Owner's Manual Digital Piano FP-2
Table Of Contents
- USING THE UNIT SAFELY
- IMPORTANT NOTES
- Contents
- Panel Descriptions
- Before You Play
- Chapter 1 Playing the Keyboard
- Listening to Demo Songs
- Listening to Internal Songs
- Performing with a Variety of Sounds
- Performing With Two Layered Tones (Dual Play)
- Performing With Different Tones in the Left and Right Sides of the Keyboard (Split Play)
- Changing the Volume Balance for Dual Play and Split Play
- Changing the Keyboard’s Touch
- Adding Reverberation to Sounds (The Reverb Effect)
- Adding a Variety Effects to the Sound
- Transposing the Key of the Keyboard (Key Transpose)
- Using the Metronome
- Boosting the Low-Frequency Range (Sound Control)
- Changing the Tonal Quality (Equalizer)
- Chapter 2 Playing Along with Rhythms
- What is Session Partner?
- Performing Along With Session Partner
- Selecting a Rhythm
- Changing a Rhythm’s Tempo
- Selecting a Rhythm’s Chord Progression
- Performing With the Chord Progression Specified in the Left Hand (Chord Progression off)
- Recording the Chord Progression (Chord Progression)
- Storing Settings (Setup)
- Chapter 3 Recording a Performance
- Chapter 4 Other Functions
- How to Make Settings
- Changing How the Pedal Effects Are Applied
- Changing How the Pedals Work
- Changing the Effect Type
- Setting the Part to Which Effects Are Added
- Changing the Pitch of the Lower Tone in Octave Steps (Octave Shift)
- Tuning to Other Instruments’ Pitches (Master Tuning)
- Adjusting the Tuning (Temperament)
- Changing the Beat of Metronome
- Setting the Intro and Ending On or Off
- Fixing a Set Chord Progression
- Setting the Root Note of the Chord Progression
- Setting the Chord Display On or Off
- Changing the Equalizer Settings
- Connecting to Audio Equipment
- About the FP-2 Sound Generator
- Connecting to the USB Connector
- Connecting MIDI Devices
- Using the V-LINK function
- Making the Settings for the USB Driver
- Restoring the Settings to the Factory Condition (Factory Reset)
- Disabling Everything Except Piano Play (Panel Lock)
- Troubleshooting
- Error Messages/Other Messages
- Tone List
- Rhythm List
- Chord Progression Pattern List
- Chord Fingering List
- Internal Song List
- Settings Stored in the Setup
- Easy Operation List
- MIDI Implementation Chart
- Main Specifications
- Index
18
Chapter 1 Playing the Keyboard
■
Changing the Keyboard’s Split Point
You can change the location where the keyboard is divided (the split point)
within the range of B1 through B6.
This is set to “F 3” when the instrument is turned on.
This setting remains in effect until you turn off the power.
fig.01-14
1.
Hold down the [Split] button and press a key set as the split
point.
The key you pressed becomes the split point, and appears in the display.
The key being used as the split point belongs to the left-hand section of the
keyboard.
When you release the [Split] button, you return to the previous screen.
Changing the Volume Balance for Dual
Play and Split Play
You can change the volume balance of the Upper and Lower Tones in Dual
Play (p. 15) and Split Play (p. 16).
fig.01-15
1.
Use the [Balance] knob to adjust the volume balance.
F 3
B1 B6
The name of the key acting
as the split point is
indicated in the display, as
shown below.
Display
Letter
name
Display
Letter
name
Display
Letter
name
C d_ d E_
C D D E
E F F G
E F F G
A_ A b_ b
A A B B
FP-2_e.book 18 ページ ２００４年１１月２６日 金曜日 午後４時２５分