* 5 1 5100001499 0 0 0 0 1 4 9 9 - 0 1 * 08-08-1N
AT-75_e.book 1 ページ ２００８年８月２１日 201b 木曜日 午前１０時９分 Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY” (p. 3), and “IMPORTANT NOTES” (p. 6). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety.
AT-75_e.book 2 ページ ２００８年８月２１日 木曜日 午前１０時９分 WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
AT-75_e.book 3 ページ ２００８年８月２１日 木曜日 午前１０時９分 USING THE UNIT SAFELY The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
AT-75_e.book 4 ページ ２００８年８月２１日 木曜日 午前１０時９分 USING THE UNIT SAFELY Turn off the power if an abnormality or malfunction occurs Place in a well ventilated location 101a When using this device, ensure that it is placed in a well ventilated location. 012a If any of the following should occur, immediately turn off the power, disconnect the power cord from the AC outlet, and contact your dealer or a service center to have the device serviced.
AT-75_e.book 5 ページ ２００８年８月２１日 木曜日 午前１０時９分 USING THE UNIT SAFELY Unplug the power cord from the AC outlet before cleaning 109a Before you clean the device, turn off the power and unplug the power cord from the AC outlet. ..........................................................................................................
AT-75_e.book 6 ページ ２００８年８月２１日 木曜日 午前１０時９分 IMPORTANT NOTES Power Supply Care 301 401b • Do not connect this device to the same electrical outlet as an inverter-controlled device such as a refrigerator, microwave oven, or air conditioner, or a device that contains an electric motor. Depending on how the other device is used, power supply noise could cause this device to malfunction or produce noise.
AT-75_e.book 7 ページ ２００８年８月２１日 木曜日 午前１０時９分 IMPORTANT NOTES Floppy Disk Handling (Using Optional Floppy Disk Drive) 651 • Floppy disks contain a plastic disk with a thin coating of magnetic storage medium. Microscopic precision is required to enable storage of large amounts of data on such a small surface area. To preserve their integrity, please observe the following when handling floppy disks: • Never touch the magnetic medium inside the disk. • Do not use or store floppy disks in dirty or dusty areas.
AT-75_e.book 8 ページ ２００８年８月２１日 木曜日 午前１０時９分 Main Features We want to take a moment to thank you for your purchase of the Roland Organ “Music ATELIER AT-75.” The ATELIER is an electronic organ which provides a generous collection of rich organ sounds. In addition, it is designed to be easy to learn and use. In order to enjoy reliable performance of your new keyboard for many years to come, please take the time to read through this manual in its entirety.
AT-75_e.book 9 ページ ２００８年８月２１日 木曜日 午前１０時９分 Main Features Highly realistic Rhythms and Automatic Accompaniment functions All Rhythms use data from performances by professional drummers, featuring high-quality patterns with all the grooves and subtle nuance of the real thing. In addition, you can use Automatic Accompaniments that are perfectly matched to each Rhythm to enjoy the feeling of playing with your own band in the background.
AT-75_e.book 10 ページ ２００８年８月２１日 木曜日 午前１０時９分 Contents USING THE UNIT SAFELY........................................................................ 3 IMPORTANT NOTES ............................................................................... 6 Main Features........................................................................................ 8 Conventions Used in This Manual ............................................................................... 9 Contents ...................................
AT-75_e.book 11 ページ ２００８年８月２１日 木曜日 午前１０時９分 Contents Using the Rhythm Performance............................................................. 41 Selecting a Rhythm........................................................................................................... 41 Using Rhythms Stored in User Memory ...................................................................... 42 Playing Rhythm..............................................................................................................
AT-75_e.book 12 ページ ２００８年８月２１日 木曜日 午前１０時９分 Contents Record and Playback Your Performance ............................................... 82 What is a Track Button? .......................................................................................... 82 Playing Back Performance Songs Stored on USB Memory and SMF Music Files....................... 83 Silencing a Specific Track (Track Mute) .............................................................................. 84 Recording a Performance.......
AT-75_e.book 13 ページ ２００８年８月２１日 木曜日 午前１０時９分 Contents Adjusting the Timing of a Player Piano CD’s Piano Sound and Accompaniment (CD/Audio Sync).................................................................................................. 108 Other Settings ............................................................................................................... 109 Adjust the Standard Pitch (Master Tune)...................................................................
AT-75_e.book 14 ページ ２００８年８月２１日 木曜日 午前１０時９分 Panel Descriptions 3 10 4 11 19 5 8 12 20 6 13 14 7 9 16 15 1718 21 1. [Power On] switch ( → p. 16) 8. [One Touch Program] button ( → p. 51) 2. 3. [Master Volume] knob ( → p. 17) Harmonic Bars ( → p. 28) 9. [Harmony Intelligence] button( → p. 73) 4. Pedal Bass Voice Select buttons ( → p. 25) 11. Vintage Organ buttons ( → p. 28) Pedal Part [To Lower] button ( → p. 36, p. 40) Level [▲] [▼] buttons ( → p. 34) 5.
AT-75_e.book 15 ページ ２００８年８月２１日 木曜日 午前１０時９分 Panel Descriptions Panel Descriptions 1 2 Write Manual 1 2 3 4 22 16. [Load] button ( → p. 63, p. 87, p. 92) 17. [Save] button ( → p. 61, p. 89) 18. Beat Indicator ( → p. 46) 19. Composer ( → p. 82) [Song] button [Registration] button [Media] button [Bass] button [Lower] button [Solo/Upper] button [Reset] button [Play/Stop] button [Rec] button [Bwd] button [Fwd] button 20. Rhythm Select buttons ( → p. 41) Tempo [ ][ ] buttons ( → p.
AT-75_e.book 16 ページ ２００８年８月２１日 木曜日 午前１０時９分 Before You Start Playing Setting Up the Music Rest Turning the Power On and Off 941 fig.01-03 NOTE Once the connections have been completed, turn on or off power to your various devices in the order specified. By turning on or off devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. Turning On the Power 1. 1. Attach the music rest by inserting it into the two holes. Connecting the Power Cord 1.
AT-75_e.book 17 ページ ２００８年８月２１日 木曜日 午前１０時９分 Before You Start Playing 3. Adjust the volume to an appropriate level by moving the [Master Volume] knob or operating the expression pedal. The ATELIER features Phones jacks. These allow you to play without having to worry about bothering others around you, even at night. fig.00-29.eps fig.00-28.eps decrease the volume increase the volume decrease the volume increase the volume 1.
AT-75_e.book 18 ページ ２００８年８月２１日 木曜日 午前１０時９分 Before You Start Playing I Using the Cord Hook NOTE Do not turn off the power while the following screen is displayed. fig.01-16 If you’re using headphones, you can use the cord hook to neatly bundle the cables near your feet. Attaching the Cord Hook 1. 2. When factory reset is completed, the basic screen appears. Screw the cord hook (with wing nut) about 80% of the way into the screw hole located at the bottom left of the ATELIER.
AT-75_e.book 19 ページ ２００８年８月２１日 木曜日 午前１０時９分 Before You Start Playing Using the External Memory 1. Grasp the External Memory connector holder and turn it 90 degrees to the left or right. You can also play back SMF music files saved on USB memory or a floppy disk (p. 83). NOTE External Memory Connector Holder Use USB memory and floppy disk drive available from Roland. Proper operation cannot be guaranteed if other USB device is used.
AT-75_e.book 20 ページ ２００８年８月２１日 木曜日 午前１０時９分 Before You Start Playing Using a CD You can connect a commercially available CD drive and play back audio CDs and CD-ROMs containing saved SMF music files. 3. Turn on the power to the ATELIER. 4. Turn on the power to the connected CD drive. For information on how to perform the following CD-drive operations, refer to the owner’s manual for the drive. NOTE You can also play songs on VIMA CD-ROMs (VIMA TUNES) sold by Roland.
AT-75_e.book 21 ページ ２００８年８月２１日 木曜日 午前１０時９分 About the Display The ATELIER has three types of basic screen: the Rhythm Screen, the Composer Screen and the Registration Screen. You can alternate from one to the other by pressing the [Display/Exit] button. fig.01-17 About the Display Basic Screens Rhythm Screen fig.01-18 Tempo Beat Measure Rhythm Name Chord Name Composer Screen When internal music data is selected: fig.01-19 Tempo Beat Measure Song Name Chord Name Registration Screen fig.
AT-75_e.book 22 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Listening to the Demo Songs The ATELIER contains 6 Demo songs. Here’s how to play the Demo songs, and fully appreciate the sounds, Rhythms, and Automatic Accompaniment that are available with the ATELIER. fig.02-01 2 NOTE Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws.
AT-75_e.book 23 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds If the following screen appears If the performance song in the ATELIER has not been saved to a USB memory or Favorites (User memory), the following message will appear, and it will not be possible to play the Demo songs. fig.02-03 If you wish to save the performance data, refer to “Saving Performance Songs” (p. 89) 23 Selecting and Playing Sounds If you don’t mind erasing this song, press the [Rec] button.
AT-75_e.book 24 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Selecting Voices The ATELIER is able to produce the sounds of various instruments. These sounds are called “Voices.” About the Voices and Parts The ATELIER has two keyboards and one Pedalboard, as shown below. From top to bottom these are called the “Upper Keyboard,” “Lower Keyboard,” and “Pedalboard.” fig.02-04 Upper Keyboard Lower Keyboard Pedalboard The Upper Keyboard has three parts: “Upper,” “Solo“ and “Vintage Organ.
AT-75_e.book 25 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Functions of the Upper/Lower/Pedal Bass Sound Select Buttons fig.02-05 NOTE Each time you press a voice button, its indicator will switch between being lit and being turned off. Voices that have their button indicator lit can be played. Selecting the Upper/Lower/Pedal Bass Voices Select voices by pressing the Upper, Lower and Pedal Bass Voice Part buttons.
AT-75_e.book 26 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Selecting Solo Voice The Solo section of the Upper keyboard is monophonic, that is, the Solo voice will only sound for the highest note played on the Upper keyboard. fig.02-11 Example: Selecting “Tenor” for the Solo Voice Part 1. Press the Solo [Sax] button (indicator lights). The name of the selected voice appears in the display for a few seconds. fig.02-12 Play the Upper keyboard.
AT-75_e.book 27 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Selecting a Voice Using the [Others] Button Notice that there is an [Others] button for each part. By using the [Others] button, you can select all voices. 1. Press the [Others] button for the Part for which you wish to specify a voice. The voice name appears in the display. fig.02-10 (P.29) You can jump by voice group by pressing Menu [ ][ ] buttons to select the voice.
AT-75_e.book 28 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Creating Organ Sounds (Vintage Organ) The Vintage Organ buttons lets you add vintage organ sounds to the upper and lower parts. In addition, you can also use the harmonic bars to modify the selected sound as desired. The ATELIER provides nine harmonic bars for the upper part and lower part. Each harmonic bar is assigned a sound of a different footage (pitch), and by layering these sounds you can create a variety of organ tones.
AT-75_e.book 29 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds What’s the feet? “Feet” is a term that began as a measurement of the length of the pipes in a pipe organ. The pipes that produce the basic pitch (fundamental) for each note are considered to be “8 feet” in length.
AT-75_e.book 30 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Playing a Vintage Organ Voice Turning on the Vintage Organ 1. Press the Vintage Organ [On/Off] button so its indicator is lit. Each time you press the button, the indicator will alternate between ON (lit) and OFF. NOTE Glide and sustain effects are not applied to the Vintage Organ voice. The Vintage organ screen appears. fig.01-24.
AT-75_e.book 31 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Adding Sparkle to the Sound (Percussion) This adds an attack sound to the beginning of the note, making the sound crisper. 1. Press the Percussion [2 2/3'] button so its indicator is lit. Play the Upper keyboard and notice that an attack has been added. Explanation Percussion [2 2/3'] button Percussion one octave and a fifth above NOTE When the Percussion [2 2/3'] button is on, the 1' pitch will not be produced.
AT-75_e.book 32 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Adjusting the Volume of the Vintage Organ You can adjust the volume of the Vintage Organ sound to regulate the volume balance relative to the other sounds. 1. Press the [Utility] button. fig.05-08.eps 2. Press the Menu [ ] [ ] buttons a number of times to select “VintageOrganVolume.” fig.VoiceList.eps 3. Press the Value [-] [+] buttons to select the value for volume of the vintage organ. Setting 0–12 4.
AT-75_e.book 33 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Performing with an Active Expression Voice For “Active Expression Voices,” operating the expression pedal will control not only the volume but also the tone, or may add additional sounds. 1. Press the [Others] button of the Part to which you want to assign an Active Expression voice. The voice name appears in the display. Selecting and Playing Sounds The indicator of the selected [Others] button will light. 2.
