COMPONENT SPEAKERS T5652-S Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of car audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications SPL (1W1M) • Impedance T5652-S On-Axis(3k,-12dB) Description Nominal Impedance Frequency Response Voice Coil Diameter Power Rating (RMS/Peak) Fs - Free Air Resonance Qts Vas 6.5” (165mm) 2-Way 45-40kHz 1.5” (38.0mm) 150W / 300W Impedance(3k,-12dB) 20 100 18 16 14 80 12 70 10 60 8 50 6 40 4 2 0 20 0.56 10 Sensitivity (2.83V/1M) 91.5dB 100 1K 10K 20K 100K Frequency (Hz) 0.81ft3 (23.0L) 88.
Specifications T5 - Mid-Bass 6.69" (170.0mm) 4.37" (111.0mm) 6.18" (157.0mm) Diameter 7.14" (181.0mm) 0.95" (24.0mm) 3.22" (82.0mm) 2.79" (71.0mm) 5.67" (144.0mm) T5 - Tweeter 2.31" (59.0mm) 0.63" (16.0mm) 0.41" (10.5mm) 0.66" (17.0mm) Mounting Options Surface/Angle Mount 2.3" (58mm) 1.7" (43mm) 1.5" (38mm) Mounting Hole Diameter Flush Mount 2.31" (59mm) 0.63" (16mm) 0.41" (10mm) 1.75" (44mm) Mounting Depth 1.03" (26mm) illus.-1.
Specifications T5 - Crossover 10.12" (257.0mm) 7.40" (188.0mm) 2.13" (54.0mm) illus.-1.
Installation Contents • (1) Pair Power T5 mid-bass speakers • (1) Pair Power T5 tweeters • (1) Power T5 stereo crossover • (1) Pair of grilles/trim rings 5. On models with slotted holes, fit the speaker into the cutout and install the screws in the slots at the top and bottom. This will allow you to rotate the speaker to match the remaining mounting holes. When aligned, tighten the screws. 6. Tighten the screws until the speaker is snug in place to prevent rattling. Do not over tighten the screws.
Installation Wiring Power/Ground illus.-3.1 1. Use illustration for proper connection and be sure to maintain polarity. Red wire is connected to switched 12V source and Black wire is connected to chassis ground. 2. Connect the Power/Ground harness to either RF Link ports. NOTE: Without a 12V source the crossover will still pass signal. To adjust the crossover settings a 12V source must be connected. Chasis Ground (Black) 12V Switched (Red) No reverse polarity protection.
Tweeter Position A The tweeter is positioned low and together in relation to the mid-range. illus.-4.2 System Setup TWEETER LEVEL (dB) +2 0 -2 -4 -4 -2 0 +2 TWEETER PHASE (deg) 180 0 0 180 2.5 3 WOOFER FREQ. (kHz) 3 2.5 WOOFER SLOPE (dB/oct) 12 6 6 12 REMOTE TUNING MODULE Tweeter Level: set by selecting the TL button until the LED above +2 is illuminated. Tweeter Phase: set by selecting the TP button until the LED above 180 is illuminated. Woofer Freq.
Troubleshooting Troubleshooting NOTE: If you are having problems after installation follow the Troubleshooting procedures below. No LED’s illuminated on the Remote Tuning Module when docked. 1. Verify Remote Tuning Module is properly seated in crossover housing. 2. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary. 3. Verify there is 9 to 14.4 Volts present at the power source. Verify quality connection at power source.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Speakers, Signal Processors, PRIME and PUNCH Amplifiers – 1 Year POWER Amplifiers – 2 Years Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
