User Manual
Table Of Contents
- TSS-4100 Integrated TCAS, Transponder, and ADS-B Traffic Surveillance System
- TITLE PAGE
- LIST OF EFFECTIVE PAGES
- TABLE OF CONTENTS
- LIST OF ILLUSTRATIONS
- LIST OF TABLES
- INTRODUCTION
- SAFETY SUMMARY
- 1 General Information
- 2 System Components
- 2.1 INTRODUCTION.
- 2.2 COMPONENT DESCRIPTIONS.
- 2.3 ANT-42 34-54-00.
- 2.4 L-BAND ANTENNA, ANT-42, DATA.
- 2.5 ECU-3000 34-54-00.
- 2.6 EXTERNAL CONTROL UNIT , ECU-3000, DATA.
- 2.7 TDR-94D 34-54-00.
- 2.8 MODE S TRANSPONDER, TDR-94D, DATA.
- 2.9 TRE-930 34-54-00.
- 2.10 ANTENNA, TRE-930, DATA.
- 2.11 TSA-4100 34-54-00.
- 2.12 ANTENNA, TSA-4100, DATA.
- 2.13 TSS-4100 34-43-00.
- 2.14 TRAFFIC SURVEILLANCE SYSTEM, TSS-4100, DATA.
- 3 Operation
- 4 Maintenance
- 4.1 INTRODUCTION.
- 4.2 MAINTENANCE SCHEDULE.
- 4.3 CONVERSION FROM TTR/TDR TO TSS SYSTEM.
- 4.4 DATA LOADING.
- 4.5 TSS-4100 MODE S ADDRESS PROGRAMMING TOOL.
- 4.6 LED INDICATORS.
- 4.7 TEST EQUIPMENT AND POWER REQUIREMENTS.
- 4.8 TESTING AND TROUBLESHOOTING.
- 4.8.1 Pre-installation Testing.
- 4.8.2 TCAS Self Test.
- 4.8.3 Equipment Setup.
- 4.8.4 Radio Altitude System Failure Tests.
- 4.8.5 Pressure Altitude System Failure Tests.
- 4.8.6 Range and Bearing Test.
- 4.8.7 TCAS RA Test.
- 4.8.8 Transponder Tests.
- 4.8.9 ADS-B Transmit Ground Test.
- 4.8.10 Transponder/TCAS Suppression Bus Issues.
- 4.9 INITIAL INSTALLATION CHECK OUT PROCEDURE.
- 4.10 RETURN TO SERVICE TEST PROCEDURE.
- 4.11 INSPECTION/CHECK.
- APPENDIX A Faults and Warnings
- APPENDIX B Maintenance Words
- APPENDIX C Buses and Other Interfaces
- APPENDIX D Equipment Characteristics
- APPENDIX E Interconnect Diagram
- BACK COVER
maintenance 523-0 809018
• Be logged in with administrator credentials
• At least one RJ-45 port on the PC/laptop
• A Cross-Over RJ-45 Ethernet Cable.
4.5.3. P
rogramming Tool Installation.
NOTE
This program requires Microsoft™ .NET 3.5 on the PC. If there is difficulty in installing .NET, uninstall all cur-
rently installed versions of Microsoft™ .NET before attempting the new installation. Contact your network ad-
ministrator or information technology department for further assistance.
Do the steps that follow to install the Mode S Programming Tool:
a. Obtain the TSS-4100 Mode S Address Programming Tool (CPN 811-2989-001).
NOTE
This is availabl e through a CD-ROM. It may also be available through a digital download. Contact a Rockwell
Collins Product Suppor t R epresentative for more information regarding this option.
b. Open the directory with the TSS-4100 Mode S Address Programming Tool setup files.
c. If .NET is not already installed, run Install .NET 3.5 Offline.exe. If unsure whether or not .NET is installed,
proceed to the next step. This setup program is provided by Microsoft™. This setup program will indicate that it is downloading
files from the internet, and will say, "Download Complete. You can now disconnect from the Internet." These statements are
normal. All necessary files are contained within the executable.
d. Run the Mode S Tool Installation Package.msi program. Follow the prompts to install the TSS-4100 Mode S
Address Programming Tool.
NOTE
If .NET i s not installed, a prompt to download the applicable files from the Internet will show. It is recommended
to decline this download, and to perform Step 4.5.3.c. This is because the .NET framework is very large, and
downloading the files will take a significant amount of time.
4.5.4. P
rogramming Tool Setup.
Make sure the IP address of the PC or laptop is within the proper address space. If the Mode S Programming To ol is expected to be
used often, then configure an IP port, on the PC or laptop, to not get an IP address from a DNS server at start-up.
NOTE
If there are problem s setting up th e IP address of the PC or laptop, contact your ne two r k administrator or informa-
tion technology department for assistance.
a. On the TSS-4100 Mode S Address Programming Tool, select the System > IP Addresses option.
b. Select the appropriate Network Interface Card (NIC). Refer to Figure 4-2.
NOTE
In the example below, the second NIC card is being selected.
4-7