Installation Instructions ControlLogix EtherNet/IP Module Catalog Number 1756-EN2F Topic Page About the Module 6 Before You Begin 7 Determine Module Slot Location 8 Install the Module 11 Connect the Module to the EtherNet/IP Network 13 Program the Module via the USB Port 14 Configure the Module 15 Apply Chassis Power 15 Check Power Supply and Module Status 16 Install or Remove the Module Under Power 17 Interpret the Status Indicators 19 Specifications 21 About This Publication Use
ControlLogix EtherNet/IP Module Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences between solid-state equipment and hard-wired electromechanical devices.
ControlLogix EtherNet/IP Module 3 North American Hazardous Location Approval The following information applies when operating this equipment in hazardous locations. Informations sur l’utilisation de cet équipement en environnements dangereux. Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only.
ControlLogix EtherNet/IP Module Environment and Enclosure ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating. This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR 11.
ControlLogix EtherNet/IP Module 5 ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: • • • • • • Touch a grounded object to discharge potential static. Wear an approved grounding wriststrap. Do not touch connectors or pins on component boards. Do not touch circuit components inside the equipment. Use a static-safe workstation, if available.
ControlLogix EtherNet/IP Module About the Module Use this figure to identify the external features of the module.
ControlLogix EtherNet/IP Module 7 Before You Begin Before you install the module, you must install and connect a ControlLogix chassis and power supply. 1 2 20805-M Item Description Item Description 1 1756-A4 chassis 2 Power supply To install these products, refer to these publications.
ControlLogix EtherNet/IP Module Determine Module Slot Location Install the module in any slot in the ControlLogix chassis. You can install multiple 1756-EN2F modules in the same chassis. The following figure shows chassis slot numbering in a four-slot chassis. Slot 0 is the first slot and is always the leftmost slot in the rack.
ControlLogix EtherNet/IP Module 9 Set the Network Address The module ships with the rotary switches set to 999 and BOOTP enabled. You can set the network Internet Protocol (IP) address three ways. • Use the rotary switches on the top of the module. • Use a BOOTP server or Dynamic Host Configuration Protocol (DHCP) server, such as Rockwell Automation BOOTP/DHCP. • Use the Rockwell Automation RSLinx or RSLogix 5000 software.
ControlLogix EtherNet/IP Module To reset the module to its initial out-of-the-box settings, reset the switches to 888 and cycle power. IMPORTANT Do not use the 888 switch setting during normal module operation. After cycling power with the switches set to 888, remove the module and set the switches to their final value. When you set the rotary switches to a value other than 888, or to the valid IP address values 001…254, the software configuration determines the IP address.
ControlLogix EtherNet/IP Module 11 Install the Module Follow this procedure to install the module. 1. Align the circuit board with top and bottom guides in the chassis. 1 Item Description 1 Circuit board 2. Slide the module into the chassis.
ControlLogix EtherNet/IP Module Make sure that the module backplane connector properly connects to the chassis backplane. TIP The module is properly installed when it is flush with the power supply or other installed modules.
ControlLogix EtherNet/IP Module 13 Connect the Module to the EtherNet/IP Network Attach the LC2 fiber cable to the Ethernet port on the bottom of the module as shown. ATTENTION: Do not look directly into the optical port. Under certain conditions, viewing the optical port may expose the eye to hazard. When viewed under some conditions, the optical port may expose the eye beyond the maximum permissible exposure recommendations. Class 1 laser product.
ControlLogix EtherNet/IP Module Program the Module via the USB Port WARNING: The USB port is intended for temporary local programming purposes only and is not intended for permanent connection. If you connect or disconnect the USB cable with power applied to this module or any device on the USB network, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. A Samtec Inc.
ControlLogix EtherNet/IP Module 15 Configure the Module Follow these steps to configure the module. 1. In RSLogix 5000 software, from the Controller Organizer, select New Module. 2. Select the module you want to configure. For more configuration information, refer to the EtherNet/IP Modules in Logix5000 Control Systems User Manual, publication ENET-UM001. View or download this publication at http://www.rockwellautomation.com/literature.
ControlLogix EtherNet/IP Module Check Power Supply and Module Status Check the status indicators and alphanumeric display to determine whether the power supply and module are operating properly.
ControlLogix EtherNet/IP Module 17 When power is applied to the module, the alphanumeric display should cycle through these states: • TEST • PASS • OK • REV x.x where x.x is the module’s firmware revision. The display then alternates between OK and the module’s EtherNet/IP address. Install or Remove the Module Under Power You can install or remove this module while chassis power is applied. WARNING: When you insert or remove the module while backplane power is on, an electrical arc can occur.
ControlLogix EtherNet/IP Module 2. Slide the module out of the chassis. IMPORTANT If you want to replace an existing module with an identical one, and you want to resume identical system operation, you must install the new module in the same slot.
ControlLogix EtherNet/IP Module 19 Interpret the Status Indicators If the alphanumeric display and status indicators do not sequence through the expected states, refer to these tables. The three bi-color (red/green) status indicators on the module provide diagnostic information about the module and its connections to the network.
ControlLogix EtherNet/IP Module Status Indicators Indicator Status Description NET Off The module is not powered. Verify that there is chassis power and that the module is completely inserted into the chassis and backplane. The module does not have a valid IP address. Make sure the module has been configured with a valid IP address. Flashing green The module has an IP address, but has no established connections. Green The module has an IP address and at least one established connection.
ControlLogix EtherNet/IP Module 21 Specifications Technical Specifications 1756-EN2F Attribute 1756-EN2F Enclosure type rating None (open-style) USB connector Ethernet BNC USB Type B receptacle USB port USB 1.1 USB Device Recommended USB cable for USB port Samtec cable, PN RSP-199350 Fiber connector LC2 Fiber cable 100BASE-FX-compliant multimode GI fiber cable Module location Any slot in the ControlLogix chassis Backplane current 1.2 A @ 5.
ControlLogix EtherNet/IP Module Environmental Specifications 1756-EN2F Attribute 1756-EN2F Temperature, nonoperating 40…85 °C (-40…185 °F) • EC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold) • IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat) • IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock) Relative humidity 5…95% noncondensing • IEC 60068-2-30 (Test Db, Unpackaged Damp Heat) Vibration • IEC 60068-2-6 (Test Fc, Operating) 2 g @ 10…500 Hz Shock, operating IEC 60068-2-27 (Te
ControlLogix EtherNet/IP Module 23 Certifications 1756-EN2F Certifications(1) (when product is marked) 1756-EN2F cULus • UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584. • cULus UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada. See UL File E194810. CSA • Certified Process Control Equipment. See CSA File LR54689C. • CSA Certified Process Control Equipment for Class I, Division 2 Group A,B,C,D Hazardous Locations.
ControlLogix EtherNet/IP Module Additional Resources Refer to these publications for additional information. Resource Description Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.
ControlLogix EtherNet/IP Module 25 Notes: Rockwell Automation Publication 1756-IN606B-EN-P - April 2010
ControlLogix EtherNet/IP Module Notes: Rockwell Automation Publication 1756-IN606B-EN-P - April 2010
ControlLogix EtherNet/IP Module 27 Rockwell Automation Publication 1756-IN606B-EN-P - April 2010
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.
