Reaction Super Charger Instruction Manual May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047, 4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617. Other patents pending. Foreign patents pending.
Compliance Your Reaction Super Charger™ pedal has been tested and complies with the following Standards and Directives as set forth by the European Union: Council Directive(s): Compatibility 89/336/EEC Standard(s): EN55013, EN50082-1 Electromagnetic This means that this product has been designed to meet stringent guidelines on how much RF energy it can emit, and that it should be immune from other sources of interference when properly used.
Precautions Refer all service to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply or plug is damaged, liquid has been spilled or objects have fallen into the apparatus or if the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped. DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. QUALIFIED PERSONNEL SHOULD SERVICE THIS EQUIPMENT ONLY.
Introduction Often the tone you seek is that black magic smoky witches’ brew of crunch and edge, or that dry throat bluesy drought stricken Texas dustbowl kind of richness. Turn to Rocktron’s Reaction Super Charger and find your inner musical soul with tone that will make your guitar sing! Using a good overdrive can really make a difference when performing, but a great overdrive can define a player’s signature sound.
Introduction LEVEL determines Output Volume. Even a swamp rat could handle this stomp box. Does your amp need a kick in the pants? The Reaction Super Charger will make your amp’s built-in distortion scream! Looking to add some edge to your crunch tone? The Super Charger will provide that much needed “bite” and “growl” that will push the edge of the envelope! Whatever style you play, from blues to heavy rock, can benefit with a little “Super Charging”.
Descriptions
Descriptions continued......... 1 LEVEL Control - This control determines the amount of level (or volume) of the effect. 2 TONE Control - This control determines the overall EQ of the effect. 3 9VDC Input - This input jack provides 9VDC power to the pedal from the Rocktron DC OnTap 9V power supply (sold seperately). 4 GAIN Control - This control determines the amount of gain (or distortion) added to the signal. 5 ON/OFF Leds - These LEDs shows if the pedal is on or off.
Descriptions continued......... 7 INPUT Jack - Using a standard 1/4” guitar cable, plug your guitar into this jack. 8 THUMB SCREWS for Battery Compartment. Unscrew these thumb screws to access the battery compartment. 9 FOOTSWITCH - Use this switch to turn on or off the pedal. The On/Off Led will show you if the pedal is on or off. 10 OUTPUT Jack - Using a standard 1/4” guitar cable you can plug in another pedal from this jack or plug directly into your amplifier.
Typical Connection
Specifications Maximum Input Maximum Output Imput Impedance Output Impedance Current Consumption Power Requirements Dimensions Weight 8dBu 6Bu 1MΩ 1kΩ 20mA 9V Alkaline Battery or Rocktron DC OnTap Univeral Power Supply (sold seperately). Negative Tip. 125mm x 78mm 61mm 5” x 3.25” x 2.5” 0.7kg 1.
How to change the battery: To change the battery, remove the thumb screws on the top of the pedal and remove the battery compartment cover. Remove the old battery and replace it with a new 9V Alkaline battery. Replace battery in the same area as the old battery was located. Place the battery compartment cover on the pedal and re-insert the thumb screws. Save yourself tons of money in batteries by using the Rocktron DC OnTap Universal Power Supply to power this pedal (sold seperately).
Rocktron - A Division of GHS Corporation 2813 Wilber Ave Battle Creek MI 49037 USA www.rocktron.com info@rocktron.com tel: 1-269-968-3351 rev. 7-27-09 2009.