User Manual

ManualsBrandsRoland ManualsControl UnitsTD3 Sound module - SOUND MODULE

Table Of Contents

USING THE UNIT SAFELY
IMPORTANT NOTES
Contents
Features
Panel Descriptions
- Top Panel
- Rear Panel
- Side Panel
Setting Up the Kit
- Mounting the TD-3 on the Stand
- Connecting the Pads and the Pedals
- Connecting Headphones, Audio Equipment, Amps, and Other Gear
- Turning On/Off the Power
  - Turning Off the Power
Choosing a Drum Kit
- Hearing What the Kits Sound Like (Preview)
Playing the Drum Kit
- Trigger Inputs and Triggering Possibilities
- Playing the Pads
- Hi-Hat Control Pedal
Creating Your Own Drum Kit
- Choosing a Drum Kit [DRUM KIT]
- Selecting Sounds [INST]
- Instrument Volume & Pan [LEVEL/PAN]
- Ambience Settings [AMBIENCE]
  - Switching Ambience On/Off
  - Selecting the Ambience Type
- Copying a Drum Kit [KIT COPY]
Playing with the Metronome (Click)
- Starting and Stopping the Metronome On/Off [CLICK]
- Tempo Adjustment [TEMPO]
- Setting the Time Signature [BEAT]
- Selecting a Rhythm Type [RHYTHM TYPE]
- Selecting the Click Sound [CLICK INST]
- Volume Adjustment [CLICK LEVEL]
Playing with a CD, Tape, or MD (Via MIX IN Jack)
COACH Mode
- Setting Procedure
- Accuracy and Timing Exercises
- Endurance and Stamina Exercises
  - Gradual Up/Down—Tempo Increase/Decrease Exercise
  - Step Up/Down—Tempo Increase/Decrease in Steps
- Voice “Count In” / Visual Measure Counter
  - Count In and Measure Counter
Pad Adjustments
- Adjusting Pad Sensitivity [PAD SENS]
- Eliminate Crosstalk Between Pads [XTALK CANCEL]
Hi-Hat Control Pedal Adjustment
- Adjusting the Hi-Hat’s Foot Closed Level
Factory Reset (Restoring the Factory Settings)
About the Pads
- Trigger Inputs and the Pads You Can Use
- Playing the Pads
Pad Configuration Possibilities
- Three Toms and Three Cymbals
- Two Toms and Four Cymbals
Pad and Trigger Settings
- Selecting the Pad Type (Trigger Type)
- Adjusting Pad Sensitivity
- Setting the Minimum Levels for the Pads (Threshold)
- How Playing Dynamics Changes the Volume (Velocity Curve)
- Adjusting the Trigger Signal Detection Time (Scan Time)
- Detecting Trigger Signal Attenuation and Cancelling Incorrect Triggering (Retrigger Cancel)
- Eliminate Crosstalk Between Pads (Crosstalk Cancel)
- Double Triggering Prevention (Mask Time)
- Rim Shots Response (Rim Sensitivity)
- Rim/Edge Dynamic Response (Rim Gain)
MIDI Settings
- About MIDI
  - MIDI Connectors
- MIDI Note Number for Each Pad [NOTE#]
- When Only Using as a MIDI Controller (Local Control)
- Saving Data to an External MIDI Device (Bulk Dump)
  - Loading Data to the TD-3
- Using MIDI
Troubleshooting / Error Messages
- Troubleshooting
- Error Messages
Drum Kit List
Drum Instrument List
MIDI Implementation Chart
Specifications
Index

COACH Mode

The TD-3’s Coach mode is a unique set of exercises specifically designed to help build speed, accuracy

and stamina, as well as develop better timing skills. Throughout the Coach modes, you will discover that

some of them have programmable parameters, allowing you to adapt the functions to your specific needs.

fig.coach00

Press [COACH].

Press [COACH] a few times to select the parameter.

You can hold down [COACH] and press [-] to select parameters in the reverse order of that

when only [COACH] is pressed.

Press [+] or [-] to select the variation.

Press [CLICK] to begin the exercise.

To finish the exercise, press [CLICK] again.

Selecting the Coach mode while the Metronome is working stops the metronome.

In Coach mode, you can press [TEMPO] to change the tempo before pressing [CLICK] to

start the exercise. Adjust the tempo using [+] or [-].

Setting Procedure

Display

Parameter Practice Content Page

Rhythmic Notes

Accuracy and Timing Exercise (4 types) p. 36

Time Check

Quiet Count

Speed Check

Gradual Up/Down Endurance and Stamina Exercise (2 types) p. 38

Step Up/Down

Count In Adding Finishing Touches to What You Have Practiced p. 39

1, 2 3

4, 5

TD-3_e.book 35 ページ２００５年５月２０日　金曜日　午後４時５７分