INSTALLATION GUIDE 1-Channel Power Amplifier / 2-Channel Power Amplifier 4-Channel Power Amplifier R1500-4100A2 Manual.indd 1 07.07.
INHALTSVERZEICHNIS / CONTENTS Seite 1. 2. 2.1 3. 3.1 3.2 3.3 3.4 4. 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.4 4.5 6. 6. TECHNISCHE MERKMALE . . . . . . . . . . . . . . . . . . . . . . . . 4 EINGÄNGE-AUSGÄNGE-BEDIENUNGSELEMENTE . . 5-8 MONTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WAHL DES EINBAUORTES . . . . . . . . . . . . . . . . . . . . . . . 9 ELEKTRISCHER ANSCHLUSS . . . . . . . . . . . . . . . . . . . . . 9 VERLEGEN VON CINCHKABEL / REMOTE-KABEL . . .
1- / 2- AND 4-CHANNEL POWER AMPLIFIER Herzlichen Glückwunsch! Wir gratulieren Ihnen zum Kauf dieser RODEK Car-Hifi Endstufe. Damit Sie die Wiedergabequalität und die Leistungsfähigkeit dieses Verstärkers voll ausschöpfen können, bitten wir Sie, sich eingehend mit den Möglichkeiten und technischen Features dieses Car-Amps vertraut zu machen. Lesen Sie deshalb die nachfolgenden Abschnitte sorgfältig durch und bewahren Sie diese Bedienungsanleitung für eventuell später auftauchende Fragen auf.
TECHNISCHE MERKMALE ■ Car-Hifi Verstärker zur Realisierung eines einbaufreundlichen, leistungs- und klangstarken System Konzeptes ■ Phase Shift Control, variabel zwischen 0-180° ■ Zwei MOSFET Netzteile (R4100A2 / R2180A2) sorgen für kräftige Ausgangsleistung und hohe Stabilität ■ Innovatives Gehäusedesign mit Clam-Shell Aluprofil Kühlkörper und innenliegendem, temperaturgesteuertem Lüfter ■ 2 Ohm Last-Stabilität aller Kanäle, jedes Kanalpaar lässt sich im Brückenmodus betreiben ■ Massive gekapselte An
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE 1. Cinch Eingangsbuchsen (CH1/CH2, CH3/CH4; jeweils immer linker und rechter Kanal). NF-Signal Eingang für den Anschluss der Cinch-Ausgänge des Steuergerätes 9. Regler zum Einstellen der Tiefpass-Trennfrequenz der Kanäle CH3/4 (LOWPASS) an der integrierten elektronischen Frequenzweiche 2. Eingangsempfindlichkeitsregler - LEVEL - des Kanalpaares CH1/2 für die Anpassung an die Ausgangsspannung des Steuergerätes 10.
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL R2100A2 R2180A2 REAR PANEL R2100A2 R2180A2 A B Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom) 6 R1500-4100A2 Manual.indd 6 07.07.
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL R4100A2 REAR PANEL R4100A2 A B Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom) 7 R1500-4100A2 Manual.indd 7 07.07.
1. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL R1500A R1500A2 REAR PANEL R15000A A R1500A2 B Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom) 8 R1500-4100A2 Manual.indd 8 07.07.
2. MONTAGE Bevor Sie mit der Montage beginnen, erstellen Sie am besten eine kurze Anschluss- und Installationsskizze. Beachten Sie bitte, dass die Kabelführung und der gewählte Massepunkt einen entscheidenden Einfluss auf das störungsfreie Funktionieren Ihrer Anlage hat.
3. ELEKTRISCHER ANSCHLUSS Speziell die musiksignalführenden (Cinch-) Kabel müssen soweit wie möglich von allen potentiellen "elektrischen Störsendern" wie Bordcomputer, Benzinpumpe, Kabelbäumen, Stromversorgungskabel für die Beleuchtung, etc. verlegt werden! 3.1 VERLEGEN VON CINCHKABEL / REMOTE-KABEL Verlegen Sie nun das (oder die) Cinchkabel und das Remote-Kabel vom Steuergerät zur Endstufe. Diese Kabel sollten unbedingt räumlich getrennt von der Stromzuführung des Verstärkers eingezogen werden.
