Specifications

18
M-300
SPECIFICATIONS
M-300
Number of Channels
32 mixing channels/11 buses/4 MATRIX buses/Up to 92
inputs and 90 outputs when using REAC Devices
Input Impedance
CONSOLE INPUT jacks (1 to 4): 14 k ohms
CONSOLE INPUT jacks (5 to 12): 10 k ohms
Output Impedance
CONSOLE OUTPUT jacks (1 to 8): 600 ohms
PHONES jack: 100 ohms
Dimensions
470.0 (W) x 482.7 (D) x 194.9 (H) mm
18-1/2(W) x 19(D) x 7-1/4(H) inches
Weight
9.8 kg
21 lbs 10 oz
Remote Connectors
RS-232C connector: 9-pin D-sub type
MIDI connectors (OUT/THRU, IN): 5-pin DIN type
Other Connectors
Grounding terminal
AC INPUT connector
PROCESSING
CONNECTORS
INPUT/OUTPUT CHARACTERUSTUCS
OTHERS
AD/DA Conversion
24-bit/48.0 kHz or 44.1 kHz
PHONES jack
Stereo 1/4 inch phone type
REAC port
RJ-45 EtherCon type x 2
Power Supply
AC 115 V, 117 V, 220 V, 230 V, 240 V (50/60 Hz)
DIGITAL OUT jack
Optical type
USB port
Type A x 1, Type B x 1
Display
800 x 480 dots Wide VGA TFT color screen with backlight
Power Consumption
50 W
Dynamic Range
CONSOLE OUTPUT jacks (1 to 8):
105 dB (typ.)
Cross Talk@ 1 kHz
CONSOLE INPUT jacks (1 to 4): -80dB (Pad: ON, Input sens:
+4 dBu, typ.)
CONSOLE INPUT jacks (5 to 12): -80dB (Input sens: +4 dBu, typ.)
CONSOLE OUTPUT jacks (1 to 8): -100 dB (typ.)
* Sampling frequency is 48 kHz or 44.1 kHz.
Network Latency
2.8 mS (typ.)
* Total System Latency of audio signal from S-1608 inputs to
outputs via M-300's REAC ports (A or B).
* Sample Rate: 48.0 kHz
* Effects: No insert effects
CONSOLE INPUT
jacks (5 to 8)
1/4 inch Phone type (balanced)
Total Harmonic
Distortion + Noise
CONSOLE OUTPUT jacks (1 to 8): 0.05 % (typ., +4 dBu)
PHONES jack: 0.05 % (typ., 40 ohms load, 130 mW)
CONSOLE INPUT
jacks (1 to 4)
XLR-3-31 type (balanced, phantom power)
CONSOLE OUTPUT
jacks (1 to 4)
XLR-3-32 type (balanced)
CONSOLE INPUT
jacks (9 to 12)
RCA Pin type
Residual Noise
Level (IHF-A, typ.)
-88 dBu (All faders: Min)
CONSOLE OUTPUT
jacks (5 to 8)
1/4 inch Phone type (balanced)
Frequency Response
CONSOLE OUTPUT jacks (1 to 8): -2 dB / +0 dB (20k ohms
load, +4 dBu)
PHONES jack: -3 dB / +0 dB (40 ohms load, 150 mW)
Nominal Input
Level (Variable)
CONSOLE INPUT jacks (1 to 4):
-65 to -10 dBu (Pad: OFF) or
-45 to +10 dBu(Pad: ON)
CONSOLE INPUT jacks (5 to 12):
-28 to +4 dBu
Nominal Output
Level
CONSOLE OUTPUT jacks (1 to 8):
+4 dBu (Load impedance: 10 k ohms)
Recommended
Load Impedance
CONSOLE OUTPUT jacks (1 to 8): 10 k ohms or greater
PHONES jack: 8 ohms or greater
Equivalent Input
Noise Level (E.I.N.)
-126 dBu (Main Fader: Unity, Channel faders: Unity only one
channel, Preamp gain: Max)
Non Clip Maximum
Input level
CONSOLE INPUT jacks (1 to 4):
+8 dBu (Pad: OFF) or +28 dBu
(Pad: ON)
CONSOLE INPUT jacks (5 to 12):
+22 dBu
Non Clip Maximum
Output level
CONSOLE OUTPUT jacks (1 to 8):
+22 dBu (1 kHz, 10 k ohms
load)
PHONES jack:
150 mW + 150 mW (Typ., 1 kHz, 40 ohms load)
(0dBu=0.775Vrms)
* XLR type: 1 GND, 2 HOT, 3: COLD
* phantom power: DC+48V(unloaded maximum), 14mA(maximum load) (All XLR type inputs)
* When a REAC Splitter S-4000D or a switching hub is used in-line with REAC cables, the
network latency will increase by the amount of processing delay introduced by the
splitting device itself. The actual delay is dependant upon the specifications of the
splitting device, though the maximum delay amount for a single splitting device should be
about 200microseconds.
Fugue ©1999-2010 Kyoto Software Research, Inc All right reserved
USB memory recorder/player
470
430 2020
482.7
194.9
475.7
Unit: mm
RA-10U
Rackmount Angle
Rackmountable to 19-inch rack (EIA)
Option
Record the output of the V-Mixer
Main, assigned AUX bus or MATRIX
bus directly to a USB memory drive
connected to the built-in USB port. A
mix produced with the V-Mixer can be
saved as an uncompressed WAV file,
without the need for an external
recorder. WAV files on the USB
memory drive can also be played back
on the V-Mixer and used for back-
ground music/tracks. User settings
and mixer data can also be saved to a
USB memory drive. The USB record-
ing function is available on all V-Mixer
Consoles.