Owner's Manual Digital Piano FP-2
Table Of Contents
- USING THE UNIT SAFELY
- IMPORTANT NOTES
- Contents
- Panel Descriptions
- Before You Play
- Chapter 1 Playing the Keyboard
- Listening to Demo Songs
- Listening to Internal Songs
- Performing with a Variety of Sounds
- Performing With Two Layered Tones (Dual Play)
- Performing With Different Tones in the Left and Right Sides of the Keyboard (Split Play)
- Changing the Volume Balance for Dual Play and Split Play
- Changing the Keyboard’s Touch
- Adding Reverberation to Sounds (The Reverb Effect)
- Adding a Variety Effects to the Sound
- Transposing the Key of the Keyboard (Key Transpose)
- Using the Metronome
- Boosting the Low-Frequency Range (Sound Control)
- Changing the Tonal Quality (Equalizer)
- Chapter 2 Playing Along with Rhythms
- What is Session Partner?
- Performing Along With Session Partner
- Selecting a Rhythm
- Changing a Rhythm’s Tempo
- Selecting a Rhythm’s Chord Progression
- Performing With the Chord Progression Specified in the Left Hand (Chord Progression off)
- Recording the Chord Progression (Chord Progression)
- Storing Settings (Setup)
- Chapter 3 Recording a Performance
- Chapter 4 Other Functions
- How to Make Settings
- Changing How the Pedal Effects Are Applied
- Changing How the Pedals Work
- Changing the Effect Type
- Setting the Part to Which Effects Are Added
- Changing the Pitch of the Lower Tone in Octave Steps (Octave Shift)
- Tuning to Other Instruments’ Pitches (Master Tuning)
- Adjusting the Tuning (Temperament)
- Changing the Beat of Metronome
- Setting the Intro and Ending On or Off
- Fixing a Set Chord Progression
- Setting the Root Note of the Chord Progression
- Setting the Chord Display On or Off
- Changing the Equalizer Settings
- Connecting to Audio Equipment
- About the FP-2 Sound Generator
- Connecting to the USB Connector
- Connecting MIDI Devices
- Using the V-LINK function
- Making the Settings for the USB Driver
- Restoring the Settings to the Factory Condition (Factory Reset)
- Disabling Everything Except Piano Play (Panel Lock)
- Troubleshooting
- Error Messages/Other Messages
- Tone List
- Rhythm List
- Chord Progression Pattern List
- Chord Fingering List
- Internal Song List
- Settings Stored in the Setup
- Easy Operation List
- MIDI Implementation Chart
- Main Specifications
- Index
8
Before You Play
Making Connections
1.
Before you begin making connections, confirm the following.
Is the volume level of the FP-2 turned all the way down?
Is the power to the FP-2 turned off?
2.
Connect the supplied Power Cord to the supplied AC
adaptor.
fig.00-01
3.
Connect the supplied AC adaptor to the FP-2, and then plug
its other end into a power outlet.
4.
Loop the AC adaptor cord around the cord hook to fasten it
in place.
fig.00-02
927
To prevent the inadvertent disruption of power to your unit (should the
plug be pulled out accidentally), and to avoid applying undue stress to the
AC adaptor jack, anchor the power cord using the cord hook, as shown in
the illustration.
Depending on the circumstances of a particular setup, you may experience
a discomforting sensation, or perceive that the surface feels gritty to the
touch when you touch this device. This is due to an infinitesimal electrical
charge, which is absolutely harmless. However, if you are concerned about
this, connect the ground terminal (see figure) with an external ground.
When the unit is grounded, a slight hum may occur, depending on the
particulars of your installation. If you are unsure of the connection method,
contact the nearest Roland Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be dangerous in the event of
lightning)
Power outlet
AC adaptor
Power cord
Rear Panel
ground terminal
cord hook
FP-2_e.book 8 ページ ２００４年１１月２６日 金曜日 午後４時２５分