LOCATIONS Engine Comportment Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty. Trunk Mounting Mounting the amplifier vertically or inverted will provide adequate cooling of the amplifier. Mounting the amplifier on the floor of the trunk will provide the best cooling of the amplifier.
INSTALLATION 5. Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Insert the bare wire into the GROUND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.
INSTALLATION From ------=:J)J ~ - Source Unit ------=:J)J ~ RCA Inputs Left - - - - Right P500-1bd P700-1bd P1 000-1 bd ;PASS-THR~ Amplifier INPUT OPERATION REMOTE PUNCH EQ (Option) NOTE: Previous (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers. NOTE: Use the instructions that came with the remote for a variety of mountings that fit your preference. Quick Install I. Using the screws supplied, install the mounting clip. 2.
OPERATION INFRASONIC FILTER (PSOO-I bd/P700-1 bd/PI 000-1 bd) INFRASONIC FILTER ~ON Placing the switch to "ON" engages a 28Hz infrasonic filter limiting the amount of low frequency information going to the woofer. Set this to your personal preference while listening to the system one way, then the other. PUNCH EQ~.. • ~ MIN NOTE: We recommend using the infrasonic filter when using vented enclosures with this D OFF MAX FREQ.
TROUBLESHOOTING Procedure 5: Check Amplifier if you experience excess Engine Noise. I. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires. OR 2. Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise. OR 3. Remove existing ground wires for all electrical components. Reground wires to different locations.
LIMITED WARRANTY INFORMATION Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length ofWalTOnty Source Units, Speakers, Signal Processors and PUNCH Amplifiers - I Year POWER Amplifiers - 2Years Any Factory Refurbished. Product - 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States ofAmerica or its possessions.
Installation assistance available at: RFTECH www.rockfordfosgate.com/rftech Rockford Fosgate Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A., (480) 967-3565 - Customer Service 1-800-669-9899 www.rockfordfosgate.com 0812008 B.M. I 1/2009 E.R.
~__J PerForlTlance VeriFication Model: P400-1 Serial #: Engineering CEA Test Voltage: 400 Watts Tested By : GAVIN STEWART Inspection 14.4V Channel Separation: @ Rated Power: 2/9/2010 Birth Date: THD+N CertiFicate Data Actual Power N/A Rated Power: .
Are You Engineered to Rock, Or Wired for Stock? Get a One Year Extended Warranty when you use matching Rockford Fosgate or Lightning Audio Amplifier Installation kit with this Amplifier! We want you to get the performance and reliability that made Rockford Fosgate Amplifiers Famous. Using poor-quality under-spec wiring is a guaranteed way to get less than you paid for from your system.
