FBM-1_e1.
FBM-1_e1.book 2 ページ 2007年1月5日 金曜日 午後2時41分 Thank you, and congratulations on your choice of the BOSS FBM-1 Bassman. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). These sections provide important information concerning the proper operation of the unit.
FBM-1_e1.book 3 ページ 2007年1月5日 金曜日 午後2時41分 Main Features ● Uses COSM technology to model the amp sound of a Fender® BASSMAN®. ● Makes it easy for you to enjoy that vintage Fender® amp sound simply by connecting the FBM-1 to your usual guitar amp. ● Provides a BRIGHT input like the one on an actual BASSMAN® amp. About the Fender® BASSMAN® fig.bassman.eps In 1951, Fender® introduced the first commercially successful electric bass—the Precision Bass®. The amp developed along with it was the BASSMAN®.
FBM-1_e1.book 4 ページ 2007年1月5日 金曜日 午後2時41分 Panel Descriptions 1. AC Adaptor Jack fig.FBM-1-name1.eps 1 2 6 3 4 5 4 This jack accepts the connection of an AC adaptor (optionally available BOSS PSA-series). By using an AC adaptor, you can play without being concerned about how much battery power you have left. * Use only the specified AC adaptor (PSAseries), and make sure the line voltage at the installation matches the input voltage specified on the AC adaptor’s body.
FBM-1_e1.book 5 ページ 2007年1月5日 金曜日 午後2時41分 Panel Descriptions 2. CHECK Indicator 5. Thumbscrew This indicator shows whether the effect is on or off, and also doubles as the battery check indicator. The indicator lights when the effect is on. * If you’re powering the unit with a battery and the CHECK indicator goes dim—or doesn’t light at all—when you try to turn the effect on, the battery is near depletion and should be replaced.
FBM-1_e1.book 6 ページ 2007年1月5日 金曜日 午後2時41分 Panel Descriptions 10. TREBLE Knob fig.FBM-1-name2.eps 7 8 9 10 11 12 This knob controls the tone of the effect at higher frequencies. 11. LEVEL Knob This adjusts the volume of the effect sound. * No sound is output when this knob is turned completely counterclockwise. 7. PRESENCE Knob This adjusts the sound quality of the ultrahigh range. 8. MIDDLE Knob This knob controls the tone of the effect at middle frequencies. 9.
FBM-1_e1.book 7 ページ 2007年1月5日 金曜日 午後2時41分 Connections * Inserting a connecting plug into the INPUT jack or the BRIGHT IN jack turns on the power to the unit. * Raise the amp volume only after turning on the power to all connected devices. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type.
FBM-1_e1.book 8 ページ 2007年1月5日 金曜日 午後2時41分 Connections Recommended Settings fig.FBM-1-connect-e.eps AC Adaptor BOSS PSA-series (option) 9V DC/200 mA Electric Guitar Guitar Amplifier (JC-120 etc.) * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power-up is required before the unit will operate normally.
FBM-1_e1.book 9 ページ 2007年1月5日 金曜日 午後2時41分 Connections Recommended Settings for the Roland JC-120 Recommended Settings for a Stack Amp MIN MAX MIN PRESENCE MAX TREBLE MIN MAX MIDDLE MIN MAX BASS Set to OFF Recommended Settings for a Fender® Combo Amp We recommend using a clean setting (no distortion) on the connected amp.
FBM-1_e1.book 10 ページ 2007年1月5日 金曜日 午後2時41分 Operating the Unit fig.FBM-1-operation1.eps fig.FBM-1-operation2.eps 1. After you have made the necessary connections (p. 7, p. 8), set the panel knobs as shown in the illustration. 3. Adjust the gain (the amount of distortion) with the GAIN knob. * Setting both knobs at extremely high levels may also result in increased noise. 2. Depress the pedal switch to turn the effect on. (The CHECK indicator lights when the effect is on.
FBM-1_e1.book 11 ページ 2007年1月5日 金曜日 午後2時41分 Operating the Unit fig.FBM-1-operation3.eps fig.FBM-1-operation4.eps 4. Adjust the tone with the BASS knob, MIDDLE knob, TREBLE knob, and PRESENCE knob. 5. Adjust the output volume with the LEVEL knob. Normally, you should adjust the LEVEL knob so there’s no difference in the volume when switching the effect on and off.
FBM-1_e1.book 12 ページ 2007年1月5日 金曜日 午後2時41分 Changing the Battery When the indicator goes dim or no longer lights while the effect is on, it means that the battery must be replaced. Replace the battery following the steps below. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type. fig.replace-battery.
FBM-1_e1.book 13 ページ 2007年1月5日 金曜日 午後2時41分 Troubleshooting The power won’t come on/ the CHECK indicator doesn’t light ● Is the specified adaptor (PSA-series, sold separately) properly connected? Check the AC adaptor connection (p. 7, p. 8). * Never use any AC adapter other than one specified for use with the FBM-1. ● Is the battery low or dead? Replace it with a new battery (p. 12). * The battery that is supplied with the unit is for temporary use, intended primarily for testing the pedal’s operation.
FBM-1_e1.book 14 ページ 2007年1月5日 金曜日 午後2時41分 Setting Samples Standard Crunch Sound Hard Overdrive Sound fig.FBM-1-sample1.eps fig.FBM-1-sample1.eps Mild Crunch Sound Bright Clean Sound fig.FBM-1-sample1.eps fig.FBM-1-sample1.
FBM-1_e1.book 15 ページ 2007年1月5日 金曜日 午後2時41分 Setting Memo fig.FBM-1-memo.eps fig.FBM-1-memo.eps fig.FBM-1-memo.eps fig.FBM-1-memo.
FBM-1_e1.book 16 ページ 2007年1月5日 金曜日 午後2時41分 Setting Memo fig.FBM-1-memo.eps fig.FBM-1-memo.eps fig.FBM-1-memo.eps fig.FBM-1-memo.
FBM-1_e1.book 17 ページ 2007年1月5日 金曜日 午後2時41分 Specifications FBM-1: Bassman Nominal Input Level:....................... -20 dBu Input Impedance:.............................. 1 MΩ Nominal Output Level:.................... -20 dBu Output Impedance: .......................... 2.2 kΩ Recommended Load Impedance:... 10 kΩ or greater Controls:............................................. Pedal switch, PRESENCE knob, MIDDLE knob, BASS knob, TREBLE knob, GAIN knob, LEVEL knob Indicators:............................
FBM-1_e1.book 18 ページ 2007年1月5日 金曜日 午後2時41分 Specifications Weight: ............................................... 440 g /1 lb (including battery) Accessories......................................... Owner’s manual, leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”), dry battery/9 V type (6LR61) * The battery that is supplied with the unit is for temporary use, intended primarily for testing the unit’s operation. We suggest replacing this with an alkaline dry cell. Option ............
FBM-1_e1.book 19 ページ 2007年1月5日 金曜日 午後2時41分 For EU Countries This product complies with the requirements of European Directive 89/336/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FBM-1_e1.