INSTRUCTION MANUAL www.rodemic.com 117-950-3-1-HS1_manual.
117-950-3-1-HS1_manual.
INTRODUCTION Thank you for investing in the RØDE HS1 Headset microphone. Whether you’re presenting for television or live on-stage, in a 20,000 seat auditorium or in a house of worship, RØDE has your needs covered with the reliable and intuitive HS1. Featuring the pure, clear audio and low handling noise that RØDE is celebrated for, the HS1 Headset is built to deliver and to last.
F E AT U R E S ERGONOMIC DESIGN • • • • • • Ultra discreet appearance Three axes of mechanical adjustment for perfect fit Malleable tube arm and headband for fine adjustment Ultra lightweight construction for complete comfort Right or left side configuration Incorporated cable management system HIGH QUALITY PERFORMANCE • • • • Ø3.4 mm (Ø0.
H S1 & ACC E S S O R I E S 1. 2. 3. 4. 5. 6. 7. 8. RØDE HS1 Headset Anti-trauma water resistant storage case Water resistant pop filter Mini-furry for high wind protection Shielded, detachable Kevlar® reinforced cable Lapel-style cable management clip Adjustment tools Sanitary cleansing wipes Compact, interchangeable MiCon™ adaptors available to suit industry standard wireless systems* 2. 4. 5. 3. 6. 1. 7. 8. *MiCon™ adaptors sold separately - see rodemic.
S PEC I F I C AT I O N S Acoustic Principle: Permanently polarised condenser Directional Pattern: Omni-directional (see graph) Frequency Range: 60 Hz ~ 18 KHz (see graph) Output Impedence: 3k Ω Typical Signal To Noise Ratio: 58 dBA Equivalent Noise: 36 dBA SPL (per IEC651) Clipping SPL: 122 dB Maximum Output: 189 mV** Sensitivity: -47.
S PEC I F I C AT I O N S FREQUENCY RANGE 20 dB re 1 V/Pa 10 0 -10 -20 -30 20Hz 100 1000 10 000 20 000 POLAR RESPONSE +5.0 0.0 -2.0 -4.0 -6.0 -8.0 -10.0 -12.0 -14.0 -16.0 -18.0 -20.0 -22.0 -24.0 -2.0 -10.0 -20.0 -25.0 dB rel. 1V/Pa Frequency: 500 Hz: 1000 Hz: 4000 Hz: ** Calculated from maximum SPL peak before clipping. All measurements are calculated when powered at 5V or P48 (RØDE XLR adaptor) -7- 117-950-3-1-HS1_manual.
H S1 S T R U C T U R E CABLE CONTROL TAB MiCon™ CONNECTION HEADBAND RETAINER MOISTURE CONTROL BELT MICROPHONE WITH POP FILTER EAR HOOK RETAINER CAP HEADBAND SIZE ADJUSTMENT TAB -8- 117-950-3-1-HS1_manual.
M I C PL AC EM EN T For the best performance, the HS1 microphone should be positioned just at the corner of the mouth, as close as possible without being in front of the user’s mouth. This ensures that the mic is in close proximity to the sound source without being exposed to possible plosives (gusts of wind noise caused by hard sounds such as ‘p’ or ‘t’.) -9- 117-950-3-1-HS1_manual.
FI T T I N G YO U R H S1 The RODE HS1 has been designed with complete adjustability in mind, ensuring maximum comfort and security of fit for each user. Three axes of movement configure the microphone placement for optimal audio quality. To custom fit the HS1, you may wish to try on the microphone first. Hook the headband over your ears and the size of the headband can be controlled by pushing or pulling the left and right tabs along the rear of the headset.
FI T T I N G YO U R H S1 ADJUST THE HEIGHT OF THE HS1 To place the retainer at the ideal position just below and behind the ear lobe, change the position of the retainer on the headband wire. To re-position, loosen the retainer cap using the screwdriver provided in your HS1 case. You will not need to unscrew the retainer cap completely to allow movement. Once satisfied with the height of the retainer on the headband, tighten the retainer cap back in place.
FI T T I N G YO U R H S1 PIVOT THE HS1 You may adjust the proximity of the microphone to your mouth by pivoting the mic. Push the microphone up or down at the retainer to create a rotating movement until you find the angle that positions the HS1 microphone closest to your mouth. 300 degrees of rotation allows for the best possible positioning. Pivot the HS1 in a rotating movement - 12 - 117-950-3-1-HS1_manual.
