21412 BCF 1230-57810-02 Printed in China R O C K F O R D F O S G AT E . C O M 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 www.rockfordfosgate.
* Rated power when amplifier is wired in a bridged configuration. 11.1” x 6.8” x 2” (23.1cm x 17.2cm x 5.1 cm) 9.1” x 6.8” x 2” (21.6cm x 17.2cm x 5.1 cm) 8.5” x 6.8” x 2” (28.5cm x 17.2cm x 5.1 cm) CEA 2006 Power ratings on Rockford Fosgate amplifiers conform to CEA-2006 industry standards. These guidelines mean your amplifier’s output power ratings are REAL POWER numbers, not inflated marketing ratings. 11.2” x 6.8” x 2” (33.5cm x 17.2cm x 5.1 cm) 13.2” x 6.8” x 2” (28.2cm x 17.2cm x 5.
Design Features Design Features Variable Phase Crossover Switch The variable 0-180˚ phase control allows the listener to change the arrival time of the subwoofer sound waves relative to the same frequencies from the main speakers. Variable Crossover Selectable switch for Low-Pass (LP) or All Pass (AP) or High-Pass (HP) Input Switch Setting this switch to the connected inputs aligns the output signal accordingly or can supplement signal to additional channels when not connected.
Installation Installation Contents • Prime Amplifier • 4-pin Molex Connector (if equipped) • Mounting Hardware • Installation & Operation Manual • Allen Wrench • Punch Level Control Installation Considerations The following is a list of tools needed for installation: • Fuse-holder and fuse.
Installation Installation 2-Channel (Stereo) R150X2 2-Channel (Mono) R150X2 PASS-THRU Connect to inputs of 2nd amplifier PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install *Installation option for multi-amp install – + + – GND illus.-2.1 8 REM B+ LEFT RIGHT BRIDGED SPEAKERS – + INPUT PASS-THRU L + – INPUT PASS-THRU L HIGH LEVEL R- LINPUT R+ L+ R GND REM B+ LEFT RIGHT HIGH LEVEL R- LINPUT R+ L+ R BRIDGED SPEAKERS illus.-2.
Installation Installation 4-Channel (Stereo) R250X4, R300X4, R400-4D & R600-4D + 4-Channel (2ch Stereo & 1ch Mono-Bridged) R250X4, R300X4, R400-4D & R600-4D – + – + – + – REAR L GND illus.-2.3 10 REM B+ LEFT BRIDGED REAR RIGHT LEFT RIGHT BRIDGED FRONT + FRONT HIGH LEVEL INPUT FRONT + – + – + – REAR L R REAR – R- LR+ L+ GND REM B+ LEFT BRIDGED REAR RIGHT LEFT RIGHT BRIDGED FRONT FRONT HIGH LEVEL INPUT R- LR+ L+ R REAR FRONT illus.-2.
Installation Installation 4-Channel (2ch Mono-Bridged) R250X4, R300X4, R400-4D & R600-4D + 3-Channel (2ch Bridged & 1ch Parallel) R600X5 – + – + – + – REAR L GND illus.-2.5 12 REM B+ LEFT BRIDGED REAR RIGHT LEFT RIGHT BRIDGED FRONT – + FRONT HIGH LEVEL INPUT + – + – + – SUB REAR REMOTE PUNCH LEVEL FRONT L LEFT FRONT – R- LR+ L+ R REAR + GND REM B+ SUB RIGHT BRIDGED REAR LEFT RIGHT BRIDGED FRONT HIGH LEVEL INPUT R REAR FRONT R- LR+ L+ illus.-2.
Installation Installation 5-Channel (4ch Stereo & 1ch Mono) R600X5 Mono Wiring R250X1 & R500X1D PASS-THRU Connect to inputs of 2nd amplifier *Installation option for multi-amp install – + + – + – – + + – SUB REAR + REMOTE PUNCH LEVEL FRONT – L LEFT GND REM B+ SUB RIGHT BRIDGED LEFT REAR RIGHT BRIDGED FRONT HIGH LEVEL INPUT R REAR FRONT REMOTE PUNCH LEVEL INPUT PASS-THRU L R- LR+ L+ R GND REM B+ SPEAKERS R- LR+ L+ HIGH LEVEL INPUT *Positive(+) and Negative(–) outp
Operation Installation Adjusting Gain Parrallel Wiring* R750-1D & R1200-1D illus.-3.1 1. Turn amplifier gains to minimum (counter-clockwise). 2. Turn the source unit volume up to 7/8 maximum (or when distortion is just inaudible). 3. Slowly increase amplifier gain control until adequate volume is achieved. NOTE: Best signal to noise and dynamic range are realized with gain set to minimum. For a more in depth setting procedure, contact Rockford Technical Support.
Troubleshooting Troubleshooting NOTE: If you are having problems after installation follow the Troubleshooting procedures below. Check Amplifier for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue. 1. Check in-line fuse on battery positive cable. Replace if necessary. 2. Check fuse(s) on amplifier. Replace if necessary. 3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary. 4.
Françias Attention: Assurez-vous toujours que l’ampli est hors tension ou déconnecté avant de connecter les câbles RCA et ce, pour ne pas endommager l’amplifier et/ou les composants connectés. Español Dépannage REMARQUE : En cas de problèmes après l’installation, suivez les procédures de dépannage ci-dessous. Remarque : Lorsque l’installation requiert une entrée de haut niveau (enceinte), utilisez le connecteur à 4 broches Molex pour attacher au câble d’enceinte du véhicule. 9. Connectez les enceintes.
Español Ajuste de la ganancia (illus. 3.1) 1. Gire la ganancia del amplificador al mínimo (sentido contrahorario) 2. Suba el volumen de la unidad fuente a 7/8 del máximo (o cuando apenas se pueda escuchar la distorsión). 3. Lentamente aumente el control de ganancia del amplificador hasta que se obtenga un volumen adecuado. NOTA: Se obtiene la mejor relación de señal a ruido y gama dinámica con la ganancia ajustada en mínimo.
Deutsch Einstellung der Crossover-Frequenz (illus. 3.2,3.3) Folgendes für jeden Kanal einzeln durchführen. Das Platzieren des Crossover-Schalters in der HP-Position schaltet den Verstärker in den Hochpassmodus und erlaubt so das Passieren von Frequenzen oberhalb des Grenzpunkts. Eine Einstellung zwischen 50 und 250 Hz ist möglich. Das Platzieren des Crossover-Schalters in der AP-Position schaltet den Verstärker in den Allpassmodus und verhindert jegliche Crossover-Einstellung.
Italiano Regolazione del guadagno (illus. 3.1) 1. Ruotare il comando del guadagno sull’amplificatore al minimo (in senso antiorario) 2. Ruotare il comando del volume dell’unità sorgente sino a 7/8 del massimo (o sino a quando la distorsione diviene udibile). 3. Aumentare lentamente il comando di guadagno dell’amplificatore sino a ottenere un volume adeguato. NOTA: il miglior rapporto segnale-rumore e la massima gamma dinamica si ottengono con il guadagno al minimo.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Speakers, Signal Processors, PRIME and PUNCH Amplifiers – 1 Year POWER Amplifiers – 2 Years Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
