R&S®NGE100B Power Supply Series Reduced to the max Data Sheet | Version 01.
R&S®NGE100B Power Supply Series At a glance The R&S®NGE100B power supply series consists of robust, high-performance, affordable instruments. They offer high efficiency combined with low ripple plus a variety of comfort functions that are not usually found in this class of power supplies. The R&S®NGE100B power supply series consists of the R&S®NGE102B two-channel power supply and the R&S®NGE103B three-channel power supply. Both instruments provide up to 33.6 W output power per channel.
R&S®NGE100B Power Supply Series Benefits and key features Meets your daily needs ❙❙ All channels galvanically isolated and earth-free ❙❙ All channels electrically equivalent with the same voltage, current and power ❙❙ Parallel and serial operation ❙❙ Short-circuit-proof outputs ❙❙ Protection functions to safeguard instrument and DUT ❙❙ Modern architecture; small, compact and quiet ❙❙ Tailored to be used in education, labs and system racks ▷▷ page 4 Easy operation ❙❙ Straightforward operation ❙❙ Color-codin
Meets your daily needs All channels galvanically isolated and earth-free The R&S®NGE102B and R&S®NGE103B power supplies offer the choice between two or three channels. The circuitry of each single channel is completely separated from the others, there is no connection to chassis ground. This makes it easy to combine the channels to drive bipolar circuitries that might need +12 V/–12 V, for example, and avoids any ground problems in complex DUTs.
Easy operation Straightforward operation All basic R&S®NGE100B power supply functions can be operated via direct keys on the front panel – no need to maneuver through a jungle of menus. Just press the "Voltage" key, select an output channel and use the rotary knob or the arrow keys to adjust the desired voltage in steps down to 10 mV. A constant output current can be similarly set in steps down to 1 mA. Color-coding of operating conditions All operating conditions are shown clearly on the 3.
Connectivity – everything you need Front connectors with 4 mm safety binding posts The output connectors on the front of the R&S®NGE100B power supplies can hold 4 mm safety banana plugs or they can clamp stripped cables as very often seen in educational applications. The design of the connectors is robust enough to survive generations of students. USB interface (virtual COM port and TMC class) Via the USB interface, the instrument can be controlled from external PCs.
Specifications Definitions General Product data applies under the following conditions: ❙❙ Three hours storage at ambient temperature followed by 30 minutes warm-up operation ❙❙ Specified environmental conditions met ❙❙ Recommended calibration interval adhered to ❙❙ All internal automatic adjustments performed, if applicable Y-axis Specifications with limits Represent warranted product performance by means of a range of values for the specified parameter.
All data is valid at +23 °C (–3 °C/+ 7 °C) after 30 minutes warm-up time. Electrical specifications Outputs All channel outputs are galvanically isolated and not connected to ground. Number of output channels R&S®NGE102B Total output power 2 R&S®NGE103B 3 R&S®NGE102B max. 66 W R&S®NGE103B max. 100 W Maximum output power per channel 33.
Remote control Command processing time ≤ 30 ms Programming settling time within 1 % of final value Positive voltage change no load full load (resistive) 10 ms + command processing time Negative voltage change no load 500 ms + command processing time full load (resistive) 10 ms + command processing time 10 ms + command processing time Protection functions Overvoltage protection configurable for each channel Overpower protection configurable for each channel Overcurrent protection (electronic
General data Mains fuses 115 V AC power source IEC 60127-2/5 T 5 A 250 V 230 V AC power source IEC 60127-2/5 T 2.5 A 250 V Electromagnetic compatibility EU, in line with EU RE Directive 2014/53/EU (notified body: CTC advanced GmbH) applied standards: EN 61326-1, EN 61326-2-1, DRAFT EN 301 489-1 V 2.2.0, DRAFT EN 301 489-17 V 3.2.0, EN 300 328 V 2.1.
Ordering information Designation Type Order No. Two-channel power supply R&S®NGE102B 5601.3800.02 Three-channel power supply R&S®NGE103B 5601.3800.03 Ethernet remote control R&S®NGE-K101 5601.2204.03 Wireless LAN remote control R&S®NGE-K102 5601.2210.03 Digital trigger I/O R&S®NGE-K103 5601.2227.03 R&S®HZC95 5800.2054.
❙ ❙ ❙ ❙ ❙ Worldwide Local and personalized Customized and flexible Uncompromising quality Long-term dependability www.rohde-schwarz.com Sustainable product design ❙❙ Environmental compatibility and eco-footprint ❙❙ Energy efficiency and low emissions ❙❙ Longevity and optimized total cost of ownership Certified Quality Management ISO 9001 Certified Environmental Management ISO 14001 Rohde & Schwarz training www.training.rohde-schwarz.
