User Manual

ManualsBrandsRoland ManualsControl UnitsTD3 Sound module - SOUND MODULE

Table Of Contents

USING THE UNIT SAFELY
IMPORTANT NOTES
Contents
Features
Panel Descriptions
- Top Panel
- Rear Panel
- Side Panel
Setting Up the Kit
- Mounting the TD-3 on the Stand
- Connecting the Pads and the Pedals
- Connecting Headphones, Audio Equipment, Amps, and Other Gear
- Turning On/Off the Power
  - Turning Off the Power
Choosing a Drum Kit
- Hearing What the Kits Sound Like (Preview)
Playing the Drum Kit
- Trigger Inputs and Triggering Possibilities
- Playing the Pads
- Hi-Hat Control Pedal
Creating Your Own Drum Kit
- Choosing a Drum Kit [DRUM KIT]
- Selecting Sounds [INST]
- Instrument Volume & Pan [LEVEL/PAN]
- Ambience Settings [AMBIENCE]
  - Switching Ambience On/Off
  - Selecting the Ambience Type
- Copying a Drum Kit [KIT COPY]
Playing with the Metronome (Click)
- Starting and Stopping the Metronome On/Off [CLICK]
- Tempo Adjustment [TEMPO]
- Setting the Time Signature [BEAT]
- Selecting a Rhythm Type [RHYTHM TYPE]
- Selecting the Click Sound [CLICK INST]
- Volume Adjustment [CLICK LEVEL]
Playing with a CD, Tape, or MD (Via MIX IN Jack)
COACH Mode
- Setting Procedure
- Accuracy and Timing Exercises
- Endurance and Stamina Exercises
  - Gradual Up/Down—Tempo Increase/Decrease Exercise
  - Step Up/Down—Tempo Increase/Decrease in Steps
- Voice “Count In” / Visual Measure Counter
  - Count In and Measure Counter
Pad Adjustments
- Adjusting Pad Sensitivity [PAD SENS]
- Eliminate Crosstalk Between Pads [XTALK CANCEL]
Hi-Hat Control Pedal Adjustment
- Adjusting the Hi-Hat’s Foot Closed Level
Factory Reset (Restoring the Factory Settings)
About the Pads
- Trigger Inputs and the Pads You Can Use
- Playing the Pads
Pad Configuration Possibilities
- Three Toms and Three Cymbals
- Two Toms and Four Cymbals
Pad and Trigger Settings
- Selecting the Pad Type (Trigger Type)
- Adjusting Pad Sensitivity
- Setting the Minimum Levels for the Pads (Threshold)
- How Playing Dynamics Changes the Volume (Velocity Curve)
- Adjusting the Trigger Signal Detection Time (Scan Time)
- Detecting Trigger Signal Attenuation and Cancelling Incorrect Triggering (Retrigger Cancel)
- Eliminate Crosstalk Between Pads (Crosstalk Cancel)
- Double Triggering Prevention (Mask Time)
- Rim Shots Response (Rim Sensitivity)
- Rim/Edge Dynamic Response (Rim Gain)
MIDI Settings
- About MIDI
  - MIDI Connectors
- MIDI Note Number for Each Pad [NOTE#]
- When Only Using as a MIDI Controller (Local Control)
- Saving Data to an External MIDI Device (Bulk Dump)
  - Loading Data to the TD-3
- Using MIDI
Troubleshooting / Error Messages
- Troubleshooting
- Error Messages
Drum Kit List
Drum Instrument List
MIDI Implementation Chart
Specifications
Index

Troubleshooting / Error Messages

Error Messages

Display Meaning Action

Data in the TD-3’s memory may be

corrupted.

“ ” appears when [DRUM KIT] is pressed. Hold

down [DRUM KIT] once more. Only the settings for the

corrupted portion are subject to Factory Reset (doing so

will erase any changes you have made). If this does not re-

solve the problem, consult your Roland dealer or nearest

Roland Service Center.

A problem has occurred with the inter-

nal system.

Consult your Roland dealer or nearest Roland Service

Center.

(Scroll Display)

A large amount of MIDI messages

were received, and could not be pro-

cessed completely.

Double check your MIDI connections (p. 62, p. 64). If this

does not solve the problem, reduce the amount of MIDI

messages being transmitted to the TD-3.

(Scroll Display)

Something has caused a break in com-

munication with the external MIDI de-

vice.

Verify your MIDI connections.

(Scroll Display)

The checksum value of a system exclu-

sive message was incorrect.

Correct the checksum value.

(Scroll Display)

The TD-3 failed to receive a MIDI mes-

sage correctly.

Transmit the MIDI message to the TD-3 once again.

TD-3_e.book 67 ページ２００５年５月２０日　金曜日　午後４時５７分