Operating instructions

16V CORDLESS DRILL / DRIVER ENG
10
TECHNICAL DATA
Charger voltage 120 V~ 6 0 Hz
Rated voltage 16 V
Max*
Nominal voltage 14 .4 V
No load speed 0 -3 5 0 /0 -13 5 0 /min
Number of clutch positions 15 + 1
Max torque 26 5 in-lbs
Chuck capacity 3 /8 ˝
Max. drilling capacity Steel 3 /8 ˝
Wood 1˝
Machine weight 2.7 lbs
* Voltage measured without workload. Initial battery
voltage reaches maximum of 16 volts. Nominal voltage
is 14 .4 volts.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
WARNING: Us e c la m p s o r a n o th e r p ra c tic a l
w a y to s e c u re a n d s u p p o r t th e w o rk p ie c e
to a s ta b le p la tfo rm . Ho ld in g th e w o rk b y h a n d o r
a g a in s t y o u r b o d y le a v e s it u n s ta b le a n d m a y le a d
to lo s s o f c o n tro l.
1. TO REMOVE OR INSTALL BATTERY PACK
(Se e Fig . A1, A2)
Depress the Battery Pack Release Button (7 ) to release
and slide the Battery Pack (8 ) out from your tool. After
recharge, slide it back into your tool. A simple push and
slight pressure will be sufficient.
2. HOW TO USE THE HOOK (Se e Fig . B1, B2)
Screw the HOOK on the tool with the screw provided in
the plastic bag. The HOOK (6 ) can be hooked on your belt
or pocket, etc.
3. ON/OFF SWITCH (Se e Fig . C)
Depress the On/Off switch (9 ) to start and release it to
stop your drill. The On/Off Switch is fitted with a brake
function which stops your Chuck immediately when you
quickly release the switch.
It is also a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
WARNING: Do n o t o p e ra te fo r lo n g p e rio d s
a t lo w s p e e d b e c a u s e e x c e s s h e a t w ill b e
p ro d u c e d in te rn a lly .
4. SWITCH LOCK
The On/off Switch (9 ) can be locked in the OFF position.
This helps to reduce the possibility of accidental starting
when not in use. To lock the On/off Switch, place the
Rotation Control in the center position.
5. REVERSIBLE (Se e Fig . D1, D2)
For drilling and screw driving use forward rotation
marked “
” (lever is moved to the left). Only use
reverse rotation marked “
” (lever is moved to the
right) to remove screws or release a jammed drill bit.
WARNING: Ne v e r c h a n g e th e d ire c tio n o f
ro ta tio n w h e n th e Ch u c k is ro ta tin g , w a it
u n til it h a s s to p p e d !
47/30%%$'%!2#/.42/,3EE&IG%
The drill has a Two-Speed Gear Control (3 ) designed
for drilling or driving at LO (mark is 1) or HI (mark is 2)
speeds. A slide switch is located on top of the drill to
select either LO or HI speed. When using the drill in the
LO speed range, the speed will decrease and the drill will
have greater power and torque. When using the drill in
the HI speed range, the speed will increase and the drill
will have less power and torque.
Ge a r I
Low speed range: for screwdriving or working with large
drilling diameter
Ge a r II
High speed range: for working with small drilling
diameter
WARNING: To p re v e n t g e a r d a m a g e , a lw a y s
a llo w th e c h u c k to c o m e to a c o m p le te s to p
b e fo re c h a n g in g th e d ir e c tio n o f ro ta tio n .
7. CHUCK ADJUSTMENT (Se e Fig . F)
With the chuck facing you, rotate the chuck
counterclockwise to open the jaws. Insert the drill bit
between the chuck jaws. Rotate the chuck clockwise to
tighten the jaws. Insure that the drill bit is seated in the
center of the jaws.
8. TORQUE ADJUSTMENT (Se e Fig . G)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the Torque Adjustment
Ring (2). The torque is greater when the Torque
Adjustment Ring is set on a higher setting. The torque is
less when the Torque Adjustment Ring is set on a lower
setting.
Make the setting as follows: