User Manual
16
Operating the DJ-808
Dual Deck Mode Operations
Dual deck mode is a function that lets you simultaneously control both
decks when using decks 1/3 or decks 2/4 to mix two songs.
1. Hold down the [DECK 1] ([DECK 2]) button and press the [DECK
3] ([DECK 4]) button.
* The order in which you press the buttons does not matter.
Dual deck mode turns on; the [DECK] button you pressed rst is blinking,
and the [DECK] button you pressed later is lit.
The deck indications (the illumination color of the performance pads and
buttons) show the status of the deck whose [DECK] button you pressed
rst.
2. To exit dual deck mode, press the [DECK 1] ([DECK 2]) button or
[DECK 3] ([DECK 4]) button.
Dual deck mode turns o, and the [DECK] button is lit.
The deck switches to the deck of the [DECK] button.
Functions that can be controlled in dual deck mode
Controller Function
Jog dial Scratch, pitch bend, skip mode, slip scratch
[SLIP] button Slip mode, VINYL mode
[AUTO LOOP] button Auto loop, loop active, slip auto loop
LOOP [1/2X] button
Select auto loop beat, change loop length, move loop
LOOP [2X] button
LOOP [IN] button Loop in, change loop in point, select loop slot, slip manual loop
LOOP [OUT] button Loop out, Change loop out point, re-loop/exit, slip manual loop
[HOT CUE] button Hot cue mode, Cue loop mode, Saved ip mode
[ROLL] button Roll mode, Slicer mode, Saved loop mode
[TR] button TR mode, Pattern mode, TR velocity mode
[SAMPLER] button Sampler mode, Pitch play mode, Velocity sampler mode
Performance pads All performance pad operations
PARAMETER [–] [+] buttons
Select loop roll beat, specify length of region and quantize setting
for slicer, change loop length, move loop
[
r] button
Play, pause, slip braking
[CUE] button Cue settings, back cue, cue sampler
[SYNC] button Sync, sync o
[CENSOR] button Censor, reverse
[KEY SYNC] button Key sync, key lock
[UP], [DOWN] buttons Key sync key setting, key lock range setting
Song Analysis
Song analysis begins when you press the DJ-808’s [LOAD] button to load
a song into a deck, but if you’re using Serato DJ as an oine player (i.e.,
without the DJ-808 being connected), you can analyze songs ahead of
time.
If analysis is nished for a song, the BPM and waveform are displayed
immediately after you load that song into a deck.
For details on how to analyze songs with the oine player, refer to the
Serato DJ owner’s manual.
* Depending on the number of songs, analysis might take some time.
Eect Operations
Serato DJ has two eect units (FX1, FX2) which you can use with the
selected deck.
DJ-FX panel
When you click “FX” in the upper left of Serato DJ’s main screen, the DJ-FX
panel opens.
Multi FX mode
You can select up to three eects for each eect unit.
1 1 1 2 3
4 5 4 5 4 5
Single FX mode
You can select one eect for each eect unit, and control multiple
parameters of the selected eect.
1
2 3
4 5 6 6 6 6
1
Currently selected eect type
2
Time at which the eect is applied
3
Number of the deck that uses the eect unit is highlighted
4
Eect on/o status (highlighted when on)
5
Eect depth
6
Eect parameters and settings
Multi FX Mode Operations
1. Hold down the [SHIFT] button and press the [TAP] button to
select multi FX mode.
Each time you press the button, you alternate between multi FX mode
and single FX mode.
2. Press the [1] or [2] button of the deck (channel) that you want
to operate, to select the eect unit that will be used.
In the DJ-FX panel of the Serato DJ screen, the number of the deck that
uses the eect unit is highlighted.
3. Hold down the [SHIFT] button and press an eect button to
select the eect type.
The eect type changes each time you press the button.
4. Press the eect button to turn the eect on (button lit).
5. Use the eect parameter knobs to adjust the eect depth.
6. Use the [BEATS] knob to adjust the time at which the eect is
applied.
* If you press the knob, the setting is set to “1.”