AT-75_e.book 34 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Adjust the Volume Balance The ATELIER allows you to adjust the volume balance individually for each Part. fig.02-13 The following buttons are used to adjust the volume of a multiple number of Parts.
AT-75_e.book 35 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Transpose the Pitch in Octave Units (Octave Shift) The pitch of the sound played by the keyboard can be adjusted in one-octave steps. This function is called “Octave Shift.” You can apply an Octave shift to the following 4 Parts: • The Upper Part • The Lower Part • The Pedal bass Part Selecting and Playing Sounds • The Solo Part 1. Press the [Utility] button. 2. Press the Menu [ ] [ select “Octave Shift.” 3.
AT-75_e.book 36 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Sustaining Notes Played on the Lower Keyboard You can have the sound for keys in the Lower keyboard continue to play, even after you release the key, until the next key is pressed. 1. Hold down the Pedal [To Lower] button for several seconds until its indicator begins blinking. This setting is saved to the Registration. Pedal [To Lower] button will also turn on at this time. The following message will appear.
AT-75_e.book 37 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Changing the Drums/SFX Set NOTE Immediately after the power is turned on, the STANDARD drum set will sound. Let’s try selecting a different Drum Set or the Sound Effect set. As the drum set, you can choose from 7 types of drum set. When you change the drum set, the sound produced by each note will change. For some drum sets, there will be keys that do not sound. fig.02-19 1. Press the [Drums/SFX] button (indicator lights). 2.
AT-75_e.book 38 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Using the Lower Keyboard to Play the Bass Voice (Bass Split) By using the Bass Split function you can play the bass voice in the left-hand side (including C3) of the lower keyboard. The location at which the lower keyboard is divided in this way, to play the pedal bass voice, is called the “Bass Split Point.” 1. Select a Pedal Bass voice (p. 25). 2. Press the [Utility] button. 3. Press the Menu [ ] [ select “Bass Split.” 4.
AT-75_e.book 39 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Changing the Bass Split Point You can assign the Bass Split Point (the highest key up to which the Pedal Bass voice will sound), to any key of the Lower keyboard. Press the [Utility] button. 2. Press the Menu [ ] [ ] buttons a number of times to select “Bass Split Point.” 3. Press the Value [-] [+] buttons to modify the Bass Split Point. Selecting and Playing Sounds 1.
AT-75_e.book 40 ページ ２００８年８月２１日 木曜日 午前１０時９分 Selecting and Playing Sounds Using the Lower Keyboard to Play the Bass Voice (Pedal [To Lower] button) By using the Pedal [To Lower] button, you can sound the Pedal Bass voice by playing the root note (p. 128) of a chord on the Lower keyboard in the area that is playing the Lower voice. fig.05-08 NOTE If no portion of the Lower keyboard is sounding the Lower voice (the [Drums/SFX] button is ON), the Pedal Bass voice will not sound. NOTE 1.
AT-75_e.book 41 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance The ATELIER lets you enjoy playing along with a rhythmic accompaniment. Selecting a Rhythm The AT-75 provides 40 types of Rhythms and Automatic Accompaniments (Music Styles). These are organized into eight groups. Each Rhythm button corresponds to two groups. By pressing a button that is lit, you can select that button’s other group.
AT-75_e.book 42 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Using Rhythms Stored in User Memory The ATELIER features a User memory. What is User Memory? “User Memory” refers to an area inside the instrument where you can store the Registration you create and the performances you record. Registration and SMF music files saved on USB memory can also be copied to User memory (p. 53). User memory is quite useful, since anything you place there will be retained even while the power is turned off.
AT-75_e.book 43 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Playing Rhythm There are two ways to start the Rhythm. You can press the [Start/Stop] button to start the Rhythm, or you can use Sync Start to have the Rhythm start when you play the lower keyboard or the pedalboard. You can also make the Rhythm start with an intro, or stop with an ending. fig.02-03_AT-900.
AT-75_e.book 44 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Starting the Rhythm Automatically When You Play the Lower Keyboard or Pedalboard (Sync Start) Starting with an Added Intro 1. While holding down the Arranger [On/Off] button, press [Auto Fill In] button to turn Sync Start on. The [Start/Stop] button indicator will blink. 2. Press the [Intro/Ending] button. The [Intro/Ending] button indicator will light. 3. Play either the Lower keyboard or the pedalboard.
AT-75_e.book 45 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Stopping the Rhythm Stopping with an Ending 1. Press the [Intro/Ending] button. An Ending is played, then the Rhythm stops. While the Ending is playing, the [Intro/Ending] button indicator will light, until the Ending finishes the button indicator will be turned off. The functions of the [Intro/ Ending] button and [Start/Stop] button can be assigned to the foot switches located on each side of the Expression Pedal (p. 70).
AT-75_e.book 46 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Changing a Tempo of Rhythm and Automatic Accompaniment You can change the tempo of the Rhythm or Automatic Accompaniment. fig.03-06(P.40) 1. Press the Tempo [ ] [ ] buttons to change the tempo (speed) of the Rhythm or Automatic Accompaniment. Tempo [ ] button The tempo becomes slower Tempo [ ] button The tempo becomes faster The value of the tempo currently set (20–500 beats per minute) can be checked in the display.
AT-75_e.book 47 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Playing Rhythm and Automatic Accompaniment The Arranger function of the ATELIER can add an Automatic Accompaniment to each Rhythm. Based on the selected Rhythm, the Arranger function automatically adds an accompaniment that is suitable for the chord being pressed on the Lower keyboard. fig.02-06.eps 1. Press the Arranger [On/Off] button (indicator lights). 2.
AT-75_e.book 48 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Adding Variety to the Rhythm or Automatic Accompaniment You can add variety to the Rhythm or Automatic Accompaniment by changing the Rhythm pattern. fig.02-07_AT-900.eps Button name [Auto Fill In] button Function A fill-in will automatically be added when you press a Variation [1]–[4] button to change the accompaniment or Rhythm arrangement.
AT-75_e.book 49 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Turning Chord Intelligence On/Off “Chord Intelligence” is a feature that intelligently plays the correct accompaniment chords the moment you play a key specifying a chord on the Lower keyboard during Automatic Accompaniment. To play a C chord on the Lower keyboard, for example, you usually have to press down the three keys C, E, and G; but with Chord Intelligence, you only have to press the C Key to initiate a C chord accompaniment.
AT-75_e.book 50 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Using the Leading Bass Function When Automatic Accompaniment is used, and the Pedal [To Lower] button is ON, the Pedal Bass voice will normally play the root note (p. 128) of the chord you play on the Lower keyboard. If the Leading Bass function is enabled, the lowest note of the chord you play on the Lower keyboard will then be used as the bass note (the bottom note of the chord).
