Owner`s manual

ManualsBrandsRoland ManualsComputer equipmentAE-7000

VM-C7200/C7100 Newly Added Functions

Table of Contents

Newly Added Functions (Ver.1.1).................................1

How to connect the ADA-7000

and the AE-7000 series..................................................1

If the system software of the VMC7200/C7100 is

Ver.1.10 or later.................................................................................2

How to connect the AE-7000

and the VM-7000 series.................................................3

If the system software of the VM-C7200/C7100 is

Ver.1.10 or later.................................................................................4

How to connect the VSR-880

and the VM-7000 series.................................................4

MTR control functions.....................................................................5

Newly Added Functions (Ver.1.5).................................6

Dynamics Processing on Every Input Channel.........6

Selecting the dynamics processor...................................................6

Editing Dynamics Processor...........................................................7

Using Libraries..................................................................................8

Scene...................................................................................................8

Automix .............................................................................................8

Others..............................................................................9

Effects Bypass Switch.......................................................................9

INPLACE SOLO ...............................................................................9

SOLO SW Flashing...........................................................................9

Monitor Source Select.......................................................................9

Libraries Newly Added..............................................10

PROJECTs, SCENEs and TEMPLATEs

created on the VM-7000 Ver.1.1 or 1.5........................10

MEMO..............................................................................11

Newly Added Functions (Ver.1.1)

Following functions have been added to the system for the

VM-C7200/C7100 (V-Mixing Console; Ver.1.1 or later).

When you turn on the power of the VM-C7200/7100, current

system version number of your VM-C7200/C7100 will be

appeared in the display.

How to connect the ADA-7000

and the AE-7000 series

To connect the VM-7200/7100 and the ADA-7000 via R-BUS,

VM-24E I/O Expansion Board (sold separately) is needed.

By installing the VM-24E to the VM-7200/7100 processor,

you can connect up to three ADA-7000’s.

* Refer to VM-7200/7100 Owner’s Manual p. 14 “Installing R-

BUS (RMDB2) Connectors (VM-24E).”

Connection

Connect the VM-7200/7100 and the ADA-7000 with the R-

BUS cable attached in the ADA-7000 box.

* Refer to ADA-7000 Owner’s Manual p. 9 “An Example of

Connection.”

Booting up

Turn the power on the ADA-7000 first, then the VM-7200/

7100 processor, and finally the VM-C7200/C7100 console.

Clock source setting

If clock source has not been set, noise may be generated from

the audio output on the ADA-7000 and the VM-7000. While

setting the clock source, please turn down the master and

monitor level, and turn up again after the setting is finished.

Set the sampling clock on the ADA-7000 and the VM-7000 as

follows.

Clock Source on the ADA-7000

connected to the R-BUS (1–8):...................................R-BUS

Clock Source on the ADA-7000

connected to the R-BUS (9–16):.................................R-BUS

Clock Source on the ADA-7000

connected to the R-BUS (17–24):...............................R-BUS

Master clock on the VM-7000: ................................INTERNAL

Summary of content (12 pages)

PAGE 1
VM-C7200/C7100 Newly Added Functions Table of Contents Newly Added Functions (Ver.1.1) Newly Added Functions (Ver.1.1).................................1 Following functions have been added to the system for the VM-C7200/C7100 (V-Mixing Console; Ver.1.1 or later). When you turn on the power of the VM-C7200/7100, current system version number of your VM-C7200/C7100 will be appeared in the display. How to connect the ADA-7000 and the AE-7000 series ..................................................
PAGE 2
VM-C7200/C7100 Newly Added Functions ADA-7000 setting fig.ada_70 Check if the clock source on the ADA-7000 is set to R-BUS. When the ADA-7000 is booted up, the clock source is set to R-BUS. If you connect multiple ADA-7000, set the clock source on all ADA-7000 to R-BUS. * Refer to ADA-7000 Owner’s Manual p. 6 “Clock source.” VM-7000 setting Set the master clock of the VM-7200/7100 to INTERNAL as follows. 1. Hold down [SHIFT], and press [SYSTEM] (PROJECT). 2.
PAGE 3
VM-C7200/C7100 Newly Added Functions 3. Control the gain and phantom power on/off in the same manner as for the [INPUT]. * PAD on the ADA-7000 is automatically switched on/off according to the gain setting. How to connect the AE-7000 and the VM-7000 series To connect the VM-7200/7100 and the AE-7000 via R-BUS, VM-24E I/O Expansion Board (sold separately) is needed. By installing the VM-24E to the VM-7200/7100 processor, you can connect up to three AE-7000’s. * Refer to VM-7200/7100 Owner’s Manual p.
PAGE 4
VM-C7200/C7100 Newly Added Functions Example 3 • If AES/EBU device does not output the word clock Connect the output of the AES/EBU device to the INPUT A of the 1st AE-7000. In this case, please set the clock source on the AE-7000, and then the master clock on the VM-7000. Clock source on the 1st AE-7000: ............................... INPUT A Clock source on the 2nd and later AE-7000’s:................R-BUS Master clock on the VM-7000: ...........................
PAGE 5
VM-C7200/C7100 Newly Added Functions VSR-880 Settings 3. Set up the following in the SETUP page. Set the some parameters of the VSR-880 as follows.
PAGE 6
VM-C7200/C7100 Newly Added Functions * Latest song list can be displayed by pressing [F6] (SCAN). Song Store You can store the current song to the VSR-880 hard disk. 1. Hold down [SHIFT], and press [SYSTEM (PROJECT). The SYSTEM menu appears in the display. 2. Select “SYSTEM CONFIG” and then “R-BUS (1/2/3)” page. 3. Press [F3] (STORE) and Song Store is executed. Shutdown You can shut down the VSR-880. Newly Added Functions (Ver.1.
PAGE 7
VM-C7200/C7100 Newly Added Functions fig.03_70 6. Press [F1] (SET) to make the algorithm effective on the channel. Dialog is closed and the edit page of the selected algorithm appears. Editing Dynamics Processor By the dynamics algorithm you selected, contents of the edit page in “DELAY/DY” vary. Compressor Compresses the total output signal when the input level surpasses the threshold. fig.04_70 4. Highlight the desired algorithm with V1 knob (SELECT). 5.
PAGE 8
VM-C7200/C7100 Newly Added Functions Expander fig.06_70 Expanding the dynamic range with a certain ratio. fig.05_70 Scene [ON] On/Off switch of the expander Thresh Threshold level at which the expander starts working. Ratio Expanding ratio to the input signal level Attack Time how quickly the expander starts working when the input signal exceeds the threshold level. Release Time how long the expander works after the input signal has fallen below the threshold level.
PAGE 9
VM-C7200/C7100 Newly Added Functions 3. Press [AUTO-MIX] under CH STATUS. INPLACE SOLO 4. Press the status buttons for the channel for which automixing is to be recorded to set it to the recording state (indicator: red). Function is modified when SOLO MODE (Owner’s Manual p.107) is set to INPLACE as follows. When soloing INPUT or MULTI IN, the effect inserted to FLEX BUS can be monitored simultaneously. If SOLO mode is not “INPLACE,” function is the same as the previous version. 5.
PAGE 10
VM-C7200/C7100 Newly Added Functions Libraries Newly Added Following channel dynamics libraries have been added to the system for the VM-C7200/C7100 (Ver.1.1 or later). Channel Dynamics Libraries (20 presets) No.
PAGE 11
VM-C7200/C7100 Newly Added Functions MEMO 11
PAGE 12
VM-C7200/C7100 Newly Added Functions MEMO Copyright © 2000 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland International Website http://www.roland.co.