I N S TA L L AT I O N G U I D E 1/2/4/5-CH Power Amplifiers RN-1600 RN-2160 RN-4110 RN-460-200 NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 1 09.05.
INHALTSVERZEICHNIS 1. EINLEITUNG ............................................................................................................................................ 3 2. 2.1 2.2 2.3 2.4 EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE ............................................................................ 4-9 MODELL RN1600 .....................................................................................................................................................................
1. EINLEITUNG Herzlichen Glückwunsch! Wir gratulieren Ihnen zum Kauf dieser RODEK Endstufe. Damit Sie die Wiedergabequalität und die Leistungsfähigkeit dieses Verstärkers voll ausschöpfen können, bitten wir Sie, sich eingehend mit den Möglichkeiten und technischen Features dieses Car-Amps vertraut zu machen. Lesen Sie deshalb die nachfolgenden Abschnitte sorgfältig durch und bewahren Sie diese Bedienungsanleitung für eventuell später auftauchende Fragen auf.
2. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE FRONT PANEL RN-1600 FRONT PANEL RN-2160 4 NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 4 09.05.
NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 5 09.05.
2. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE 2.1 MODELL RN-1600 9. Maxi Sicherung für die Absicherung des Netzteils der Endstufe Cinch Ausgangsbuchsen (CH L + CH R; jeweils immer linker und rechter Kanal). Gepufferter NF-Signal Ausgang für das weiterleiten des Eingangssignales an eine weitere Endstufe 10. "+ 12 V" Anschlussterminal für den Anschluss der Endstufe an den Pluspol der Autobatterie über eine Haupt-Sicherung 2. Cinch Eingangsbuchsen (CH L + CH R; jeweils immer linker und rechter Kanal).
2. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE 2.2 MODELL RN-2160 9. Anschlussterminal für ein Paar Lautsprecher im stereo Modus oder gebrückt Cinch Eingangsbuchsen (CH L + CH R; jeweils immer linker und rechter Kanal). NF-Signal Eingang für den Anschluss der Cinch-Ausgänge des Steuergerätes 10. ATC Sicherungen für die Absicherung des Netzteils der Endstufe 2. Eingangsempfindlichkeitsregler – LEVEL – des Kanalpaares CH1 + CH2; für die Anpassung der Endstufe an die Ausgangsspannung des Steuergerätes 11.
2. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE 2.3 MODELL RN-4110 1. Cinch Ausgangsbuchsen (CH L + CH R; jeweils immer linker und rechter Kanal). Gepufferter NF-Signal Ausgang für das weiterleiten des Eingangssignales an eine weitere Endstufe 2. Eingangsempfindlichkeitsregler – LEVEL – des Kanalpaares CH3 + CH4; für die Anpassung der Endestufe an die Ausgangsspannung des Steuergerätes 3.
2. EINGÄNGE - AUSGÄNGE - BEDIENUNGSELEMENTE 2.4 MODELL RN-460-200 1. Cinch Eingangsbuchsen CH5. NF-Signal Eingang für den Anschluss der Cinch-Ausgänge des Steuergerätes 11. "+ 12 V" Anschlussterminal für den Anschluss der Endstufe an den Pluspol der Autobatterie über eine Haupt-Sicherung 2. Cinch Eingangsbuchsen (CH3 + CH4; jeweils immer linker und rechter Kanal). NF-Signal Eingang für den Anschluss der Cinch-Ausgänge des Steuergerätes 12. "REM" Anschlussterminal für die Ein- bzw.
3. MONTAGE Bevor Sie mit der Montage beginnen, erstellen Sie am besten eine kurze Anschluss- und Installationsskizze. Beachten Sie bitte, dass die Kabelführung und der gewählte Massepunkt einen entscheidenden Einfluss auf das störungsfreie Funktionieren Ihrer Anlage hat.
4. ELEKTRISCHER ANSCHLUSS ACHTUNG! Entfernen Sie vor Beginn der Arbeiten immer das Minuskabel von entsprechenden Pol der Batterie !! Bei allen nachfolgend beschriebenen Installationsschritten muss der Stromkreis des Kraftfahrzeugs unterbrochen sein! Erst nach Abschluss aller Installationsarbeiten wird über das Massekabel der Stromkreis wieder geschlossen. Der Stromkabelquerschnitt der Plus- und Minusleitung (bei einer Kabellänge von ca. 5m) sollte mindestens 20mm², besser jedoch 35mm² betragen.
