User's Manual Part 1
Table Of Contents
- System Manual
- R&S®NV830x DTV Transmitters ATSC
- Volume 1
- Contents
- Safety Instructions
- Design and Characteristics
- Contents
- 1 Design and Function
- 2 Specifications
- Installation
- Contents
- 1 Equipment Supplied 1
- 2 Overview 3
- 3 Setting Up Transmitter 4
- 4 Ventilation System 9
- 5 AC Power Supply 14
- 6 Amplifiers 19
- 7 Connecting Antenna/Dummy Antenna to RF Connector 20
- 8 Connection Panel 23
- 1 Equipment Supplied
- 2 Overview
- 3 Setting Up Transmitter
- 4 Ventilation System
- 5 AC Power Supply
- 6 Amplifiers
- 7 Connecting Antenna/Dummy Antenna to RF Connector
- 8 Connection Panel
- Contents
- Commissioning
- Contents
- 1 General Information 1
- 2 Preparing for Transmitter Startup 3
- 2.1 Preparing for Local Operation 3
- 2.2 Checking and Setting System and Operating Parameters 3
- 2.3 R&S NetCCU800 3
- 2.4 Setting Transmitter Type 9
- 2.5 Entering Exciter Settings 11
- 2.6 Entering Output Stage Settings 19
- 2.7 Setting Transmitter Output Power 21
- 2.8 Calibrating Power Displays 22
- 3 Completion of Startup Procedure 26
- 4 Precorrection 31
- 1 General Information
- 2 Preparing for Transmitter Startup
- 2.1 Preparing for Local Operation
- 2.2 Checking and Setting System and Operating Parameters
- 2.3 R&S NetCCU800
- 2.4 Setting Transmitter Type
- 2.5 Entering Exciter Settings
- 2.6 Entering Output Stage Settings
- 2.7 Setting Transmitter Output Power
- 2.8 Calibrating Power Displays
- 3 Completion of Startup Procedure
- 4 Precorrection
- Contents
Chapter 4 Commissioning
2098.0188.72 - 4.01 - E-1
CONTENTS
1 General Information ......................................................................... 1
1.1 Preparations ....................................................................................................1
1.2 Requirements ..................................................................................................2
1.3 Operating R&S NetCCU800 ...........................................................................2
2 Preparing for Transmitter Startup .................................................. 3
2.1 Preparing for Local Operation .......................................................................3
2.2 Checking and Setting System and Operating Parameters .........................3
2.3 R&S NetCCU800 .............................................................................................3
2.3.1 Switching On R&S NetCCU800 ...................................................................3
2.3.2 Changing User Type ....................................................................................3
2.3.3 Entering Basic Settings ................................................................................4
2.3.4 Setting Date and Time ..................................................................................5
2.3.5 Adjusting Network Settings ..........................................................................6
2.3.5.1 Front Ethernet Interface ..................................................................................... 6
2.3.5.2 Rear Ethernet Interface (NETLINK) ................................................................... 7
2.4 Setting Transmitter Type ...............................................................................9
2.5 Entering Exciter Settings .............................................................................11
2.5.1 Setting TV Standard ...................................................................................11
2.5.2 Configuring Input Interfaces .......................................................................12
2.5.2.1 Specifying Data Format for Data Streams Input 1 and Input 2 ......................... 12
2.5.2.2 Setting Automatic Input Switchover .................................................................. 13
2.5.3 Switching Off Precorrector .........................................................................14
2.5.4 Setting Transmitter Frequency ...................................................................15
2.5.5 Adjusting the I/Q Modulator ........................................................................16
2.5.6 Setting RF Output .......................................................................................17
2.5.7 Specifying Behavior on Failure of a Reference Source ..............................18
2.6 Entering Output Stage Settings ..................................................................19
2.6.1 Setting Up Output Stage ............................................................................19
2.7 Setting Transmitter Output Power ..............................................................21
2.8 Calibrating Power Displays .........................................................................22
2.8.1 Calibrating Forward and Reflected Power Displays ...................................22
3 Completion of Startup Procedure ................................................ 26