2014 & UP HARLEY-DAVIDSON® SPEAKERS TMS65 Serial Number: Date of Purchase: Installation & Operation
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of audio products. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications Model TMS65 Nominal Diameter - inch (mm) 6.5 (165) Description 2-Way Nominal Impedance (Ohms) 4Ω Frequency Response (Hz) 65-20kHz Voice Coil Diameter - inch (mm) 1.4 (35.6) Power Handling - Watts (RMS/Peak) 75/150 Fs - Free Air Resonance (Hz) 86.5 Qts 0.52 Vas - cu. ft. (Liter) 0.198 (5.6) Sensitivity (1W/1M) 91dB Sensitivity (2.83V/1M) 94dB Xmax - inch (mm) 0.19 (3.0) Mounting Diameter 5.0 (128) Mounting Depth 2.
Specifications TMS65 90° 45° 6.2” Dia. (157mm) 2.6” (67mm) 2.3” (59mm) 5.6” Dia. (142mm) 2014 & Up Street Guide® Grilles Included 2015 & Up Road Glide® Grilles Included 2014 & Up Tour Pak Grilles Included illus.-1.
Installation Installation Considerations Contents • (1) Pair of 2-Way Speakers • (1) Pair of 2015 & Up Road Glide Grilles • (1) Pair of 2014 & Up Tour-Pak Grilles • Installation & Operation Manual • (1) Pair of 2014 & Up Street Glide Grilles Installation Tools The following is a list of suggested tools needed for installation: • Plastic Trim Panel Pry Tool • Allen Wrench - 3/16”, 5/32” • Torx - T10, T25, T27 This section focuses on some considerations for installing your motorcycle replacement speakers
Installation Front Speakers for Ultra Classic®, Electra Glide®, Street Glide® and Tri Glide® models. You will need to disconnect the harness from the headlight to completely take the fairing off of the motorcycle. Step 1 - Fairing Removal To begin with, remove the top screws below the windshield to remove the windshield. Step 2 - Speaker & Pod Removal After the fairing is removed, this will provide access for the speaker pods that need to be removed so the speakers can be replaced.
Installation Remove the top two bolts with a allen head screwdriver or ratchet. Unplug the module and set it aside. After the top two bolts are removed, remove the three bolts that are under the radio area. Next, remove the last three screws that hold the pod to the fairing. Remove the fairing and set aside for the speaker removal. If your bike is equipped with the optional communication setup, you will need to remove the module to access mounting bolts.
Installation Using a screwdriver, remove the speaker grille that is attached to the fairing. With the pod on a bench, unscrew the mounting screws to remove the factory speaker from the factory pod. Step 3 - Speaker Installation Prior to installing the speaker to the pod, there are alignment pins on the pod that the speaker needs to line up to ensure proper fit. Take the new Rockford speaker and slide the wire connectors over the terminals.
Installation Attach the new Rockford grille to the inside of the fairing. NOTE: The speaker grilles are side specific and have a notch in one of the mounting holes as an indicator. The notch is faced towards the middle of the bike. Reattach the pod with the factory hardware and reinstall any wire harnesses that were removed for the pod removal. Install the outer fairing to the motorcycle after speaker pods and wiring is secured. Front Speakers for Road Glide® and Road Glide Ultra® models.
Installation Unplug the terminals to disconnect the speaker. Secure the speaker to the pod using the factory hardware. Step 2 - Speaker & Grille Installation NOTE: Do not overtighten screws. Doing so can strip the threads on the plastic pod. Take the new Rockford speaker and slide the wire connectors over the terminals. NOTE: The smaller terminal is the positive (+) and the larger terminal is the negative (-).
Installation Rear Speakers for Tour-Pak models. Step 1 - Rear Speaker Removal Unscrew the speaker grilles from the rear pods and remove factory speaker. Unplug the terminals to disconnect the speaker. Step 2 - Rear Speaker Installation Connect the speakers by sliding the speaker wire connector over the speaker terminals NOTE: The smaller terminal is the positive (+) and the larger terminal is the negative (-). Insert the new Rockford speaker into the speaker pod and secure with mounting screws.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty POWER Amplifiers – 2 Years BMW® Direct Fit Speakers – 2 Years Source Units – 1 Year All other products – 1 Year Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.
Installation assistance availible at: 051816 1230-60823-01-A Printed in China www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
