Manual

Error and System Messages
Appendix B
B-21
Message Description
INVALID FIXED DRILLINGAXIS The axisselected asthe drillingaxis isan invalidaxis fora drillingapplication.
INVALID FORMAT SPECIFIEDIN B/DPRNTCMD Improper format wasused inthe paramacrocommand (BPRNTor DPRNT) that outputsdata to
a peripheral device.
INVALID FUNCTION ARGUMENT An invalid paramacro argument was used in a paramacro function. The argument contains
either badsyntax or anillegal value.
INVALID G10 CODE The format fora G10 block isnot correct. Refer to your user manualfor the correct format for
the G10 block that iscurrently beingprogrammed.
INVALID IN ANGLEDWHEEL MODE A featurethat is not availablein G16.3mode, or G16.4mode or bothhas beenprogrammed.
Refer toyour grinder users manualangled-wheel grinder sectionfor a descriptionof features not
available on an angled-wheel grinder.
INVALID INFEED (PWORD) Infeedvalue (P-word) isnot in validrange. The validrange for aP-word duringa threading
cycle is whole numbers1 though4.
INVALID INPUT VALUE The dataentered isinvalid for thecurrent operation beingperformed.
INVALID INTERFERENCE AREA A G10block hasprogrammed azone wherethe plus value isless thanthe minusvalue.
INVALID INTERFERENCE CHECK AXIS An axisfrom thewrong processwas AMPed. Unless ashared axisis used in thezone, the axis
defined to make up aninterference areamust be inthe processthe zoneis definedfor.
INVALID LATHE AXIS An illegal codewas encounteredduring cylindricalinterpolation programming.
INVALID LIFE TYPE Thecurrent program is attemptingto enter aninvalid toollife typefor a tool group inthe tool
management tables. Valid toollife typesare type0, 1, or 2. Tool lifetype isprogrammed ina
G10 block following aI-word.
INVALID M99 INMAIN PROGRAM An M99part program rewind andauto start wasprogrammed in the middle of themain program.
An M99 can be programmedonly at the end of a part program.
INVALID MACRO COMMAND TheIS andIM commands arereserved foruse bythe controlonly forprogram interrupts. They
cannot be entered in a part program or MDI program.
INVALID MACRO FROMTAPE You have programmed a paramacro command that cannot beexecuted from tape.
INVALID NUMBER OFPOCKETS Thiserror occurs whenusing G10L20 toenter random tool dataand thenumber of pockets
needed for the toolis invalid.
INVALID OFFSET NUMBER An offset number out of the rangeof allowable offset numbers (eithertoo largeor too small) was
programmed.
INVALID OPERATORIN EXPRESSION Check expressionsto makesure theyare correct.
INVALID OPERATORIN PARAMACRO EXPRESSION The controlhas encountereda non-mathematicaloperator (character) ina paramacro
expression or calculate operation.
INVALID OUTPUT FORMAT An error occurredin G05DH+ communicationsblock.
INVALID PARAMACRO ARGUMENTASSIGNMENT An argument assignment ina block that calls aparamacro programcontains either aninvalid
argument specification or a syntaxerror was madein theargument.
INVALID PARAMETER NUMBER An attempt wasmade toassign orread the value of a paramacro parameter that does not exist.
INVALID PARAMETER VALUE An attempt was made toassign aninvalid value (typically toolarge ortoo small of a value)to a
paramacro parameter.
INVALID POCKET NUMBER An attempt wasmade toenter atool pocket number that exceedsthe allowablenumber of tool
pockets inthe randomtool table. This error occurswhen aP-word that is too largeor toosmall
is programmedin aG10.1L20 block.
INVALID POCKET PROFILE Aninvalid pocket profilewas programmedin alathe roughingor finishingcycle.
INVALID POSITION FBTYPE System was incorrectlyAMPed witha Yaskawa typeencoder (absolute or incremental) on the
position feedback device whenseparate positionand velocity feedback devicesare used.