Quick Start Guide User guide

ManualsBrandsRockwell Automation ManualsEquipment1336E IMPACT

Publication 1336 IMPACT-5.5EN – May, 1999

1336 IMPACT Quick Start Guide

This Quick Start Guide summarizes the basic steps needed to install, start-up, and program the 1336 IMPACT Adjustable

Frequency AC Drive. The information provided Does Not replace the User Manual and is intended for qualified drive service

personnel only. Refer to the 1336 IMPACT User Manual (publication 1336 IMPACT-5.0) for details on other application

considerations and related precautions.

Power Wiring – TB1

Jumper Locations

PE PE

(L1)

(L2)

(L3)

(T1)

(T2)

(T3)

–

Dynamic Brake

Required

Input Fusing

Required Branch

Circuit Disconnect

Shield*

Common Mode Core*

Diagram shows connections that are common for all drives.

Refer to User Manual for Detailed Information.

Ground per

Local Codes

Motor Frame

Motor

Terminator*

* Optional

Nearest

Building Structure Steel

AC Input

to Drive

Ground

Drive Output

to Motor

(Not on all drives) (Not on all drives)

Conduit/4-Wire Cable

BRK

–

Important: Verify motor insulation system peak voltage

rating. For cable lengths greater than 6.1

meters (20 feet), consult the User Manual.

All Other Frames

LANGUAGE MODULE

ALLEN-BRADLEY

JOG

ESC

SEL

Frames A1 – A4

J4 (TB4)

L Option Board

Jumpers

LANGUAGE MODULE

ALLEN-BRADLEY

J7 (TB7)

J10 (TB10)

TB10

TB11

Summary of content (12 pages)

PAGE 1
336 IMPACT Quick Start Guide This Quick Start Guide summarizes the basic steps needed to install, start-up, and program the 1336 IMPACT Adjustable Frequency AC Drive. The information provided Does Not replace the User Manual and is intended for qualified drive service personnel only. Refer to the 1336 IMPACT User Manual (publication 1336 IMPACT-5.0) for details on other application considerations and related precautions.
PAGE 2
1336 IMPACT Quick Start Guide Wiring I/O – A-Frames J4 (TB4) J7 (TB7) + Analog Input 1 - 1 Com 2 -10V 3 Shield 4 2 Shield Analog Input 2 +10V 1 3 + 4 - 5 Shield Analog Output 1 5 - 6 6 + 7 - 8 Shield Analog Output 2 + 8 - 9 9 + 10 - 11 Shield J10 (TB10) 7 Shield 4 to 20 mA Pulse Source + 1 2 3 4 5 6 7 8 9 10 11 + 11 - 12 4 to 20 mA 12 TE 10 Shield 12 * The power supply is for drive input use only.
PAGE 3
1336 IMPACT Quick Start Guide L Option Board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Status Start Start Start Start Start Start Start Start Start Start Run Fwd Run Fwd Run Fwd Run Fwd Run Fwd Start Start Start Start Start Start Run Fwd Run Fwd Run Fwd Run Fwd Start Start Start Run Fwd Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt Stop/Clr Flt
PAGE 4
1336 IMPACT Quick Start Guide 1. Verify that AC line power and control power match the drive rating. 2. If an L option is installed, verify that the Stop and Enable interlock inputs are present. If this option is not installed, verify that jumpers are installed at pins 3 and 4 and 17 and 18 on J5 on A Frame drives or J2 on B Frame and up drives. Refer to Jumper Locations. 3. If standard I/O is being used, verify that jumpers are wired correctly. 4.
PAGE 5
1336 IMPACT Quick Start Guide Drive Dimensions To determine the size of your drive, refer to the following illustration and table. Frame Height A1 A2 A3 A4 B C D E-Enclosed E-Open F G H De pth idth W ➀ Width x Height x Depth Millimeters (inches) 215.9 (8.50) x 290.0 (11.42) x 160.0 (6.30) 215.9 (8.50) x 290.0 (11.42) x 180.5 (7.10) 215.9 (8.50) x 290.0 (11.42) x 207.0 (8.15) 260.0 (10.24) x 350.0 (13.78) x 212.0 (8.35) 276.4 (10.88) x 476.3 (18.75) x 225.0 (8.86) 301.8 (11.88) x 701.0 (27.
PAGE 6
1336 IMPACT Quick Start Guide HIM Structure Power-Up and Status Display or or or Operator Level or Choose Mode Mode Level EEProm Save Values Recall Values Reset Defaults Drive to HIM HIM to Drive Control Status Search Parameters Links Password Control Logic Reset Drive1 Fault Queue Warning Queue Display Login Logout Modify Process Process Display Link Program Start Up Set Links Clear All Links File Level Monitor Control Motor Status Drive/Inv Status SCANport Status Fault Status Test
PAGE 7
1336 IMPACT Quick Start Guide Parameters - Files, Groups, and Elements Name Monitor Motor Status Motor Speed Motor Frequency Motor Current Motor Voltage Motor Voltage % Motor Torque % Motor Flux % Motor Power% Enc Pos Fdbk Low Enc Pos Fdbk Hi Int Torque Ref Drive/Inv Status DC Bus Voltage Logic Input Sts Drive/Inv Status Drive/Inv Sts 2 Run Inhibit Sts Command Spd Sts Torque Limit Sts Spd Reg Output Spd Error SCANport Status Dir/Ref Owner Start/Stop Owner Jog1/Jog2 Owner Ramp/ClFlt Owner Flux/Trim Owner F
PAGE 8
1336 IMPACT Quick Start Guide Name Fault Config cont.
PAGE 9
1336 IMPACT Quick Start Guide Name Motor Inverter Motor Nameplate Nameplate HP Nameplate RPM Nameplate Amps Nameplate Volts Namplate Hz Motor Poles Service Factor Encoder Data Encoder PPR Inverter PWM Frequency Inverter Amps Inverter Volts Motor Constants Stator Resistance Leak Inductance Flux Current Slip Gain Motor Poles Application Flux Braking Bus/Brake Option DC Braking/Hold Bus/Brake Option DC Brake Current DC Brake Time 400% Mtr Current Max Mtr Current Fast Flux Up Bus/Brake Option Fast Flux Level S
PAGE 10
1336 IMPACT Quick Start Guide This Page Intentionally Blank 10 Publication 1336 IMPACT-5.
PAGE 11
1336 IMPACT Quick Start Guide Publication 1336 IMPACT-5.
PAGE 12
Allen-Bradley, a Rockwell Automation Business, has been helping its customers improve productivity and quality for more than 90 years. We design, manufacture and support a broad range of automation products worldwide. They include logic processors, power and motion control devices, operator interfaces, sensors and a variety of software. Rockwell is one of the world’s leading technology companies. Worldwide representation.