FI T T I N G YO U R H S1 ADJUST THE LENGTH OF THE HS1 If the HS1 is extending beyond your mouth, or is not in close enough proximity to it, you may alter the length by pushing or pulling the body through the retainer. Firstly, ensure the retainer cap has been loosened, but not removed completely. Hold the mic body at the connector end and twist 90° (1/4 turn) to unlock it from the retainer clasp. The push/pull motion is controlled by friction so apply a little force if required.
FI T T I N G YO U R H S1 L E F T / R I G H T C O N F I G U R AT I O N O F H S 1 Depending on personal preference, the HS1 can sit at either the left or right hand side of the mouth. To change left/right configuration, unscrew the retainer cap completely using the screwdriver provided. (This is best done over a table or work surface to ensure no parts are misplaced). Ease the microphone to the left and right until it releases from the headband wire completely.
FI T T I N G YO U R H S1 RETAINER CAP Re-position the HS1, then screw the retainer cap back into place ERGONOMIC ADJUSTMENT For further ergonomic adjustment, you may bend the microphone tube along the body and adapt its shape. This allows the microphone to suit the contours of an individual face for complete compatibility with the wearer. Note: The HS1 tube arm is designed to be resilient and malleable for optimal adjustment.
CO N N EC TO R A N D C A B L E The HS1’s connections have been designed using the RØDE MiCon™ connector system, which provides seamless integration with a wide range of wireless systems for your convenience, while maintaining the headset’s discreet appearance. (MiCon™ adaptors sold separately – see rodemic.com/hs1 for a full list of compatibility) To connect the HS1 to your MiCon™ cable, screw either end of the cable to the MiCon™ connection at the end of the microphone tube.
CO N N EC TO R A N D C A B L E Then, attach the corresponding adaptor for your wireless system to the remaining connection on your MiCon™ cable, and plug in to your wireless system (MiCon™ adaptors sold separately). For further management, excess cable can be threaded through the groove in the cable management clip provided. Loop through the peg as many times as necessary, and peg to the user’s clothing.
I N C LU D E D ACC E S S O R I E S W AT E R R E S I S TA N T P O P F I LT E R The pop filter is an optional attachment to your HS1 which reduces plosives (gusts of wind noise caused by hard sounds such as ‘p’ or ‘t’.) It is also strongly recommended you use your pop filter to protect the HS1 in any extreme environments which are overly dusty or moist to prevent damage to the mic. To correctly fit your pop filter, slide the filter over the microphone head until it reaches the first groove.
I N C LU D E D ACC E S S O R I E S MINI-FURRY For increased wind protection, a mini-furry windshield is provided with the HS1. The windshield is ideal for situations such as outdoor performances, where wind noise may distort the audio quality of the mic. To fit, simply slide the mini-furry over the microphone head until it reaches the first groove. Ensure the fur is fluffed up in all directions for maximum effectiveness. Mic with mini-furry - 19 - 117-950-3-1-HS1_manual.
S TO R AG E A N D C A R E When not in use, always keep your HS1 in the storage case provided. Close and snap the storage case for complete protection. If you find you cannot open the case even after snapping open the clips (for example following a flight), turn the dial at the front of the case slowly, in the direction marked ‘open’. This will equalise the air pressure in the case and allow it to open. - 20 - 117-950-3-1-HS1_manual.
S TO R AG E A N D C A R E Inside the case, you will find a sachet of moisture absorbent crystals. Please retain these crystals and store with the HS1 to keep the microphone in ideal condition. Eventually this pack of crystals will need to be dried. This is indicated by the crystals turning pink in colour. They can easily be re-used by placing them in an oven at 100-150 degrees Celsius for approximately ten minutes. The crystals will operate effectively again once they have turned blue.
117-950-3-1-HS1_manual.
S U PP O R T If you experience any problem, or have questions regarding your microphone, first contact the dealer who sold it to you. We have an extensive dealer network to assist you. If you have difficulty getting the advice or assistance you require from the dealer, do not hesitate to contact us directly via the details below. I N T E R N AT I O N A L 107 Carnarvon Street Silverwater NSW 2128 Australia Ph: +61 2 9648 5855 Fax: +61 2 9648 2455 USA P.O.
117-950-3-1-HS1_manual.