AT-75_e.book 51 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance A Simple Way to Make Automatic Accompaniment Settings (One Touch Program) When using the Arranger function for Automatic Accompaniment, you can also use the “One Touch Program” function to automatically select panel settings that are appropriate for the selected Rhythm. Using the Rhythm Performance By pressing the [One Touch Program] button, you can make the following settings. • Panel settings (e.g.
AT-75_e.book 52 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Using a Rhythm from a USB Memory The ATELIER contains a variety of Rhythms, but you can also use Rhythms from USB memory or floppy disk to perform Rhythms in an even wider range of styles. Reviewing the Styles on USB Memory 1. 2. NOTE Unauthorized use of commercially available Music Style disk for purposes other than private, personal enjoyment is a violation of applicable laws.
AT-75_e.book 53 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Copying Rhythms User memory (p. 42) already contains Rhythms, but you can replace these Rhythms with Rhythms from USB memory or floppy disk. Rhythms copied from the USB memory into User memory will not be lost even if the power is turned off. It is convenient to copy frequently-used Rhythms into User memory. Copying Rhythms from USB Memory to User Memory Connect the USB memory to the External Memory connector. 2.
AT-75_e.book 54 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance 9. Press the [Rec] button. 10. Press the Value [-] [+] buttons to select the copy-destination number. To cancel the procedure, press the [Display/Exit] button. 11. Press the [Rec] button to copy the Rhythm. While the Rhythm is being copied into internal memory, the following screen will be displayed. NOTE If you select a number in which a Rhythm is already saved, a screen like the following appears.
AT-75_e.book 55 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Rhythm Performance Deleting Saved Rhythm You can delete Rhythms stored in User memory (p. 42) or USB memory. Select the Rhythm you want to delete (p. 42). 2. Press the [Load] button and [Save] button simultaneously. Using the Rhythm Performance 1. The following display appears. fig.02-10.eps To cancel the procedure, press the [Reset] button. 3. Press the [Rec] button. While the Rhythm is being deleted, the following screen will be displayed.
AT-75_e.book 56 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons The ATELIER allows you to store sound settings and panel settings such as 4 in the Registration buttons. There are a total of 4 Registration buttons, and one set of panel settings can be stored in each, allowing you to register a total of 4 different panel settings. Each set of panel settings that has been stored in a Registration button is called a “Registration.
AT-75_e.book 57 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Procedure for Creating Registration Sets Prepare the Registrations A convenient way to make the sequence of Registration buttons to be pressed easy to understand is to store the panel settings starting from the Registration [1] button, continuing with subsequent buttons in accordance with the progression of the song.
AT-75_e.book 58 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Recalling a Registration There are two ways of calling up the settings affecting the Rhythms registered to the Registration buttons [1]–[4], “INSTANT” and “DELAYED.” At the factory this is set to “DELAYED.” How to Recall a Registration Recalling Voices and Other Panel Settings 1. Press a Registration [1]–[4] button. Recalling Settings for Rhythm and Automatic Accompaniment in Addition to the Panel Settings 1.
AT-75_e.book 59 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Automatically Registering When You Switch Panel Settings When the [Manual] button is ON (lit), all panel settings you make will be stored automatically in the [Manual] button as they are made, thus updating the Registration that had been previously saved. If you change to a preset Registration [1]– [4] button, it is possible to return to the previous panel settings by pressing the [Manual] button.
AT-75_e.book 60 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons 2. Press the [Registration] button and [Media] button simultaneously. 3. Press the Menu [ ] [ ] buttons to move the cursor, and press the Value [-] [+] buttons to select a character. fig.07-05 The following characters can be selected when changing a name: . space ! " # % & ' ( ) * + , - . / : ; = ? ^ _ A B C D E F G H I J K L M N O P Q R STUVWXYZabcdefghijklmnopqrstuvwxyz0123456789 4. [Reset] button Delete a character.
AT-75_e.book 61 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Saving Registration Sets With the settings of Registration buttons [1]–[4] considered as one set, you can store the Registration set to USB memory or User memory. We recommend that complex panel settings or Registrations you wish to keep be saved on USB memory.
AT-75_e.book 62 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons 7. Press the [Save] button to execute the save operation. Saving of the Registration data will begin. When saving ends, the “- - - - - - - - - - - -” in the screen will change to the Registration name that you saved. fig.07-11 If you’ve named the Registration (p. 59), it will be saved with that name.
AT-75_e.book 63 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Loading Previously Saved Registration Sets Into the ATELIER Here’s how to recall a previously saved Registration set from the User memory or USB memory into the memory of the ATELIER. Registrations can be selected in the following two ways. NOTE Loading a Set of Registrations You can load a “set” (a collection of settings for Registration buttons [1]–[4]) from Floppy disk, USB memory or User memory.
AT-75_e.book 64 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Loading an Individual Registration 1. 2. If you want to load a Registration from USB memory, connect your USB memory to the External Memory connector. Press the [Registration] button to make the indicator light. The Registration Select screen appears. 3. Press the [Media] button to select the desired media. If you want to load from the Registration of USB memory, select “Ext Memory.
AT-75_e.book 65 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Deleting a Set of Registrations Here’s how to delete a Registration set that was saved to a USB memory, User memory (p. 42), or floppy disk. 1. Prepare the Registration that you want to delete. If you want to delete Registration data from the USB memory, connect the USB memory to the External Memory connector. 2. Press the [Registration] button to make the indicator light. The Registration Select screen appears. 3.
AT-75_e.book 66 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons Copying Registrations Registrations from USB memory or floppy disk can be copied to User memory. If a Registration saved in USB memory or on a floppy disk is stored in User memory, the stored Registration data will not disappear even when you turn off the power. It is convenient to load frequently-used Registration into User memory. Registrations saved in User memory can also be copied to USB memory (p. 67).
AT-75_e.book 67 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Registration Buttons 8. Press the Value [-] [+] buttons to select the Registration you want to copy. 9. Press the [Rec] button. 10. Press the Value [-] [+] buttons to select the copy-destination number. To cancel the procedure, press the [Display/Exit] button. 11. NOTE Never remove the USB memory or turn off the power while the Registration data is being copied from USB memory into the ATELIER.
AT-75_e.book 68 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Performance Functions Ò Transposing to a Different Key (Key Transpose) You can transpose the key of a performance without having to shift the position of your fingers on the keyboard. This feature is called “Key Transpose.” For example: you may play in the familiar C major scale while your music will sound in any key of your choice. fig.06-01 1. Press the Transpose [-] [+] buttons.
