Instruction Manual
Table Of Contents
- 1769-UM006E-EN-P, Compact High-speed Counter Module User Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Module Overview
- 2 - Module Operation
- 3 - Installation and Wiring
- 4 - Module Configuration, Output, and Input Data
- Configure the Module
- Configuration Array
- General Configuration Bits
- Filter Selection
- Program Mode and Program State Run
- Output Program Value (Out0ProgramValue through Out3ProgramValue)
- Output Fault Mode and Output Fault State Run
- Output Fault Value (Out0FaultValue through Out3FaultValue)
- Counter Maximum Count (CtrnMaxCount)
- Counter Minimum Count (CtrnMinCount)
- Counter Preset (CtrnPreset)
- Counter Hysteresis (CtrnHysteresis)
- Counter Scalar (CtrnScalar)
- Cyclic Rate Update Time (CtrnCyclicRateUpdateTime)
- Configuration Flags
- Range High Limit (Range0To11[n].HighLimit) and Range Low Limit (Range0To11[n].LowLimit)
- Range Output Control (Range0To11[n].OutputControl)
- Range Configuration Flags
- Output Array
- Output on Mask (OutputOnMask.0 through OutputOnMask.15)
- Output Off Mask (OutputOffMask.0 through OutputOffMask.15)
- Range Enable (RangeEn.0 through RangeEn.15)
- RBF - Reset Blown Fuse (ResetBlownFuse)
- Control Bits
- Range High Limit or Direct Write Value (Range12To15[n].HiLimOrDirWr)
- Range Low Limit (Range12To15[n].LowLimit)
- Range Output Control (Range12To15[n].OutputControl)
- Range Configuration Flags (12To15)
- Input Array
- Input State (InputStateA0 through InputStateZ1)
- Readback (Readback.0 through Readback.15)
- Status Flags
- Range Active (RangeActive.0 through RangeActive.15)
- Current Count (Ctr[n].CurrentCount)
- Stored Count (Ctr[n].StoredCount)
- Current Rate (Ctr[0].CurrentRate to Ctr[3].CurrentRate)
- Pulse Interval (Ctr[0].PulseInterval and Ctr[1].PulseInterval)
- Status Flags
- 5 - Diagnostics and Troubleshooting
- A - Specifications
- B - Program a 1769-HSC Module, CompactLogix Controller, and 845F Incremental Encoder with RSLogix 5000 Software
- C - Program a 1769-HSC Module, MicroLogix 1500 Controller, and 845F Incremental Encoder with RSLogix 500 Software
- D - Programming Quick Reference
- E - History of Changes
- Glossary
- Index
- Back Cover
Rockwell Automation Publication 1769-UM006E-EN-P - July 2013 121
Diagnostics and Troubleshooting Chapter 5
Ctr1MaxCount
Ctr1MinCount
Ctr1Preset
(1)
Ctr1Hysteresis
(2)
Ctr1Scalar
(2)
Ctr1CyclicRateUpdateTime
(2)
Ctr1Config.OperationalMode
Ctr1Config.StorageMode
Ctr1Config.Linear
16 and 17
18 and 19
20 and 21
22
23
24
25
25
25
--
--
--
--
--
--
0to3
8to10
12
X
X
(1)
X
X
X
X
X
X
Ctr2MaxCount
Ctr2MinCount
Ctr2Preset
(1)
Ctr2Hysteresis
(2)
Ctr2Scalar
(2)
Ctr2CyclicRateUpdateTime
(2)
Ctr2Config.Linear
26 and 27
28 and 29
30 and 31
32
33
34
35
--
--
--
--
--
--
12
X
X
(1)
X
X
X
X
Ctr3MaxCount
Ctr3MinCount
Ctr3Preset
(1)
Ctr3Hysteresis
(2)
Ctr3Scalar
(2)
Ctr3CyclicRateUpdateTime
(2)
Ctr3Config.Linear
36 and 37
38 and 39
40 and 41
42
43
44
45
--
--
--
--
--
--
12
X
X
(1)
X
X
X
X
Ranges 46 to 117 -- Can be changed wile counters and ranges are enabled
(1) CtrnPreset can be changed while CtrnEn=1.
(2) Does not apply to the L23E packaged controllers embedded HSC.
Table 24 - ‘BadModConfigUpdate’ Error Prohibited Configuration Settings (Continued)
Configuration Parameters Array Position Prohibited from changing when indicated bits (X) are set
Word Bit Ctr0EN Ctr1EN Ctr2EN Ctr3EN RangeEN