4. ELEKTRISCHER ANSCHLUSS 4.2 VERLEGEN VON CINCHKABEL / REMOTE-KABEL Verlegen Sie nun das (oder die) Cinchkabel und das RemoteKabel vom Steuergerät zur Endstufe. Diese Kabel sollten unbedingt räumlich getrennt von der Stromzuführung des Verstärkers eingezogen werden. Verwenden Sie mindestens doppelt oder besser dreifach geschirmte Cinch-Kabel! Schließen Sie das Remote-Kabel an die mit „REM“ bezeichnete Klemme an der Endstufe und an das mit "Amplifier-Rem." bezeichnete Kabel Ihres Steuergerätes an.
5. EINSTELLUNG DER FREQUENZWEICHE Satelliten-System in den Vordertüren, empfohlene Trennfrequenz Hochpass: 10 cm Koax- oder Komponentensysteme 13 cm Koax- oder Komponentensysteme 16 cm Koax- oder Komponentensysteme 90 – 120 Hz 80 – 100 Hz 60 – 90 Hz Satelliten-System in den Hintertüren oder der Heckablage, empfohlene Trennfrequenz Hochpass: 10 cm Koax- oder Komponentensysteme 13 cm Koax- oder Komponentensysteme 16 cm Koax- oder Komponentensysteme 100 – 150 Hz 120 – 150 Hz 130 – 150 Hz 5.
5. EINSTELLUNG DER FREQUENZWEICHE 5.5 ANPASSUNG DER EINGANGSEMPFINDLICHKEIT Die korrekte Eingangsempfindlichkeitseinstellung ist wichtig für die Ausnutzung des optimalen Dynamikspielraumes Ihrer Steuergerät / Verstärker / Lautsprecherkombination. Diese Empfindlichkeitseinstellung beeinflusst das Grundrauschen ebenso wie die verzerrungsfrei erzielbare Maximallautstärke. Schalten Sie das Steuergerät ein. Stellen Sie nun den Lautstärkeregler Ihres Steuergerätes auf ca.
6. TECHNISCHE SPEZIFIKATIONEN RN-1600 RN-2160 RN-4110 RN-460-200 1-Kanal (Mono) 2-Kanal 4-Kanal 5-Kanal 195 Wrms x 1 @ 4 Ω (<0.1 %*) 205 W x 1 @ 4 Ω (<1.0 %*) 300 Wrms x 1 @ 2 Ω (<0.1 %*) 350 W x 1 @ 2 Ω (<1.0 %*) 500 W x 1 @ 1 Ω (<1.0 %*) 145 Wrms x 2 @ 4 Ω (<0.1 %*) 155 W x 2 @ 4 Ω (<1.0 %*) 480 W x 1 @ 4 Ω (<1.0 %*) 240 W x 2 @ 2 Ω (<1.0 %*) 100 Wrms x 4 @ 4 Ω (<0.1 %*) 105 W x 4 @ 4 Ω (<1.0 %*) 300 W x 2 @ 4 Ω (<1.0 %*) 150 W x 4 @ 2 Ω (<1.
CONTENTS 1. INTRODUCTION ..................................................................................................................................... 17 2. 2.1 2.2 2.3 2.4 INPUTS – OUTPUTS - CONTROLS..................................................................................................... 18-23 MODEL RN-1600 .....................................................................................................................................................................
1. INTRODUCTION Congratulations! And thank you for choosing this RODEK Power Amplifier! To maximize the performance of your complete car audio system, it is recommended that you acquaint yourself thoroughly with the capabilities and features of this amplifier. Therefore read this manual carefully, before attempting the installation of this amplifier and retain the manual and your purchasing/installation receipts for future reference. 17 NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 17 09.05.
2. INPUTS – OUTPUTS – CONTROLS FRONT PANEL RN-1600 FRONT PANEL RN-2160 18 NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 18 09.05.
2. INPUTS – OUTPUTS – CONTROLS FRONT PANEL RN-4110 FRONT PANEL RN-460-200 19 NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 19 09.05.
2. INPUTS – OUTPUTS – CONTROLS 2.1 MODEL RN-1600 1. 2. RCA line outputs (CH L + CH R; left and right channels). Line outputs to pass-thru the input signal to another amp RCA line inputs (CH L + CH R; left and right channels). Line inputs for connection of the amp to the RCA lineouts of the head unit 3. Input gain control. LEVEL adjustment for channels CH L + CH R. Used to match the RCA line output voltage of the head unit to the amplifier input section 4. Bass EQ control.
2. INPUTS – OUTPUTS – CONTROLS 2.2 MODEL RN-2160 1. RCA line inputs (CH1 + CH2; left and right channels). Line inputs for connection of the amp to the RCA lineouts of the head unit 10. ATC fuses to protect the power supply of the amplifier from damage 11. “+12V” for connection to the positive terminal of car battery 2. Input gain control. LEVEL adjustment for channels CH1 + CH2. Used to match the RCA line output voltage of the head unit to the amplifier input section 12.