Systemkonfiguration R1500A2 / R2100A2 / R2180A2 R2100A2 R2180A2 OPERATION MODE SELECTOR CH1/2 set to HP R1500A2 R2100A2 R2180A2 ohms R1500A2 min. 2 ohms OPERATION MODE SELECTOR CH1/2 set to BP 11 R1500-4100A2 Manual.indd 11 07.07.
Systemkonfiguration R1500A2 / R2100A2 / R2180A2 / R4100A2 OPERATION MODE SELECTOR CH1/2 set to BP OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to BP R1500A2 R2100A2 R2180A2 R4100A2 ohms R1500A2 min. 2 ohms 12 R1500-4100A2 Manual.indd 12 07.07.
Systemkonfiguration R4100A2 CH1 CH2 CH3 CH4 R4100A2 MID/ WOOFER MID/ WOOFER MID/ WOOFER MID/ WOOFER OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to HP 13 R1500-4100A2 Manual.indd 13 07.07.
Systemkonfiguration R4100A2 R4100A2 OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to BP ohms 14 R1500-4100A2 Manual.indd 14 07.07.
Systemkonfiguration R4100A2 R4100A2 OPERATION MODE SELECTOR CH1/2 set to HP CH3/4 set to BP 15 R1500-4100A2 Manual.indd 15 07.07.
4. EINSTELLUNG DER INTEGRIERTEN FREQUENZWEICHEN 4.1 MINIMALE LASTIMPEDANZ Die RODEK Verstärker sind von der Auslegung der Endtransistoren-Sektion auf eine sehr hohe Ausgangsleistung im 4 und 2 Ohm stereo Betrieb ausgelegt, sie bieten hier eine gemessen am Preis überdurchschnittliche Performance. Die RODEK Verstärker können auf eine 4 Ohm Last gebrückt werden. Im Stereobetrieb darf die minimale Abschlussimpedanz von 2 Ohm pro Kanal auf keinen Fall unterschritten werden.
4. EINSTELLUNG DER INTEGRIERTEN FREQUENZWEICHEN 4.3.2 BANDPASS FÜR KICKBASS SYSTEME Für den Betrieb von Kickbässen kommen zwei Filter, die nacheinander geschaltet sind, zum Einsatz. Der Weichenzweig läuft also im Bandpass Modus, entsprechend einem Hochpass (10-400Hz) mit nachgeschaltetem Tiefpass (30-400 Hz). Das Hochpassfilter wird in der Regel um mindestens Faktor zwei kleiner eingestellt, wie die nachfolgende Tiefpass-Trennfrequenz.
4. EINSTELLUNG DER INTEGRIERTEN FREQUENZWEICHEN 4.4 ANPASSUNG DER EINGANGSEMPFINDLICHKEIT Die korrekte Eingangsempfindlichkeitseinstellung ist wichtig für die Ausnutzung des optimalen Dynamikspielraumes Ihrer Steuergerät / Verstärker / Lautsprecherkombination. Diese Empfindlichkeitseinstellung beeinflusst das Grundrauschen ebenso wie die verzerrungsfrei erzielbare Maximallautstärke. Schalten Sie das Steuergerät ein. Stellen Sie nun den Lautstärkeregler Ihres Steuergerätes auf ca.
Congratulations! and thank you for choosing this RODEK Car Audio Power Amplifier! To maximize the performance of your complete car audio system, it is recommended that you acquaint yourself thoroughly with the capabilities and features of this amplifier. Therefore read this manual carefully, before attempting the installation of this multichannel amplifier and retain the manual and your purchasing/installation receipts for future reference. 19 19 R1500-4100A2 Manual.indd 19 07.07.
TECHNICAL FEATURES ■ Car audio amplifier for a compact and user friendly realization of a powerful car audio system ■ Two independent MOSFET power supplies (R4100A2 / R2180A2) for high power output and best stability into low impedance loads ■ Versatile integrated electronic crossovers with filter slopes of 12/dB/octave. Independently selectable operation modes: Highpass, bandpass and fullrange.
