User Manual
Table Of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- Introduction
- Contents
- USING THE UNIT SAFELY
- Important Notes
- Names of Things and What They Do
- Before You Play
- Listening to Demo Songs
- Performing
- Performing with a Variety of Sounds
- Adjusting the Piano Sound to Your Taste (Piano Designer)
- Adjusting the Keyboard Sensitivity (Key Touch)
- Adding Spatial Depth to the Sound (3D Sound Control)
- Adding Liveliness to the Sound (Dynamics Sound Control)
- Adding Reverberation to Sounds (Reverb Effect)
- Adding a Variety Effects to the Sound (Effects)
- Changing the Key of the Keyboard (Key Transpose)
- Dividing the Keyboard for Two-person Performance (Twin Piano)
- Performing with Two Layered Tones (Dual Play)
- Performing with Different Tones in the Left and Right Sides of the Keyboard (Split Play)
- Performing with the Metronome
- Sounding a Count to Keep Your Timing Accurate
- Playing Back Songs
- Recording
- Saving Your Performance
- Various Settings
- Basic Operation in Function Mode
- Tuning Settings
- Equalizer Settings
- Song Playback Settings
- Changing the CD Settings
- Metronome Setting
- Keyboard Settings
- Pedal Settings
- MIDI Settings
- Other Settings
- Using the V-LINK Function (V-LINK)
- Specifying the V-LINK Transmission Channel
- Changing the USB Driver Settings (USB Driver)
- Changing the External Memory Setting (Ext. Memory Mode)
- Adjusting the Volume (Master Gain)
- Changing How Grand Space is Applied (3D Mode)
- Changing the Parts Assigned to the Track Buttons During SMF Playback (Track Assign)
- Switching On/Off the Display of Lyrics (Lyrics)
- Switching VIMA TUNES Recommended Tones (Recommended Tone)
- Changing the Language Displayed in the Screen (Language)
- Remembering the Settings (Memory Backup)
- Restoring the Settings to the Factory Condition (Factory Reset)
- Disabling the Buttons (Panel Lock)
- Connecting to Other Devices
- Troubleshooting
- Error Messages
- Tone List
- Internal Song List
- Parameters Stored in Memory Backup
- Music Files That the LX-10 Can Use
- MIDI Implementation Chart
- Main Specifications
- Index
23
Before You Play
You can use headphones to enjoy the LX-10 without disturbing
those around you, such as at night. Since the LX-10 has two
headphone jacks, two people can also use headphones
simultaneously.
If you’re using only one set of headphones, you may connect
them to either of the two headphone jacks.
fig.Headphones.eps
1.
Plug the headphones into the Phones jack
located at the left of front side bottom of the
LX-10’s bottom panel.
If headphones are connected, no sound will be output
from the LX-10’s speakers.
2.
Use the LX-10’s [Volume] knob (p. 21) to
adjust the headphone volume.
Cautions when Using Headphones
• To prevent damage to the cord’s internal conductors, avoid
rough handling. When using headphones, mainly try to
handle either the plug or the headset.
• Your headphones may be damaged if the volume of a device
is already turned up when you plug them in. Minimize the
volume before you plug in the headphones.
• Excessive input will not only damage your hearing, but may
also strain the headphones. Please enjoy music at an
appropriate volume.
• Use headphones that have a stereo 1/4” phone plug.
Whenever you are not using the headphones, you can hang
them on the headphone hook of the LX-10.
Attaching the Headphone Hook
1.
Press and twist the headphone hook
included with the LX-10 into the hole in the
bottom left of the LX-10 (refer to the figure
above).
2.
Turn the headphone hook wing nut to secure
the headphone hook.
Do not hang anything other than headphones on the
headphone hook. Doing so may damage the
instrument or the hook.
If headphones are connected, a headphone symbol is
shown in the lower left of the screen.
fig.PhonesMark.eps
Listening through
Headphones
Headphones
Using the Headphone Hook
Headphone Hook
Wing Nut
NOTE
LX-10_e.book 23 ページ 2009年2月13日 金曜日 午前10時39分