Owner manual

ManualsBrandsRockwell Automation ManualsEquipment1747-DTAM-E,D17476.1 Data Table Access Module (DTAM)

Table Of Contents

1747-6.1, Data Table Access Module User Manual
Important User Information
Summary of Changes
- New Information
Table of Contents
Preface
- Who Should Use this Manual
- Purpose of this Manual
  - Contents of this Manual
  - Related Documentation
- Common Techniques Used in this Manual
- Allen-Bradley Support
1 - Data Table Access Module Overview
- Module Overview
2 - Installation and Power Up
- European Union Directive Compliance
  - EMC Directive
- Mounting the Module
- Connecting Your Equipment
- Module Configuration and Adjustments
- Power-Up Sequence
3 - Module Setup Procedure
- Keyboard Description
- Factory Default Settings
- Entering the Setup Mode
- Selecting the Language
- Selecting the Node Address
- Setting the Baud Rate
- Setting the Auto Attach Function
- Backlighting the LCD
- Setting the Monitor Override Function
- Accepting Module Setup Parameters
- Using the Module Reset
4 - Attaching to a Processor
- Manual Attach Procedure
- Auto Attach Procedure
- Ready Attached Screen
- Backspace Function During Attach Procedure
- Attaching to a Password Protected Processor
5 - Monitoring and Modifying Data
- Operating Modes
- Logical Data File Addressing
- Backspace Function During Data File Address Entry
- Quick Access Addressing
- Entering Data File Addresses
- How to Change Displayed Data File Addresses
- How to Change Data File Values
6 - Quick Recall Functions
- Quick Recall Function Overview
- Defining Quick Recall Functions
- Using Quick Recall Functions
- Clearing Quick Recall Functions
7 - Processor Control Functions
- Changing the Processor to Run Mode
- Changing the Processor to Program Mode
- Viewing Processor Faults
- Clearing Processor Faults
- Transferring Memory from EEPROM to RAM
- Transferring Memory from RAM to EEPROM
8 - Message Capability
- Message Overview
- Programming the MSG Instruction
- 5/02 Control Block Configuration
- 5/03 Control Block Configuration
- 8-Word Message
- 16-Word Message
- 12-Word Message
- 13-Word Message
- 18-Word Message
- 1-Word Message
- Application Example 1
- Application Example 2
9 - Troubleshooting
- Troubleshooting Module Problems Using the Communications LED
- Troubleshooting Module Problems Using the LCD
- Troubleshooting Communication Problems Using the LCD
- Troubleshooting Function Problems Using the LCD
- Troubleshooting MSG Instruction Error Codes
- Troubleshooting Processor Faults Using the LCD
A - Specifications
- Operating Power
- Temperature and Humidity
- General Characteristics
B - SLC 500 Data Files and Logical Addressing
- Data Files
C - Module Display Character Set
- Display Character Table
D - Mounting Template
- Using the Template
Index
Back Cover

7-4 Processor Control Functions

Publication 1747-6.1

Transferring Memory

from EEPROM to RAM

You may transfer a program between processor EEPROM and RAM

memory.

To transfer EEPROM to RAM, from any display:

1. Configure the module for the Modify mode.

2. Make sure the processor is in the Program mode.

3. To initiate the memory transfer:

Press

4. The module displays:

5. To confirm:

Press

To abort the memory transfer:

Press

The display returns to the previous Ready

Attached screen.

6. When the transfer is initiated, the module displays:

7. If the memory transfer is successful, the module displays:

If the program contained in the EEPROM is password-protected,

you are required to re-enter the password at this point.

8. When the transfer is complete (or the password is entered, if

required), the module displays the Ready Attached screen:

If an error occurs during the transfer, an error message displays on the

bottom line of the display. Refer to chapter 9, Troubleshooting.

Confirm?

PROM -> CPU RAM,

Working....

PROM -> CPU RAM,

Transfer Success

PROM -> CPU RAM,

RDY> 4 RHALT

5/02 1111