Instruction Manual
Table Of Contents
- S-3056-1 Distributed Power System SA3100 Drive Configuration and Programming Instruction Manual
- Important User Information
- Contents
- List of Figures
- List of Tables
- Chapter 1 Introduction
- Chapter 2 Configuring the UDC Module, Regulator Type, and Parameters
- 2.1 Adding a Universal Drive Controller (UDC) Module
- 2.2 Entering the Drive Parameters
- 2.3 Configuring the Vector with Constant Power Regulator
- 2.4 Configuring the Volts per Hertz (V/Hz) Regulator
- 2.5 Configuring Flex I/O
- 2.6 Generating Drive Parameter Files and Printing Drive Parameters
- Chapter 3 Configuring the UDC Module’s Registers
- 3.1 Register and Bit Reference Conventions Used in this Manual
- 3.2 Flex I/O Port Registers (Registers 0-23)
- 3.3 UDC/PMI Communication Status Registers (Registers 80-89/1080-1089)
- 3.4 Command Registers (Registers 100-199/1100-1199)
- 3.5 Feedback Registers (Registers 200-299/1200-1299)
- 3.6 Application Registers (Registers 300-599, Every Scan) (Registers 1300-1599, Every Nth Scan)
- 3.7 UDC Module Test I/O Registers (Registers 1000-1017)
- 3.8 Interrupt Status and Control Registers (Registers 2000-2047)
- Chapter 4 Application Programming for DPS Drive Control
- Chapter 5 On-Line Operation
- Appendix A SA3100 Vector Regulator Register Reference
- Appendix B SA3100 Volts / Hertz Regulator Register Reference
- Appendix C SA3100 Local Tunable Variables
- Appendix D Vector with Constant Power Regulator
- Appendix E Volts per Hertz (V/Hz) Regulator
- Appendix F Status of Data in the AutoMax Rack After a STOP_ALL Command or STOP_ALL Fault
- Appendix G Torque Overload Ratio Parameter Precautions
- Appendix H Default Carrier Frequency and Carrier Frequency Limit for Drive Horsepower Ranges
- Appendix I Vector with Constant Power Parameter Entry Example
- Index
Configuring the UDC Module, Regulator Type, and Parameters
2-5
2.3 Configuring the Vector with Constant Power
Regulator
The following sections (2.3.1 to 2.3.4) describe the parameter entry screens for the
SA3100 Vector with Constant Power regulator. These screens are accessed by
selecting SA3100 as the product type and Vector with Constant Power as the
regulator type when configuring the UDC module parameters. If your drive uses the
Volts per Hertz regulator refer to section 2.4.
2.3.1 Power Module Data Screen (Vector with Constant Power)
The Power Module Data screen allows you to enter specific information about your
power system configuration and the type of Power Module being used. See figure 2.4.
Power System Configuration
• DC Input Voltage or AC input Voltage
Select the type of input line voltage (AC input or DC input) and then enter the input
voltage value.
Select DC Input Voltage if this is the DC bus voltage. Select AC Input Voltage if this
is the AC RMS voltage that is being converted to DC bus voltage. This voltage
determines which group of Power Modules may be selected from the Part Number
list. The default selection is DC Input Voltage.
• MCR Connected To Output Contactor
If you have a motor control relay (MCR) on the output of the drive (output
contactor), select this option. If there is only a manual disconnect switch and no
contactor under automatic control, do not select the output contactor option. The
default selection is no contactor.
Figure 2.4 – Power Module Data Parameter Entry Screen (Vector with Constant Power)