AT-75_e.book 69 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Performance Functions Using the Foot Switch On each side of the expression pedal are two Foot Switches. Different functions are assigned to each of these two foot switches. fig.06-07 With the factory settings, the following functions are assigned to the left and right Foot Switches. Switch the Rotary effect between Fast/Slow.
AT-75_e.book 70 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Performance Functions Setting Changing the Function of the Foot Switch Description You can select any of the following functions and assign them to either Foot Switch on the right or left side of the Expression Pedal. COMP PLAY/STOP The same function as the Composer [Play/Stop] button. Each time you press the Foot Switch, the performance data will play back or stop. 1. Press the [Utility] button. INTRO/ENDING Play an Intro or Ending.
AT-75_e.book 71 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Performance Functions Using the Foot Switch to Switch Registrations (Registration Shift) Setting Description RIGHT + Load Next The right foot switch is dedicated to switching Registrations. The function assigned to the right foot switch cannot be used. Selecting the Registration [4] button and pressing the right foot switch activates the Load Next function, calling up the next Registration saved to the USB memory, User memory, or floppy disk.
AT-75_e.book 72 ページ ２００８年８月２１日 木曜日 午前１０時９分 Using the Performance Functions Adjusting the Overall Volume Using an Expression Pedal You can adjust the entire volume using an Expression Pedal. When you depress the Expression Pedal, the volume increases. The volume decreases as you tilt the pedal back. fig.06-03 Decrease the volume Likewise you can specify whether the Expression Pedal will or will not control the volume during the playback of recorded music data (p. 100).
AT-75_e.book 73 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice The ATELIER allows you to apply various effects to the sounds you play from the keyboard. Adding Harmony to a Melody (Harmony Intelligence) Harmony appropriate for the chord you play in the lower keyboard can be added to the highest note played in the upper keyboard. This function is called “Harmony Intelligence.
AT-75_e.book 74 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Changing the Type of Harmony Intelligence The AT-75 provides six types of harmony intelligence. When you press the [Harmony Intelligence] button, the most appropriate voice(s) will be automatically set. The manner in which notes will sound also depends on the Harmony type. 1. Press the [Harmony Intelligence] button (indicator lights). 2.
AT-75_e.book 75 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Adding Modulation to the Sound (Rotary Effect) Rotary is an effect which simulates the sound of rotating speakers. There is a choice of two settings: Fast and Slow. fig.05-06.eps 1. Select the voice to which you wish to apply the Rotary effect. 2. Press the Rotary Sound [On/Off] button (confirm that its indicator is lit).
AT-75_e.book 76 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Sustain Effect Sustain allows you to add a Sustain effect or decay to each voice after the keys are released. The Sustain effect can be added simultaneously to the Upper (except the Solo Part), Lower, and Pedal Bass voices. NOTE 1. Press the [Utility] button. 2. Press the Menu [ ] [ select the “Sustain.” 3. Press the [Rec] button. 4.
AT-75_e.book 77 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Changing the Sustain Length The sustain length can be set independently (SHORT, MIDDLE (Medium) or LONG) for the Upper and Lower keyboards and Bass Pedalboard. You can make a separate setting for each keyboard. Press the [Utility] button. 2. Press the Menu [ select “Sustain.” 3. Press the [Rec] button. 4. Press the Menu [ select “Length.” ][ ][ ] buttons a number of times to Adding Various Effects to a Voice 1.
AT-75_e.book 78 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Reverb Effect Reverb is an effect that adds a sense of spaciousness to the sound, creating the illusion of playing in a large or small concert hall, a large or small room, a small club, etc. fig.04-07 1. Press the Reverb [▲] or [▼] button to adjust the overall Reverb amount. When you press the Reverb [▲] button, additional Reverb is applied. Pressing the Reverb [▼] button decreases the Reverb level.
AT-75_e.book 79 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Changing the Reverb Type By changing the reverberations of the notes, you can enjoy the atmosphere of performance in a wide variety of different locations. Press the [Utility] button. 2. Press the Menu [ select “Reverb.” 3. Press the [Rec] button. 4. Press the Menu [ ] [ select “Reverb Type.” ][ ] buttons a number of times to ] buttons to a number of times Adding Various Effects to a Voice 1. fig.11-04 5.
AT-75_e.book 80 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Changing the Wall Type By changing the type of reverb you can experience the feeling of performing in various different locations, and by changing the Wall Type (wall material) you can make further adjustments to the way in which reverberation occurs. 1. Press the [Utility] button. 2. Press the Menu [ select “Reverb.” 3. Press the [Rec] button. 4. Press the Menu [ ] [ select “Wall Type.
AT-75_e.book 81 ページ ２００８年８月２１日 木曜日 午前１０時９分 Adding Various Effects to a Voice Changing the Depth of the Reverb You can make independent settings for each Part. Press the [Utility] button. 2. Press the Menu [ select “Reverb.” 3. Press the [Rec] button. 4. Press the Menu [ select “Depth.” ][ ][ ] buttons a number of times to ] buttons a number of times to Adding Various Effects to a Voice 1. fig.11-05 5. Press the Menu [ ] [ ] buttons to select the part whose reverb depth you wish to adjust.
AT-75_e.book 82 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance The internal composer can record performances and play back commercial SMF music files. fig.08-01 What is a Track Button? The recorded performance will be automatically assigned to the three Track buttons according to the recorded part. You can record or play back independently by specifying the desired Track button; for example, when you wish to re-record a track.
AT-75_e.book 83 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Playing Back Performance Songs Stored on USB Memory and SMF Music Files In addition to playing back the music you recorded on the instrument and saved to a USB memory, ATELIER also lets you enjoy a wide variety of commercially available song files, such as defined below. To Play Back Only One Song 1. Prepare the song that you want to play back.
AT-75_e.book 84 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Silencing a Specific Track (Track Mute) The indicators for Track button in which performances were recorded will be lit. By turning off these Track button indicators, you can temporarily silence the sound. This is referred to as “Track Mute.” Recording a Performance You can record the performance that you play. You can also record your performance while playing Rhythms or Automatic Accompaniment. fig.07-12.
AT-75_e.book 85 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Caution If you press the [Rec] button when a song has been selected from the USB memory or floppy disk, the selected song will be completely loaded into the ATELIER and the Composer will enter into the recording standby mode. To record a new song, use the following procedure. Playing Back a Performance Song Here’s how to play back a performance you’ve recorded. fig.08-06 ig.07-12-2.eps 1 1. 1 2, 3 1.