2. INPUTS – OUTPUTS – CONTROLS 2.3 MODEL RN-4110 1. 2. 3. 4. 5. 6. RCA line outputs (CH L + CH R; left and right channels). Line outputs to pass-thru the input signal to another amp Input gain control. LEVEL adjustment for channels CH3 + CH4. Used to match the RCA line output voltage of the head unit to the amplifier input section Bass EQ control.
2. INPUTS – OUTPUTS – CONTROLS 2.4 MODEL RN-460-200 1. 2. RCA line inputs (CH5; left and right channels). Line inputs for connection of the amp with RCA line-outs of the head unit RCA line inputs (CH3 + CH4; left and right channels). Line inputs for connection of the amp with RCA line-outs of the head unit 11. “+12V” for connection to the positive terminal of car battery 12. “REM” for the automatic (remote) turn-on / turn-off of the power amplifier from the head unit's amplifier remote wire 13.
3. MOUNTING Before you attempt the installation of your RODEK amplifier, it is recommended to map out the complete audio system in your vehicle and the respective wiring required. Please note that - because of possible interference problems with the existing car electrics and electronics - especially the routing of the signal cables and the chassis ground connection will have a profound impact on the performance of the overall system.
4. ELECTRICAL WIRING IMPORTANT! Disconnect the negative battery terminal (-12V) or remove the main fuse near the car battery before you start any wiring work! The power supply of the car audio system must be disconnected until the entire wiring and installation is completed. The recommended minimum power cable cross-section of the main power supply cable is 20mm², but if you drive the amp very hard, or you have multi amplifier setup, a 35mm² power cable is recommended.
4. ELECTRICAL WIRING 4.2 ROUTING AND CONNECTION OF RCA INTERCONNECTS / REMOTE LEAD Carefully run the RCA audio signal interconnect(s) and the remote switching cable from the head unit to the amplifier. The audio signal cables should be routed completely separate from the power cables. Use only double or triple shielded quality cables! Connect the remote wire lead to the remote output of the head unit and to the remote input terminal of the amplifier.
5. CROSSOVER SETTINGS 5.1 SELECTING THE OPERATION MODE The RODEK amplifiers feature an active crossover section with full versatility and thus, offer different amplification modes, which can be set by the operation mode slide switch(es). The operation mode switch enables you to configure each stereo channel pair to work in either in full range, high pass or even band pass mode.
5. CROSSOVER SETTINGS 5.3 BANDPASS FOR KICKBASS SYSTEMS If you intend to operate a kick bass loudspeaker system in the front doors of your vehicle, you must select two crossover frequencies at the active crossover of your RODEK amplifier. The operation mode must be set to band pass. The band pass filter contains a high pass with a cascaded low pass filter. The low pass crossover point is usually set at a frequency that equals approx. twice the value of the high pass crossover setting.
5. CROSSOVER SETTINGS 5.5 ADJUSTING INPUT SENSITIVITY To reach a maximum noise-free dynamic headroom from each individual head unit/amplifier/speaker combination, it is important to set the respective input gain controls correctly. The input level settings determine the actual signal-to-noise ratio, and they are also responsible for obtaining the maximum distortion-free SPL (sound pressure level) from your specific setup.
6. TECHNICAL SPECIFICATIONS RN-1600 RN-2160 RN-4110 RN-460-200 MOS-FET Amplifier 1-Channel (Mono) 2-Channel 4- Channel 5- Channel Rated power output (*THD/14.4 V) 195 Wrms x 1 @ 4 Ω (<0.1 %*) 205 W x 1 @ 4 Ω (<1.0 %*) 300 Wrms x 1 @ 2 Ω (<0.1 %*) 350 W x 1 @ 2 Ω (<1.0 %*) 500 W x 1 @ 1 Ω (<1.0 %*) 145 Wrms x 2 @ 4 Ω (<0.1 %*) 155 W x 2 @ 4 Ω (<1.0 %*) 480 W x 1 @ 4 Ω (<1.0 %*) 240 W x 2 @ 2 Ω (<1.0 %*) 100 Wrms x 4 @ 4 Ω (<0.1 %*) 105 W x 4 @ 4 Ω (<1.0 %*) 300 W x 2 @ 4 Ω (<1.
7. WARRANTY Thank you for purchasing this RODEK amplifier. It is advisable to keep the original packing material for future transporting of the product. Please read the warranty specifications below carefully. Should your RODEK product require warranty service, please return it to the retailer from whom it was purchased, or the distributor in your country. Please do not send any product to RODEK Inc. U.S.A.
WARRANTY CERTIFICATE Model: RODEK POWER AMPLIFIER ❑ RN-1600 Serial number: ❑ RN-2160 ❑ RN-4110 RN-460-200 .......................................................................................................... Date of purchase: ................................................................................................... Your name: ❑ Dealer's address & stamp ....................................................................................................................