Instruction Manual
Table Of Contents
- 1769-UM006E-EN-P, Compact High-speed Counter Module User Manual
- Summary of Changes
- Table of Contents
- Preface
- 1 - Module Overview
- 2 - Module Operation
- 3 - Installation and Wiring
- 4 - Module Configuration, Output, and Input Data
- Configure the Module
- Configuration Array
- General Configuration Bits
- Filter Selection
- Program Mode and Program State Run
- Output Program Value (Out0ProgramValue through Out3ProgramValue)
- Output Fault Mode and Output Fault State Run
- Output Fault Value (Out0FaultValue through Out3FaultValue)
- Counter Maximum Count (CtrnMaxCount)
- Counter Minimum Count (CtrnMinCount)
- Counter Preset (CtrnPreset)
- Counter Hysteresis (CtrnHysteresis)
- Counter Scalar (CtrnScalar)
- Cyclic Rate Update Time (CtrnCyclicRateUpdateTime)
- Configuration Flags
- Range High Limit (Range0To11[n].HighLimit) and Range Low Limit (Range0To11[n].LowLimit)
- Range Output Control (Range0To11[n].OutputControl)
- Range Configuration Flags
- Output Array
- Output on Mask (OutputOnMask.0 through OutputOnMask.15)
- Output Off Mask (OutputOffMask.0 through OutputOffMask.15)
- Range Enable (RangeEn.0 through RangeEn.15)
- RBF - Reset Blown Fuse (ResetBlownFuse)
- Control Bits
- Range High Limit or Direct Write Value (Range12To15[n].HiLimOrDirWr)
- Range Low Limit (Range12To15[n].LowLimit)
- Range Output Control (Range12To15[n].OutputControl)
- Range Configuration Flags (12To15)
- Input Array
- Input State (InputStateA0 through InputStateZ1)
- Readback (Readback.0 through Readback.15)
- Status Flags
- Range Active (RangeActive.0 through RangeActive.15)
- Current Count (Ctr[n].CurrentCount)
- Stored Count (Ctr[n].StoredCount)
- Current Rate (Ctr[0].CurrentRate to Ctr[3].CurrentRate)
- Pulse Interval (Ctr[0].PulseInterval and Ctr[1].PulseInterval)
- Status Flags
- 5 - Diagnostics and Troubleshooting
- A - Specifications
- B - Program a 1769-HSC Module, CompactLogix Controller, and 845F Incremental Encoder with RSLogix 5000 Software
- C - Program a 1769-HSC Module, MicroLogix 1500 Controller, and 845F Incremental Encoder with RSLogix 500 Software
- D - Programming Quick Reference
- E - History of Changes
- Glossary
- Index
- Back Cover
Rockwell Automation Publication 1769-UM006E-EN-P - July 2013 67
Module Configuration, Output, and Input Data Chapter 4
4
Not used Out
3
FSR
Out
2
FSR
Out 1
FSR
Out0
FSR
Out3
FM
Out 2
FM
Out1
FM
Out0
FM
Output Fault Mode and
Output Fault State Run
5
Not used Out3
FV
Out 2
FV
Out1
FV
Out0
FV
Output Fault Value
6 Ctr0MaxCount Counter 0 Maximum
Count
7
8 Ctr0MinCount Counter 0 Minimum
Count
9
10 Ctr0Preset Counter 0 Preset
11
12 Ctr0Hysteresis Counter 0 Hysteresis
13 Ctr0Scalar Counter 0 Scalar
14 Ctr0CyclicRateUpdateTime Counter 0 Cyclic Rate
Update Time
15
Not used Lin-
ear
Not
used
Storage mode Not used Operational mode Counter 0
Configuration Flags
16 Ctr1MaxCount Counter 1 Maximum
Count
17
18 Ctr1MinCount Counter 1 Minimum
Count
19
20 Ctr1Preset Counter 1 Preset
21
22 Ctr1Hysteresis Counter 1 Hysteresis
23 Ctr1Scalar Counter 1 Scalar
24 Ctr1CyclicRateUpdateTime Counter 1 Cyclic Rate
Update Time
25
Not used Lin-
ear
Not
used
Storage mode Not used Operational mode Counter 1
Configuration Flags
26 Ctr2MaxCount Counter 2 Maximum
Count
27
28 Ctr2MinCount Counter 2 Minimum
Count
29
30 Ctr2Preset Counter 2 Preset
31
32 Ctr2Hysteresis Counter 2 Hysteresis
33 Ctr2Scalar Counter 2 Scalar
34 Ctr2CyclicRateUpdateTime Counter 2 Cyclic Rate
Update Time
Table 12 - Configuration Array - 1769-HSC Module and CMX 5370 L2 Packaged Controller Embedded HSC (Continued)
Word
Bit
Function
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00