AT-75_e.book 86 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Add a Count Sound to Match the Timing (Count In) In cases such as when you want to perform in time with a song, you can have a count sound played before playback of the song begins, allowing you to synchronize your own performance with the song. Recording Each Part Separately In this method, each part (track buttons) is recorded one after another: first the bass part, then the Lower part, etc.
AT-75_e.book 87 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Re-Recording Erasing a Performance Song You can record over recorded performance data. If you wish to discard your recording and re-record from the beginning, or if you wish to record a new performance, you must erase the previously-recorded data. 3 2 1 4, 5 2 1. 1 Press the [Bwd] button or the [Fwd] button to select the desired measure (bar) when you start recording.
AT-75_e.book 88 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Changing the Name of a Performance Song (Rename) A name is automatically assigned to a performance song that you record. However, at some point you may wish to change the name to something more meaningful. 3 3. Press the Menu [ ][ ] buttons to move the cursor, and press the Value [-] [+] buttons to select a character. The following characters can be selected when changing a name: space ! " # % & ' ( ) * + , - .
AT-75_e.book 89 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance 3. Saving Performance Songs Press the [Media] button to select the media. Select “Ext Memory” to save the data in USB memory, select “Disk” to save it on a floppy disk, or “Favorites” to save it in User memory. The performance data that you recorded will disappear when the power of the ATELIER is turned off.
AT-75_e.book 90 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance If the following screen appears If you select a number at which a performance data has already been saved, the following screen appears. Loading Performance Songs Into the ATELIER fig.E-64-b.eps To re-record a performance song that is stored on a USB memory or floppy disk, you must first load that song into the instrument. If you wish to update the contents of the performance data 1. Press the [Rec] button.
AT-75_e.book 91 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance 4. 5. Press the Value [-] [+] buttons to select the performance song that you wish to load into internal memory. Press the [Load] button. The selected performance data will be loaded into internal memory. Deleting Performance Songs Stored on “Favorites” or the USB Memory You can delete a performance song that was saved onto a “Favorites,” USB memory, or floppy disk.
AT-75_e.book 92 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance 4. Press the [Load] button and [Save] button simultaneously. The following message, asking you to confirm your choice, will be displayed. Layering a New Recording onto SMF Music Files fig.08-10 You can load commercially available SMF music files into the ATELIER, and record your own performance on top of it. During recording, the data you’ve loaded will be played back, while you record your performance.
AT-75_e.book 93 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance 4. Press the Value [-] [+] buttons to select the SMF music files that you wish to load into internal memory. 5. Press the [Load] button. Using Song with a Different Tempo Than That of the Performance Song The selected performance data will be loaded into internal memory. 6. Press the [Bwd] button or the [Fwd] button to select the desired measure (bar) when you start recording.
AT-75_e.book 94 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Copying Performance Song Performance songs and SMF music files from USB memory or floppy disk can be copied to “Favorites” (User memory). If a performance song saved in USB memory or on a floppy disk is stored in “Favorites,” the stored performance song will not disappear even when you turn off the power. It is convenient to load frequently-used performance song into “Favorites.
AT-75_e.book 95 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Enjoying VIMA TUNES Songs Listening to a VIMA TUNES Song You can connect a CD drive (commercially available) and play back CD-ROM produced for VIMA TUNES (sold separately). While playing a VIMA TUNES song, you can play along using recommended tones. VIMA TUNES VIMA TUNES is a Roland specification for music files that contains image and lyric data, allowing you to enjoy songs with lyrics and images simultaneously.
AT-75_e.book 96 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Listening to Songs from Music CD You can connect a commercially available CD drive to the ATELIER and use it to play music CDs. This lets you perform or sing along with the backing of a music CD. NOTE You can’t copy music CD songs to “Favorites.” NOTE It will take a certain amount of time until a music CD can be selected. 1.
AT-75_e.book 97 ページ ２００８年８月２１日 木曜日 午前１０時９分 Record and Playback Your Performance Transposing the Song to a Comfortable Key for Singing You can transpose the song to a key that is more comfortable for you to sing. If you or someone else will be singing along with a song, you can change the key of the song so it’s appropriate for the singer’s range. If you select a different song, the playback transpose settings will return to their factory-set state. 1.
AT-75_e.book 98 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Folder Settings 8. Assign a name to the folder. Rename the folder as described in “Changing the Name of a Folder” (p. 98). Creating a Folder in USB Memory or User Memory You can create folders in a connected USB memory device or in User memory. If you want to create a folder in USB memory, connect the USB memory to the External Memory connector. 9. About folders The ATELIER lets you create up to 99 Registration sets or songs.
AT-75_e.book 99 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Adjusting How the Instrument Responds Adjusting the Initial Touch Sensitivity (Initial Touch) Initial Touch is a function that translates the force used in playing the keys into a directly proportional amount of volume. Changing the Pedalboard Polyphony (Pedal Bass Mode) You can set the Bass Pedalboard to play simultaneous multiple notes or single notes only. 1. Press the [Utility] button. 2.
AT-75_e.book 100 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Changing How the Solo Voice Responds (Solo Mode) You can specify how the Solo voice will respond when more than one key is pressed. 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “Solo Mode.” fig.12-05 Performance Function Settings Changing the Function of the Expression Pedal (Exp.
AT-75_e.book 101 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Function of the Expression Pedal During Playback You can specify whether or not the Expression pedal will function while ATELIER song files are being played back. 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “Exp. Source.” fig.09-06 3. Press the [Rec] button. 4. Press the Menu [ ][ ] buttons a number of times to select “Playback.” 5.
AT-75_e.book 102 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Changing the Sound of the Countdown (Count Down Sound) You can change the sound that is used for the count played at the end of the intro with the Intro Countdown function (p. 46). 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “Count Down Sound.
AT-75_e.book 103 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Registration Transpose Update (Trans. Update) You can specify how the transpose setting will be recalled when you press a Registration [1]–[4] button. 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “Trans. Update” (Transpose Update). Composer Settings Switching the Display of Lyrics On or Off (Lyrics) Some music files have Lyrics included and these Lyrics can be displayed on the screen.
AT-75_e.book 104 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Changing the Key When Playing Back Songs (Playback Transpose) Changing the Metronome Setting (Metronome) SMF Music files or a performance that you recorded can be transposed for playback. This setting determines whether or not the metronome will sound. 1. Press the [Utility] button. 1. Press the [Utility] button. 2. Using the Menu [ ][ ] buttons a number of times to select “Playback Transpose.” 2.
