Owner's Manual Digital Piano FP-2
Table Of Contents
- USING THE UNIT SAFELY
- IMPORTANT NOTES
- Contents
- Panel Descriptions
- Before You Play
- Chapter 1 Playing the Keyboard
- Listening to Demo Songs
- Listening to Internal Songs
- Performing with a Variety of Sounds
- Performing With Two Layered Tones (Dual Play)
- Performing With Different Tones in the Left and Right Sides of the Keyboard (Split Play)
- Changing the Volume Balance for Dual Play and Split Play
- Changing the Keyboard’s Touch
- Adding Reverberation to Sounds (The Reverb Effect)
- Adding a Variety Effects to the Sound
- Transposing the Key of the Keyboard (Key Transpose)
- Using the Metronome
- Boosting the Low-Frequency Range (Sound Control)
- Changing the Tonal Quality (Equalizer)
- Chapter 2 Playing Along with Rhythms
- What is Session Partner?
- Performing Along With Session Partner
- Selecting a Rhythm
- Changing a Rhythm’s Tempo
- Selecting a Rhythm’s Chord Progression
- Performing With the Chord Progression Specified in the Left Hand (Chord Progression off)
- Recording the Chord Progression (Chord Progression)
- Storing Settings (Setup)
- Chapter 3 Recording a Performance
- Chapter 4 Other Functions
- How to Make Settings
- Changing How the Pedal Effects Are Applied
- Changing How the Pedals Work
- Changing the Effect Type
- Setting the Part to Which Effects Are Added
- Changing the Pitch of the Lower Tone in Octave Steps (Octave Shift)
- Tuning to Other Instruments’ Pitches (Master Tuning)
- Adjusting the Tuning (Temperament)
- Changing the Beat of Metronome
- Setting the Intro and Ending On or Off
- Fixing a Set Chord Progression
- Setting the Root Note of the Chord Progression
- Setting the Chord Display On or Off
- Changing the Equalizer Settings
- Connecting to Audio Equipment
- About the FP-2 Sound Generator
- Connecting to the USB Connector
- Connecting MIDI Devices
- Using the V-LINK function
- Making the Settings for the USB Driver
- Restoring the Settings to the Factory Condition (Factory Reset)
- Disabling Everything Except Piano Play (Panel Lock)
- Troubleshooting
- Error Messages/Other Messages
- Tone List
- Rhythm List
- Chord Progression Pattern List
- Chord Fingering List
- Internal Song List
- Settings Stored in the Setup
- Easy Operation List
- MIDI Implementation Chart
- Main Specifications
- Index
52
Troubleshooting
Pedal Has No
Effect, or Effect
“Sticks”
Is the pedal connected correctly?
Connect the pedal securely to the Pedal
jack (p. 9).
Are you using a pedal made by another
manufacturer? Use the pedal included
with the FP-2 or an optional DP Series or
similar pedal.
Unplugging a pedal cord from the unit
while the power is on may cause the
pedal’s effect to be applied nonstop.
Be sure to switch off the power to the unit
before attempting to disconnect or connect
a pedal cord (p. 9).
Once it’s been assigned as a setup switch, a
soft pedal or sostenuto pedal cannot be
used for its original function (p. 48).
Sound Suddenly
Changes at Key in
Upper Octaves
With the acoustic piano settings, sounds in
the upper 1 1/2-octave range are extended
to the end regardless of the damper pedal
actions. The tone is also different in this
range. Roland’s pianos faithfully
reproduce the sonic qualities of acoustic
pianos. Furthermore, you can use the
instrument’s Key Transpose setting to
change that range over which the damper
pedal has no effect.
High-Pitched
Whine is Produced
When listening through headphones:
Certain piano tones that feature
vibrant, sparking sounds contain a
large high-frequency component,
which may make it appear that a
metallic reverberation has been
applied. This faithfully reproduces the
characteristics of acoustic pianos, and
does not indicate any malfunction.
Since this reverberation becomes
particularly audible when
supplemented by heavy reverb, you
may be able to diminish the problem by
reducing the amount of reverb applied
to the sound.
When listening through speakers:
Here, a different cause (such as
resonance produced by the FP-2) would
be suspect. Consult your Roland dealer
or nearest Roland Service Center.
Case Cause/What to do
Low End Sounds
Are Strange/Have
a Rattling Sound
When listening through speakers:
Playing at loud volumes may cause
instruments near the FP-2 to resonate.
Resonation can also occur with
fluorescent light tubes, glass doors, and
other objects. In particular, this problem
occurs more easily when the bass
component is increased, and when the
sound is played at higher volumes. Use
the following measures to suppress
such resonance.
- Place speakers so they are 10–15 cm
from walls and other surfaces.
- Reduce the volume.
- Move the speakers away from any
resonating objects.
- Check to make sure that the screws
holding the music stand in place are
not loose.
When listening through headphones:
The cause lies somewhere else. Consult
your Roland dealer or nearest Roland
Service Center.
With certain tones, the sounds may seem
to be distorted.
The volume level
of the instrument
connected to Line
In Jack is too low
Could you be using a connection cable that
contains a resistor?
Use a connection cable that does not
contain a resistor.
Case Cause/What to do
FP-2_e.book 52 ページ ２００４年１１月２６日 金曜日 午後４時２５分