User Manual
Table Of Contents
- TSS-4100 Integrated TCAS, Transponder, and ADS-B Traffic Surveillance System
- TITLE PAGE
- LIST OF EFFECTIVE PAGES
- TABLE OF CONTENTS
- LIST OF ILLUSTRATIONS
- LIST OF TABLES
- INTRODUCTION
- SAFETY SUMMARY
- 1 General Information
- 2 System Components
- 2.1 INTRODUCTION.
- 2.2 COMPONENT DESCRIPTIONS.
- 2.3 ANT-42 34-54-00.
- 2.4 L-BAND ANTENNA, ANT-42, DATA.
- 2.5 ECU-3000 34-54-00.
- 2.6 EXTERNAL CONTROL UNIT , ECU-3000, DATA.
- 2.7 TDR-94D 34-54-00.
- 2.8 MODE S TRANSPONDER, TDR-94D, DATA.
- 2.9 TRE-930 34-54-00.
- 2.10 ANTENNA, TRE-930, DATA.
- 2.11 TSA-4100 34-54-00.
- 2.12 ANTENNA, TSA-4100, DATA.
- 2.13 TSS-4100 34-43-00.
- 2.14 TRAFFIC SURVEILLANCE SYSTEM, TSS-4100, DATA.
- 3 Operation
- 4 Maintenance
- 4.1 INTRODUCTION.
- 4.2 MAINTENANCE SCHEDULE.
- 4.3 CONVERSION FROM TTR/TDR TO TSS SYSTEM.
- 4.4 DATA LOADING.
- 4.5 TSS-4100 MODE S ADDRESS PROGRAMMING TOOL.
- 4.6 LED INDICATORS.
- 4.7 TEST EQUIPMENT AND POWER REQUIREMENTS.
- 4.8 TESTING AND TROUBLESHOOTING.
- 4.8.1 Pre-installation Testing.
- 4.8.2 TCAS Self Test.
- 4.8.3 Equipment Setup.
- 4.8.4 Radio Altitude System Failure Tests.
- 4.8.5 Pressure Altitude System Failure Tests.
- 4.8.6 Range and Bearing Test.
- 4.8.7 TCAS RA Test.
- 4.8.8 Transponder Tests.
- 4.8.9 ADS-B Transmit Ground Test.
- 4.8.10 Transponder/TCAS Suppression Bus Issues.
- 4.9 INITIAL INSTALLATION CHECK OUT PROCEDURE.
- 4.10 RETURN TO SERVICE TEST PROCEDURE.
- 4.11 INSPECTION/CHECK.
- APPENDIX A Faults and Warnings
- APPENDIX B Maintenance Words
- APPENDIX C Buses and Other Interfaces
- APPENDIX D Equipment Characteristics
- APPENDIX E Interconnect Diagram
- BACK COVER
maintenance 523-0809018
Figure 4-7. TSS-4100 Front Panel LEDs
Table 4-3. LED Descriptions
Indicator Color Description
LRU STATUS indicator will light green whenever the self-test is successful. The LRU
STATUS indicator will light red whenever the self-test fails.
LRU STATUS RED/GREEN
If this is red, it is probable that the TSS will need to be replaced. See the maintenance
words for more information on this.
UPPER ANT FAIL indicator will light red whenever the impedance of the upper
antenna does not meet specification.
UPPER ANT FAIL RED
If this is lit the cabling from the TSS to the upper antenna needs to b e checked.
LOWER ANT FAIL indicator will light red whenever the impedance of the l ower
antenna does not meet specification.
LOWER ANT
FAIL
RED
If this is lit the cabling from the TSS to the lower antenna needs to be checked.
CONTROL INPUT indicator will light whenever a fault with the control panel is
detected.
CONTROL I NPUT RED
If this is lit the conn ection between the TSS and the selected control p anel needs to
be checked. Alternately, check the control panel selection discretes and verify they
are correctly being set.
4-12