Manual

Error and System Messages
Appendix B
B-2
Message Description
2
2MB RAM ISBAD/MISSING The control hasdiscovered theRAM SIMMsfor the twomegabyte extendedstorage optionare
either damagedor missing. The RAMSIMMs must beinstalled or replaced. Contact your Allen
Bradley salesrepresentative forassistance.
9
9/SERIES LATHE - CANNOTUSE MILL AMP The controlwas poweredup witha lathesoftware option chip installed, when theAMP file that
was downloadedwas configuredfor a mill.
9/SERIES MILL- CANNOT USELATHE AMP The control was poweredup witha mill softwareoption chipinstalled, when theAMP filethat
was downloadedwas configuredfor a lathe.
7300
7300 NAMES TABLE IS CORRUPTED 7300 program namedoesn’t match correspondingname in cross-reference table.
7300 PATTERN NAMETOOLONG More than5 digitshave beenused in the pattern name.
A
A RETRACEBUFFER WAS DELETED The control requiredone (ormore) of theblock retrace buffers toperform anecessary block
look-ahead operation (refer toblock look-aheadin theuser’smanual). When this occurs, less
block retraceoperations canbe performedthan AMPis configuredto allow. If this erroroccurs,
to improve control efficiency, it is recommended that thenumber of allowableblock retrace
blocks set inAMP belowered or addadditional RAM toyou system.
ABS POSITIONNOT INITIALIZED Thismessage indicatesthat axes withabsolute encodershave not beenhomed. These axes
require an initial homingoperation toestablish theabsolute position.
ABSOLUTE FEEDBACKFAILURE The controlhas detecteda lossof feedback from theabsolute encoder. The most likely cause
of this errorwould bea brokenor disconnectedwire. Axis homingmay berequired after the
error conditionis corrected.
ACC/DEC CONFIGURATION ERROR An axisconfiguration error wasdetercted by the controlwhen manual acc/dec wasrequested in
a program block.
ACCUM. AND EXPECTEDLIFE ARE 0 No toollife datawas enteredfor the current toolselected by the toollife management feature.
Tool lifemanagement will bedisabled for thistool.
ACTIVE GROUPCANNOT BEDELETED Anattempt was madeto deletea toolgroup inthe tool life management featurethat contains an
active tool currently inthe toolholder.
ACTIVE OFFSETCANNOT CHANGE An attempt was madeto alter a tooloffset valueof a tooloffset that iscurrently theactive tool
offset onthe control. The activetool offset isindicated with an * onthe tooloffset table.
ACTIVE TOOL CANNOTBE CHANGED Anattempt was madeto edit tool datafor thecurrently active tool. De-activate thetool before
editing.
ACTIVE TOOL CANNOTBE DELETED An attempt wasmade todelete tooldata for thecurrently activetool. De-activate thetool before
editing.
ADAPTIVE FEEDMIN LIMIT Thismessage indicatesyour are exceedingthe programmeddesired torque. The actual torque
is greaterthan thedesired programmedtorque and the adaptive feedaxis has reachedthe
programmed minimum feed limit. Either raise theprogrammed desiredtorque orlower the
minimum feedlimit.
ADAPTIVE FEEDPROGRAMMING ERROR E andQ must bothbe programmedin everyG25 block.
ALL DUAL AXES AREPARKED An attempt was made, while usingdual axes, tomove thedual groupwhen allthe axesof that
group were parked.
AMP FILESIZE ERROR The sizeof the AMP filebeing downloaded is incorrect. The file cannot be downloaded.
AMP INBACKUP DOES NOTMATCH AMPIN RAM Thismessage alwaysappears after asuccessful AMP downloadif the downloadedfile is
different fromthe one currently storedin backupmemory. Its purpose is to remindthe user to
copy thedownloaded AMPinto backupmemory aftertesting it.