Owner manual

ManualsBrandsRockwell Automation ManualsEquipment1747-DTAM-E,D17476.1 Data Table Access Module (DTAM)

Table Of Contents

1747-6.1, Data Table Access Module User Manual
Important User Information
Summary of Changes
- New Information
Table of Contents
Preface
- Who Should Use this Manual
- Purpose of this Manual
  - Contents of this Manual
  - Related Documentation
- Common Techniques Used in this Manual
- Allen-Bradley Support
1 - Data Table Access Module Overview
- Module Overview
2 - Installation and Power Up
- European Union Directive Compliance
  - EMC Directive
- Mounting the Module
- Connecting Your Equipment
- Module Configuration and Adjustments
- Power-Up Sequence
3 - Module Setup Procedure
- Keyboard Description
- Factory Default Settings
- Entering the Setup Mode
- Selecting the Language
- Selecting the Node Address
- Setting the Baud Rate
- Setting the Auto Attach Function
- Backlighting the LCD
- Setting the Monitor Override Function
- Accepting Module Setup Parameters
- Using the Module Reset
4 - Attaching to a Processor
- Manual Attach Procedure
- Auto Attach Procedure
- Ready Attached Screen
- Backspace Function During Attach Procedure
- Attaching to a Password Protected Processor
5 - Monitoring and Modifying Data
- Operating Modes
- Logical Data File Addressing
- Backspace Function During Data File Address Entry
- Quick Access Addressing
- Entering Data File Addresses
- How to Change Displayed Data File Addresses
- How to Change Data File Values
6 - Quick Recall Functions
- Quick Recall Function Overview
- Defining Quick Recall Functions
- Using Quick Recall Functions
- Clearing Quick Recall Functions
7 - Processor Control Functions
- Changing the Processor to Run Mode
- Changing the Processor to Program Mode
- Viewing Processor Faults
- Clearing Processor Faults
- Transferring Memory from EEPROM to RAM
- Transferring Memory from RAM to EEPROM
8 - Message Capability
- Message Overview
- Programming the MSG Instruction
- 5/02 Control Block Configuration
- 5/03 Control Block Configuration
- 8-Word Message
- 16-Word Message
- 12-Word Message
- 13-Word Message
- 18-Word Message
- 1-Word Message
- Application Example 1
- Application Example 2
9 - Troubleshooting
- Troubleshooting Module Problems Using the Communications LED
- Troubleshooting Module Problems Using the LCD
- Troubleshooting Communication Problems Using the LCD
- Troubleshooting Function Problems Using the LCD
- Troubleshooting MSG Instruction Error Codes
- Troubleshooting Processor Faults Using the LCD
A - Specifications
- Operating Power
- Temperature and Humidity
- General Characteristics
B - SLC 500 Data Files and Logical Addressing
- Data Files
C - Module Display Character Set
- Display Character Table
D - Mounting Template
- Using the Template
Index
Back Cover

Module Setup Procedure 3-7

Publication 1747-6.1

Accepting Module

Setup Parameters

If you accept the new configuration, the parameters are written to the

module’s nonvolatile memory. If you reject the new parameters, the

previous setup configuration remains unchanged.

• To accept the configuration:

Press [

• To reject the configuration:

Press [

The module then performs a reset and self test. Upon completion, the

LCD displays one of the two Ready screens. Refer to chapter 4,

AttachingtoaProcessor, for a description of these displays.

Using the Module

Reset

The module reset key sequence is available at any time and during

any function sequence. Use it when a nonrecoverable fault condition

error code is displayed or when the module appears to be

nonfunctional. Refer to chapter 9, Troubleshooting, for fault

conditions and error codes.

To reset the module:

Press [

][ ][ ] simultaneously and hold until this message

displays:

This reset message continues to display during the reset procedure

and the diagnostic test which follows. Upon completion, one of the

Ready screens displays.

Accept Setup

Confirm?

DTAM Reset

In Progress