AT-75_e.book 105 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Adjusting the Metronome Volume (Metronome Volume) Changing the Sound of the Metronome (Metronome Sound) You can adjust the volume of the metronome. You can choose one of 4 different sounds for the metronome. 1. Press the [Utility] button. 1. Press the [Utility] button. 2. Using the Menu [ ][ ] buttons a number of times to select “Metronome.” 2. Using the Menu [ ][ ] buttons a number of times to select “Metronome.” 3.
AT-75_e.book 106 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Setting the Beat (Beat) Silencing a Specific Track (Track Mute) This setting determines the beat to be used when recording performance songs. You can temporarily silence sound of a specific track. This is referred to as “Track Mute.” 1. Press the [Utility] button. 1. Press the [Utility] button. 2. Using the Menu [ ][ ] buttons a number of times to select “Beat.” 2.
AT-75_e.book 107 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Assigning Commercial SMF Music Files to the Tracks Track Channel R (Rhythm) 10 A (Accomp) 5, 6, 7, 8, 9, 11, 12, 13, 14, 15, 16 B (Bass) 2 L (Lower) 3 U (Upper) 4 S (Solo) 1 Muting Individual Channels of Performance Data (Channel Mute) You can mute (silence) individual channels of performance data of SMF music files (commercially available). 1. Press the [Utility] button. 2.
AT-75_e.book 108 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Setting the Type of CD To Be Played Back (CD/Audio Type) The ATELIER may be unable to correctly recognize the type of CD being used. In such instances, you can specify the type of CD manually. 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “CD/Audio Type.” ig.
AT-75_e.book 109 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Other Settings Adjust the Standard Pitch (Master Tune) The standard pitch of an instrument is generally considered as the pitch of the middle A note. The “Master Tune” parameter lets you adjust this standard pitch to match the pitch of any other instruments that are playing together with the ATELIER. 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “Master Tune.” 3.
AT-75_e.book 110 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Setting PC Numbers (PC Number) You can specify the Program Change number that will be transmitted from MIDI Out connector when a Registration is selected. MIDI IN Mode This instrument contains two sound generators: one for SMF data playback and one for keyboard performance. 1. Press the [Utility] button. 2. Normally, data received at the MIDI In connector will control only the sound generator for SMF data playback.
AT-75_e.
AT-75_e.book 112 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Using the V-LINK function (V-LINK) The V-LINK function is turned on, and the V-LINK icon appears in the basic screen. fig.09-41.eps Connecting the ATELIER to a V-LINK compatible image device allows you to control the images with the ATELIER. What is the V-LINK? V-LINK ( ) is a function that allows music and images to be performed together.
AT-75_e.book 113 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings You can also use the following procedure to turn the V-LINK function on. 1,2 1. Hold down the [Reset] button and press either the Upper [Full] button or the Upper [Brass] button. Holding down the [Reset] button and pressing the Upper [Full] button switches the instrument to “MODE 1” (p. 112). Holding down the [Reset] button and pressing the Upper [Brass] button switches the instrument to “MODE 2” (p. 112).
AT-75_e.book 114 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Restoring the User Memory to the Original Factory Settings (User Memory Reset) You can restore the User memory to their original factory settings. This function is called “User Memory Reset.” What is User Memory? “User Memory” refers to an area inside the instrument where you can store the Registration you create and the performances you record. Registration and SMF music files saved on USB memory can also be copied to User memory.
AT-75_e.book 115 ページ ２００８年８月２１日 木曜日 午前１０時９分 Various Other Settings Formatting a USB Memory (Format) 7. Press the [Rec] button to start formatting. The process of preparing USB memory or floppy disks so that they can be used with the ATELIER is called “initialization” (formatting). In certain cases, particularly with floppy disks, the media is formatted for a specific type of device. If the media format does not match the ATELIER’s, you will not be able to use that media with the ATELIER. 1.
AT-75_e.book 116 ページ ２００８年８月２１日 木曜日 午前１０時９分 Connecting with External Devices If you want to hook up an external instrument to the ATELIER, then this chapter is for you. Names and Functions of Jacks and Connectors 2 1 3 Connecting Audio Equipment Output Jacks You can connect audio equipment using audio cables (sold separately) and play the sounds from the ATELIER through the speakers on the connected equipment or record your performances on a recording device.
AT-75_e.book 117 ページ ２００８年８月２１日 木曜日 午前１０時９分 Connecting with External Devices If connection to your computer is unsuccessful... Connecting a Computer The following become possible once you connect a USB cable (available separately) between the USB connector located to the lower left of the ATELIER and the USB connector of your computer. • You can use the ATELIER to play sounds from SMF music files played back with MIDI software.
AT-75_e.book 118 ページ ２００８年８月２１日 木曜日 午前１０時９分 Connecting with External Devices Making the Settings for the USB Driver 1. Press the [Utility] button. 2. Press the Menu [ ][ ] buttons a number of times to select “USB Driver.” Connecting MIDI Devices By connecting an external MIDI device and exchanging performance data, you can control the performances on one device from the other. For instance, you can output sound from the other instrument or switch voice on the other instrument. fig.10-12.
AT-75_e.book 119 ページ ２００８年８月２１日 木曜日 午前１０時９分 Connecting with External Devices Making the Connections NOTE To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 1. Turn the volume all the way down on the ATELIER and on the device you’re about to connect. 2. Switch off the power to the ATELIER and the device you’re about to connect. 3.
AT-75_e.book 120 ページ ２００８年８月２１日 木曜日 午前１０時９分 Troubleshooting If the ATELIER does not function in the way you except, first check the following chart. If this does not resolve the problem, consult your dealer or a nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page. Power does not Turn On Check Problem When you press the [Power On] switch, the power doesn’t come on Power cord is not connected correctly. Solution Connect the power cord correctly.
AT-75_e.book 121 ページ ２００８年８月２１日 木曜日 午前１０時９分 Troubleshooting Problem Check Solution Drums/SFX are selected for the Lower keyboard, but you are playing a key to which no drum sound is assigned. Turn the Drums/SFX off or play keys to which drums sounds are assigned. The Lower keyboard will not produce sound while an Intro or Ending is being played. This is not a malfunction. There is no sound from the twelve keys at the right of the lower keyboard The V-LINK function is set “Mode 2.
