Owner's Manual
USING THE UNIT SAFELY
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices
About the Symbols
ALWAYS OBSERVE THE FOLLOWING
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless you are
instructed to do so in the owner’s manual.
Otherwise, you risk causing malfunction.
Do not repair or replace parts by yourself
Refer all servicing to your retailer, the
nearest Roland Service Center, or an
authorized Roland distributor, as listed on
the “Information.”
Do not use or store in the following types of
locations
• Subject to temperature extremes (e.g.,
direct sunlight in an enclosed vehicle,
near a heating duct, on top of heat-
generating equipment); or are
• Damp (e.g., baths, washrooms, on wet
oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness;
or are
• Placed in a poorly ventilated location.
Do not place in an unstable location
Otherwise, you risk injury as the result of
the unit toppling over or dropping down.
Be cautious to protect children from injury
Always make sure that an adult is on hand
to provide supervision and guidance when
using the unit in places where children
are present, or when a child will be using
the unit.
Do not drop or subject to strong impact
Otherwise, you risk causing damage or
malfunction.
CAUTION
Use only stand manufactured by Roland
This stand for use only with specic Roland
musical instruments. See apparatus
instructions. Use with other models is
capable of resulting in instability causing
possible injury.
Evaluate safety issues before using stands
Even if you observe the cautions given
in the owner’s manual, certain types of
handling may allow this product to fall
from the stand, or cause the stand to
overturn. Please be mindful of any safety
issues before using this product.
Avoid climbing on top of the unit, or placing heavy
objects on it
Otherwise, you risk injury as the result of
the unit toppling over or dropping down.
Keep small items out of the reach of children
To prevent accidental ingestion of the
parts listed below, always keep them out of
the reach of small children.
• Included Parts
Screws
IMPORTANT NOTES
Placement
• Do not allow lighting devices that normally are
used while their light source is very close to the unit
(such as a piano light), or powerful spotlights to
shine upon the same area of the unit for extended
periods of time. Excessive heat can deform or
discolor the unit.
• Do not paste stickers, decals, or the like to this
instrument. Peeling such matter o the instrument
may damage the exterior nish.
• Depending on the material and temperature of the
surface on which you place the unit, its rubber feet
may discolor or mar the surface.
Maintenance
• To clean the unit, use a dry, soft cloth; or one that
is slightly dampened. Try to wipe the entire surface
using an equal amount of strength, moving the
cloth along with the grain of the wood. Rubbing
too hard in the same area can damage the nish.
• Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
• As with any wood-crafted product, some expansion
and contraction of the wood can occur depending
on the way the unit is used and the environment
in which it is used. Over time, this can cause some
of the screws to start coming loose. To ensure safe,
worry-free use of the unit, you should periodically
check the tightness of the screws shown in the
illustration. If you nd any that are loose, use a
screwdriver to tighten them.
Copyright © 2015 ROLAND CORPORATION
Before using this stand, carefully read the sections entitled “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” Additionally this manual
should be saved and kept on hand as a convenient reference.
5
Make sure that another person is on hand to help with the assembly and setup.
5 Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet.
5 Prepare an area in which you can perform the assembly safely.
5 Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the
screws.
5 The KSC-70 is designed specically to be used with the FP-30.
Parts Check
Before you begin assembling the stand, check that all the parts ere
supplied.
1
4
3
2
A BC
A Side board (left) 1 pcs.
B Side board (right) 1 pcs.
C Center board 1 pcs.
1 Screw
“a” (M5 x 12 mm) 6 pcs.
2 Stabilizers (left/right)
3 Screw
“b” (4×14 mm) 6 pcs.
4 Screw
“c” (M5 x 20 mm) 4 pcs.
Assembly Procedure
* You will also need to have a Phillips screwdriver.
* Fasten each screw tightly, then place the stand in a stable and horizontal
place.
* Do not allow the pedal cord or power cord to get twisted or pinched while
assembling the stand.
* In the interest of product improvement, the specications and/or appearance
of this stand are subject to change without prior notice.
1
Stand Assembly
At rst, assemble the entire stand in a temporary fashion, without really
tightening the screws. Then, after checking the overall alignment of the
boards (and gently shifting certain parts where necessary), go around
and tightly fasten each of the screws.
1. Attach the side board (left) for the left sides to the center
board (so that the metal parts face inside) using screws “a”
(M5 x 12 mm).
2. Use screws “a” (M5 x 12 mm) to attach the side board (right)
in the same way.
1
2
Center board
Side board (left)
Side board (right)
Position the metal parts
of the center board so
that they face the rear.
Screw “a”
(x 6) *
Front
Rear
Do not use the long screws
“ c .”
2
Attaching the Stabilizers
1. Place the unit upright, and attach the stabilizers to the side
boards.
* Securely fasten the stabilizers to their nal tightness at this time.
Screws “b” (4 x 14 mm):
use six screws
Stabilizers
3
Installing the Piano on the Stand
1. Set the piano on the stand, then rmly attach the four screws
“c” (M5 x 20 mm).
* When handling the piano, rmly grasp it. Be careful, so you do not get your
ngers pinched.
Screw “c” (x 4)
Side board
Underneath the
Piano
Please don’t get your ngers
pinched!
Owner’s Manual
Keyboard stand for FP-30
KSC-70
*5100049638-03*
In the interest of product improvement, the
specications and/or appearance of this unit are subject
to change without prior notice.
11