Quick Start - FRN 1.xx - 3.xx Instruction Manual

Italiano-17
L’inverter PowerFlex 40P è concepito per un avviamento semplice ed efficiente. Il gruppo
Programma contiene i parametri usati con maggiore frequenza.
Parametri del gruppo Visualizzazione
N. Parametro Min/Max Display/Opzioni
b001 [Freq uscita] 0,00/[Frequenza max] 0,01 Hz
b002 [Freq comandata] 0,00/[Frequenza max] 0,01 Hz
b003 [Corr. in uscita] 0,0/(Ampere inverter × 2) 0,01 Amp
b004 [Tens. in uscita] 0/Tens nom inverter 1 V CA
b005 [Tens. bus CC] In base alla taglia
dell’inverter
1 V CC
b006 [Stato unità] 0/1 (1 = Condizione vera) Bit 3
Bit 2 Bit 1 Bit 0
In decel. In accel. Avanti In marcia
b007-
b009
[Codice guasto x] F2/F122 F1
b010 [Display di proc.] 0,00/9999 0,01 – 1
b012 [Fonte controllo] 0/112 Cifra 2 e 3 = Comando velocità
Cifra 1 = Comando di avvio
(Vedere P038; 9 = “Freq Jog”) (Vedere P036; 9 = “Jog”)
b013 [Stato ingr contr] 0/1 (1 = Ingresso
presente)
Bit 3
Bit 2 Bit 1 Bit 0
TransDBacc Ingr arr Dir/Indiet Avvio/Avanti
b014 [Stato ingr dig] 0/1 (1 = Ingresso
presente)
Bit 3
Bit 2 Bit 1 Bit 0
Ingr digit 4 Ingr digit 3 Ingr digit 2 Ingr digit 1
b015 [Stato comun.] 0/1 (1 = Condizione vera) Bit 3
Bit 2 Bit 1 Bit 0
Errore DSI Tx Rx
b016 [Vers softw contr] 1.00/99.99 0.01
B017 [Tipo inverter] 1001/9999 1
b018 [Tempo avvio scad] 0/9999 ore 1 = 10 ore
b019 [Dati testpoint] 0/FFFF 1 esadecimale
b020 [Ingr anlg 0-10 V] 0,0/100,0% 0,1%
b021 [Ingr an 4-20 mA] 0,0/100,0% 0,1%
b022 [Potenza Uscita] 0,00/(Potenza inverter × 2) 0,01 kW
b023 [Fatt pot uscita] 0,0/180,0 deg 0,1 deg
b024 [Temp inverter] 0/120°C 1°C
b025 [Stato conteggio] 0/9999 1
b026 [Stato timer] 0,0/9999 sec 0,1 sec
b028 [Stato logica STP] 0/8 1
b029 [Corr. di coppia] 0,0/(Ampere inverter × 2) 0,01 Amp
Avviamento facilitato con i parametri di base del
gruppo Programma
= Prima di cambiare questo parametro, arrestare l’inverter.
N. Parametro Min/Max Display/Opzioni Valore predefinito
P031 [Tens Targa mot.] 20/Tens nom inverter 1 V CA In base alla taglia
dell’inverter
Impostare sulla tensione nominale riportata sulla targhetta dati
del motore.
P032 [Freq. nom. mot.] 15/500 Hz 1 Hz 60 Hz
Impostare sulla frequenza nominale riportata sulla targhetta dati
del motore.
P033 [Corr sovracc mot] 0,0/(ampere nominali inverter× 2) 0,1 A In base alla taglia
dell’inverter
Impostato sulla corrente motore massima consentita.
P034 [Freq minima] 0,00/500,0 Hz 0,01 Hz 0,00 Hz
Imposta il livello minimo di frequenza generato di continuo
dall’inverter.
P035 [Frequenza max] 0,00/500,0 Hz 0,01 Hz 60,00 Hz
Imposta il livello massimo di frequenza generato dall’inverter.