AT-75_e.book 122 ページ ２００８年８月２１日 木曜日 午前１０時９分 Troubleshooting Problem Even though you press only one key, a multiple number of notes sound Check Solution Page Harmony Intelligence is turned ON. Turn “Harmony Intelligence” off. p. 73 Chord Intelligence is turned ON. Turn “Chord Intelligence” off. p. 49 Transpose is in effect. Simultaneously press the Transpose [-] [+] buttons to cancel the transposition (the Transpose [-] [+] buttons’ indicators will go out). p. 68 The tuning is incorrect.
AT-75_e.book 123 ページ ２００８年８月２１日 木曜日 午前１０時９分 Troubleshooting Registrations do not Switch Correctly Check Problem The Rhythm or Tempo does not change when you press the Registration buttons The settings at which Registrations are recalled (Registration Arranger Update) has been set to “DELAYED.” Solution Set the timing at which the arranger settings are called up (Registration Arranger Update) to “INSTANT.” Page p. 58 p.
AT-75_e.book 124 ページ ２００８年８月２１日 木曜日 午前１０時９分 Troubleshooting Recording is not possible Check Problem Recording is not possible The recorded performance has disappeared Solution If you wish to erase a previously-recorded track and then re-record, press the track button for the desired track to make that button blink before you begin recording. Press the track button for the desired track to make that button indicator blink before you begin recording.
AT-75_e.book 125 ページ ２００８年８月２１日 木曜日 午前１０時９分 Error Message Error Message Meanings Copy Protected. Can’t Save. To protect the copyright, this music file cannot be saved as SMF format. Write-Protected Media. The protect tab of the storage media is set to the Protect (write prohibit) position. Move the tab to the Write (write permit) position and try the operation again. Can’t Save This Song. You can only play the music data. It cannot be saved on a storage media.
AT-75_e.book 126 ページ ２００８年８月２１日 木曜日 午前１０時９分 Chord List ● symbol: Indicates the constituent not of chord. ★ symbol: Chord shown with an “★”can be played by pressing just the key marked with the “★.” Chord 1.
AT-75_e.book 127 ページ ２００８年８月２１日 木曜日 午前１０時９分 Chord List ● symbol: Indicates the constituent not of chord. ★ symbol: Chord shown with an “★”can be played by pressing just the key marked with the “★.” Chord 2.
AT-75_e.book 128 ページ ２００８年８月２１日 木曜日 午前１０時９分 Glossary Arrangement Registration This refers to changes that have been made in an original tune, by adding a new accompaniment or by changing the instruments used. A set of data that specifies the state of the instrument when performing, including sounds and panel settings. Automatic Accompaniment Automatic Accompaniment is Automatic Accompaniment when just a few keys in the lower section of the keyboard are pressed to specify the chord.
AT-75_e.book 129 ページ ２００８年８月２１日 木曜日 午前１０時９分 Music Files That the ATELIER Can Use What Are Music Files? Music files contains musical information such as how long the key for a corresponding pitch is played, the force applied to the key played, and other such information. Performance data is transmitted to the ATELIER from music files saved in USB memory and CD-ROM, and played back without change as songs.
AT-75_e.book 130 ページ ２００８年８月２１日 木曜日 午前１０時９分 Settings That Are Stored After the Power Is Turned Off Settings That Are Stored After the Power is Turned Off Arranger Update Auto Std Tempo (Auto Standard Tempo) Lyrics Master Tune Metronome Sound MIDI IN Mode Registration Shift Send PC Switch Trans. Update (Transpose Update) USB Driver Registration Name Settings That Are Stored In the Registration Buttons Registration Name Registration Shift Arranger Update Trans.
AT-75_e.book 131 ページ ２００８年８月２１日 木曜日 午前１０時９分 MIDI Implementation Chart Roland Organ Model AT-75 Transmitted Function... Basic Channel Date : Sep. 1, 2008 Version : 1.
AT-75_e.book 132 ページ ２００８年８月２１日 木曜日 午前１０時９分 Main Specifications AT-75: MUSIC ATELIER Keyboard Sound Generator Rhythm Upper Keyboard 49 keys (C3–C7) Lower keyboard 49 keys (Waterfall keyboard, C2–C6) Pedalboard 13 keys (C2–C3) Initial Touch Upper, Lower (10 levels for each) Sound Generator Conforms to GENERAL MIDI Level 2, GENERAL MIDI System, GS and XGlite format Max.
AT-75_e.book 133 ページ ２００８年８月２１日 木曜日 午前１０時９分 Main Specifications Speaker Full-range 16 cm x 2 Display 128 x 64 dots backlit LCD Pedals, Switches Expression Pedal, Foot Switch: 2 pcs.
AT-75_e.book 134 ページ ２００８年８月２１日 木曜日 午前１０時９分 Demo Song List For details on how to play the demo songs, refer to “Listening to the Demo Songs” (p.
AT-75_e.book 135 ページ ２００８年８月２１日 木曜日 午前１０時９分 Index A E Active Expression Voice ...................................... 33 Adjuster ............................................................ 20 Arrangement ................................................... 128 Arranger Function ........................................ 47, 51 Arranger Update .............................................. 102 Audio CD .......................................................... 96 Auto Std Tempo (Auto Standard Tempo) .....
AT-75_e.book 136 ページ ２００８年８月２１日 木曜日 午前１０時９分 Index Master Volume ................................................... 17 Metronome ...................................................... 104 Sound ........................................................ 105 Volume ....................................................... 105 MIDI ............................................................... 118 MIDI Devices Connecting ................................................. 118 MIDI IN Mode .......................
AT-75_e.book 137 ページ ２００８年８月２１日 木曜日 午前１０時９分 Index Upper Voice ...................................................... 25 USB ................................................................ 117 USB (MIDI) connector ....................................... 117 USB Driver ...................................................... 118 User Memory ............................................. 42, 114 User Memory Reset .......................................... 114 V Variation .....................................
AT-75_e.book 138 ページ ２００８年８月２１日 Information AFRICA EGYPT Al Fanny Trading Office 9, EBN Hagar Al Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: (022)-418-5531 REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SOUTH AFRICA T.O.M.S. Sound & Music (Pty)Ltd. 2 ASTRON ROAD DENVER JOHANNESBURG ZA 2195, SOUTH AFRICA TEL: (011)417 3400 Paul Bothner(PTY)Ltd.
AT-75_e.
AT-75_e.book 140 ページ ２００８年８月２１日 木曜日 午前１０時９分 For EU Countries This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
* 5 1 5100001499 0 0 0 0 1 4 9 9 - 0 1 * 08-08-1N
