user manual

ManualsBrandsRola ManualsBicycle AccessoriesBicycle Accessories 59403

Product Code:

Product Name:

www.rolaproducts.com

Cequent Towing Products - Plymouth, MI

Technical Service: (888) 521-0510

59403N Rev B 9-29-06

59403

3 Place Bike Carrier - Folding

ASSEMBLY INSTRUCTIONS:

The shank for your (3) place bike carrier is pre-assembled to be used with a 2” hitch.

For use with a 2” hitch:

1. Tighten both hex bolts to 75 ft-lb to secure the shank to the Collar Bracket. (See Diagram 1)

For use with a 1-1/4” hitch:

1. Remove the two hex bolts holding shank to collar bracket.

2. Remove the two spacer plates. The spacer plates are not required for the 1-1/4” hitch application.

3. Insert the 2” square end of shank into collar bracket. Line up the two ½” diameter holes in shank with the two holes

in collar bracket. Re-Install the two ½” bolts and tighten bolts to 75 ft-lb.

(See Diagram 2)

Handle Mechanism

Release

Collar

Bracket

“Slotted”

Hole

½” x 3-1/4” Hex Bolt

(2) Nylon Flat Washer

Locknut

Main Support

Tube

Diagram 3

Diagram 1

½” x 3” Hex Bolt

Locknut

(2) Places

Tighten Bolts

Collar Bracket

Lock

Drop of Oil

2” Shank

Please read all instructions carefully before assembly, installation and/or use of this product.

Diagram 2

1. Use key to unlock lock on Collar Bracket.

2. Pull spring loaded release pin on side of Main Support tube,

remove handle mechanism, and rotate bike Support Arms

into the UP position. Re-insert the handle mechanism. Pull

out the spring loaded release pin and push handle all the

way down. Let the spring loaded pin go so that it fully

engages the handle mechanism.

3. Attach Main Support tube to Collar Bracket in orientation

shown (see Diagram 3). Line up the hole near end of main

support tube with the slotted hole in collar bracket and install

one (1) ½” x 3-1/4” lg. hex bolt, two (2) nylon flat washers,

and locknut as shown. Tighten locknut until it is snug

against the flat washers.

4. Lock Collar Bracket to Main Support tube so bike carrier is

in the upright position.

To attach Main Support tube to collar bracket:

1-1/4” Shank

½” Holes

½” x 3” Hex Bolt

Locknut

(2) Places

Tighten Bolts

5/8” Hole

Hitch pin

hole

Do not use first hole to secure bike

Rack to hitch.

Summary of content (9 pages)

PAGE 1
Product Name: 3 Place Bike Carrier - Folding Product Code: 59403 Please read all instructions carefully before assembly, installation and/or use of this product. ASSEMBLY INSTRUCTIONS: The shank for your (3) place bike carrier is pre-assembled to be used with a 2” hitch. For use with a 2” hitch: 1. Tighten both hex bolts to 75 ft-lb to secure the shank to the Collar Bracket. (See Diagram 1) For use with a 1-1/4” hitch: 1. Remove the two hex bolts holding shank to collar bracket. 2.
PAGE 2
Product Name: 3 Place Bike Carrier - Folding Product Code: 59403 Please read all instructions carefully before assembly, installation and/or use of this product. LOADING INSTRUCTIONS: 1. Place the bike rack receiver into your receiver hitch. Fit rack as close to vehicle as possible. 2. For 2” hitch, secure rack with 5/8” hitch pin and clip. For 1-1/4” hitch, secure rack with ½” pin and clip (See Diagram 2 & 4) Note: Must use the second or third hole 1-1/4” shank to secure bike rack to hitch. 1.
PAGE 3
Product Name: 3 Place Bike Carrier - Folding Product Code: 59403 Please read all instructions carefully before assembly, installation and/or use of this product. IMPORTANT NOTES: • This bicycle rack has been designed to carry three (3) bikes, as long as the maximum weight on the rack does not exceed 45 kgs or 100 lb. • This rack is designed for typical use and applications (on paved or smooth gravel roads).
PAGE 4
Product Name: Porte-vélos à 3 places - Pliable Product Code: 59403 Il importe de lire attentivement toutes les instructions avant l’assemblage, l’installation et/ou l’utilisation de ce produit. INSTRUCTIONS DE MONTAGE : La barre d’accouplement de votre porte-vélos à 3 places est pré-assemblée en fonction d’un attelage de 2 po. Pour utilisation avec un attelage de 2 po : 1. Serrer les deux boulons au couple de 75 lb-pi pour fixer la barre d’accouplement au collet.
PAGE 5
Product Name: Porte-vélos à 3 places - Pliable Product Code: 59403 Il importe de lire attentivement toutes les instructions avant l’assemblage, l’installation et/ou l’utilisation de ce produit. INSTRUCTIONS DE CHARGEMENT : 1. Placer le récepteur du support à vélos dans le récepteur de l’attelage. Positionner le support aussi près du véhicule que possible. 2. Dans le cas d’un attelage de 2 po, fixer le support à l’aide de la cheville et agrafe d’attelage de 5/8 po.
PAGE 6
Product Name: Porte-vélos à 3 places - Pliable Product Code: 59403 Il importe de lire attentivement toutes les instructions avant l’assemblage, l’installation et/ou l’utilisation de ce produit. REMARQUES IMPORTANTES : • Ce support à vélos a été conçu pour transporter trois (3) vélos, en autant que le poids maximum sur le support ne dépasse pas 45 kg (100 lb). • Ce support convient à un usage et des applications normaux (route pavée ou en gravier fin).
PAGE 7
Product Name: Cargador para 3 bicicletas - Plegable Product Code: 59403 Lea todas las instrucciones atentamente antes de armar, instalar y/o usar este producto. INSTRUCCIONES PARA ARMAR: La espiga para el cargador de 3 bicicletas viene pre-armada para usarse con un enganche de 2”. Para uso con un enganche de 2”: 1. Apriete ambos pernos hexagonales hasta 75 pies-lb. para asegurar la espiga al soporte del collar. (Ver diagrama 1) Para uso con un enganche de 1-1/4”: 2.
PAGE 8
Product Name: Cargador para 3 bicicletas - Plegable Product Code: 59403 Lea todas las instrucciones atentamente antes de armar, instalar y/o usar este producto. INSTRUCCIONES DE CARGA: 1. Coloque el receptor del portabicicletas en el enganche receptor. Ajuste el portabicicletas lo más cercano al vehículo como sea posible. 2. Para enganches de 2”, asegure el portabicicletas con un pasador y gancho de 5/8” para enganche.
PAGE 9
Product Name: Cargador para 3 bicicletas - plegable Product Code: 59403 Lea todas las instrucciones atentamente antes de armar, instalar y/o usar este producto. NOTAS IMPORTANTES: • Esta bandeja está diseñada para cargar tres bicicletas, siempre que el peso máximo en la bandeja no supere 45 kgs ó 100 lb. • Esta bandeja está diseñada para uso y aplicaciones normales (sobre carreteras pavimentadas o de gravilla uniforme).