1. INPUTS - OUTPUTS - CONTROLS 1. RCA inputs (CH1/2, CH3/4, left and right channels), Line inputs for connection with RCA line-out’s of the head-unit 2. Input gain control, LEVEL adjustment for channels CH1/2. Used to match the RCA line output voltage of the head-unit to the amplifier input section. 3. Operation mode selector, slide switch to select Highpass, Bandpass or Fullrange operation of the active crossover for channels CH1/2 4.
1. INPUTS - OUTPUTS - CONTROLS FRONT PANEL R2100A2 R2180A2 REAR PANEL R2100A2 R2180A2 A B Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom) 22 R1500-4100A2 Manual.indd 22 07.07.
1. INPUTS - OUTPUTS - CONTROLS FRONT PANEL R4100A2 REAR PANEL R4100A2 A B Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom) 23 R1500-4100A2 Manual.indd 23 07.07.
1. INPUTS - OUTPUTS - CONTROLS FRONT PANEL R1500A R1500A2 REAR PANEL R15000A A R1500A2 B Amplifier internal ventilation A = air inlets (top) B = air outlets (bottom) 24 R1500-4100A2 Manual.indd 24 07.07.
2. MOUNTING OF THE AMPLIFIER Before you attempt the installation of your RODEK amplifier, it is recommended to map out the complete audio system and the respective wiring required. Please note that - because of possible interference problems with the existing car electrics and electronics - especially the routing of the signal cables and the chassis ground connection will have a profound impact on the performance of the overall system.
3. ELECTRICAL WIRING Especially the music signal cables (RCA interconnects) should be kept far away from any potential sources of electrical interference i.e. electronic vehicle management systems (engine computers, relays etc.) fuel pumps, wiring harnesses etc.! 3.1 RCA INTERCONNECTS / REMOTE LEAD Carefully run the RCA audio signal interconnect(s) and the remote switching cable from the head-unit to the amplifier. The audio signal cables should be routed completely separate from the power cables.
4. CROSSOVER SETTINGS 4.1 MINIMUM IMPEDANCE LOAD The output stages of the RODEK amplifiers are designed to give you extraordinary output power into 4 or 2 ohms loads in normal stereo configurations. In bridged mode, the minimum impedance load is 4 ohms. The amplifier might suffer from thermal shut-down or even damage, if these recommended minimum impedance load ratings are not considered appropriately. The R1500A2 is stable into 2 ohms. 4.
4. CROSSOVER SETTINGS 4.2.2 BANDPASS FOR KICKBASS SYSTEMS If you intend to operate a kickbass loudspeaker system in the front doors of your vehicle, you must select two crossover frequencies at the active crossover of your RODEK amplifier. The operation mode must be set to bandpass. The bandpass filter contains a highpass (10 - 400Hz) with a cascaded lowpass (30 - 400Hz) filter.
4. CROSSOVER SETTINGS Turn-on your head-unit and set the volume control to approximately 3/4 of full volume, while playing a dynamic track from a CD. Slowly increase the LEVEL adjustment control of the channel pair, to which your subwoofer system is connected to. Turn up the (sub channel) level control knob until you can just about hear distorted bass sounds.
5. TECHNICAL SPECIFICATIONS R4100A2 R2180A2 R2100A2 R1500A2 Rated Power Output (RMS) All channels driven simultaneously @ 13.8 V into 4 Ohms (THD<0.1%) 4x85W 2x185W 2x105W 1x355W Rated Power Output (RMS) All channels driven simultaneously @ 13.8 V into 4 Ohms (THD<1%) 4x95W 2x190W 2x110W 1x375W Rated Power Output (RMS) All channels driven simultaneously @ 13.8 V into 2 Ohms (THD<1%) 4x140W 2x310W 2x150W 1x555W Rated Power Output (RMS) All channels driven simultaneously @ 13.
6. WARRANTY Thank you for purchasing this RODEK amplifier. It is advisable to keep the original packing material for future transporting of the product. Please read the warranty specifications below carefully. Should your RODEK product require warranty service, please return it to the retailer from whom it was purchased, or the distributor in your country. Please do not send any product to RODEK Inc. U.S.A.
4.