VS-100_install_e.
VS-100_install_e.book 2 ページ ２００９年３月１２日 木曜日 午後６時３分 IMPORTANT NOTES Handling DVD-ROM/CD-ROMs Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty DVD-ROM/CD-ROM discs may not be read properly. Keep your discs clean using a commercially available cleaner. DO NOT play a CD-ROM disc on a conventional audio CD player. The resulting sound may be of a level that could cause permanent hearing loss. Damage to speakers or other system components may result.
VS-100_install_e.book 3 ページ ２００９年３月１２日 木曜日 午後６時３分 About This Manual This manual (SONAR V-STUDIO 100 Getting Started) provides basic information about how to set up the SONAR V-STUDIO 100, make initial settings, and set up your system. It also provides troubleshooting information. ● This manual uses the following icons to call your attention to explanations of terms or to important points you should note. These contain important information, so please be sure to read them.
VS-100_install_e.book 4 ページ ２００９年３月１２日 木曜日 午後６時３分 Contents About This Manual......................................................................................................................................... 3 Checking the Contents of the Package ......................................... 6 Installation and Registration ......................................................... 7 Installing the SONAR V-STUDIO 100 Driver ................................................................................
VS-100_install_e.book 5 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting ...........................................................................41 Problems When Installing Driver or Changing Settings ................................................................42 Problems When Installing SONAR or Changing Settings..............................................................43 Problems at Startup with SONAR...................................................................................................
VS-100_install_e.book 6 ページ ２００９年３月１２日 木曜日 午後６時３分 Checking the Contents of the Package As soon as you open the package, check that you have all of the included items. If anything is missing, contact your dealer. ❏ SONAR V-STUDIO 100 Hardware ■ Getting Started This is the manual you’re reading. It explains how to get SONAR V-STUDIO 100 up and running. It also explains what you need to know when setting up this product, and what you should know when using it.
VS-100_install_e.book 7 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Here’s how to install the SONAR V-STUDIO 100 driver and SONAR on your computer. Please note before installing When installing, you must log on as a user with administrative privileges In order to install SONAR, you must log on as a user who has administrative privileges. Once installed, the program can also be used by users who do not have administrative privileges.
VS-100_install_e.book 8 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Windows Vista Users 1. Disconnect all USB cables (except those for a USB keyboard and/or USB mouse, if used), then start up Windows. 2. Close all currently running software (applications). Also close all windows that are open. If you are using software such as antivirus programs, be sure to close these programs as well. 3. Insert the included “SONAR V-STUDIO 100 Driver CD-ROM” into your computer’s CD/DVD-ROM drive. 4.
VS-100_install_e.book 9 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration 10. Perform the following procedure before you connect the SONAR V-STUIDO 100 hardware to your computer. 1. Minimize the SONAR V-STUDIO 100 hardware’s [MAIN MIX] knob. 2. Connect the included AC adaptor to the SONAR V-STUDIO 100 hardware. Power Cord AC Adaptor DC IN to Power Outlet 3. Turn on the POWER switch of the SONAR V-STUDIO 100 hardware. 4.
VS-100_install_e.book 10 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration 11. The lower right corner of the screen will indicates “Installing device driver software,” and the driver will be installed automatically. * If any other message is displayed, note the contents and close the message. 12. When the “Installation has been completed.” message appears, installation has been completed. Click [Close] to close the “Driver Setup” dialog box. 13.
VS-100_install_e.book 11 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration 6. Click [Next] to begin installation. * If the “Software Installation” dialog box appears, click [Continue Anyway] to proceed with the installation. If the “Driver Signing Options” setting was not set to “Ignore,” a “Hardware Installation” dialog box appears. A dialog box with a “!” symbol appears. 1. Click [Continue Anyway] and continue the installation. A dialog box with a “x” symbol appears. 1. Click [OK]. 2.
VS-100_install_e.book 12 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration 5. Perform the following procedure before you connect the SONAR V-STUIDO 100 hardware to your computer. 1. Minimize the SONAR V-STUDIO 100 hardware’s [MAIN MIX] knob. 2.Connect the included AC adaptor to the SONAR V-STUDIO 100 hardware. Power Cord AC Adaptor DC IN to Power Outlet 3.Turn on the POWER switch of the SONAR V-STUDIO 100 hardware. 4.
VS-100_install_e.book 13 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration 6. Wait until the lower right of the screen indicates “Found New Hardware” and the “Found New Hardware Wizard” appears. * It may take some time for the “Found New Hardware Wizard” to appear. 7. If you are asked whether you want to connect to Windows Update, choose “No” and then click [Next]. 8. Choose “Install the software automatically (Recommended)” and click [Next]. 9.
VS-100_install_e.book 14 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Macintosh Users * Do not connect the SONAR V-STUDIO 100 hardware to your computer until you are directed to do so. * If the Authenticate dialog box or the dialog that indicates “Installer requires that you type your password” appears during the installation, enter your password and click OK. * What you actually see on the screen may differ depending on your system. 1.
VS-100_install_e.book 15 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Installing the software This is a package containing AU and VST compatible plug-ins. It contains a variety of plug-ins including plug-in effects, sample players, and plug-in synthesizers. This is included on the SONAR VS INSTALLATION DVD-ROM, and installation will begin automatically when you insert the DVD-ROM into your computer. For details, refer to the online documentation of the installed plug-ins.
VS-100_install_e.book 16 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Connecting 1. Minimize the SONAR V-STUDIO 100 hardware’s [MAIN MIX] knob. 2. Connect the included AC adaptor to the SONAR V-STUDIO 100 hardware. Power Cord AC Adaptor DC IN to Power Outlet 3. Turn on the POWER switch of the SONAR V-STUDIO 100 hardware. 4. Use the included USB cable to connect the SONAR V-STUDIO 100 hardware to your computer.
VS-100_install_e.book 17 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Connecting your audio equipment Connect your headphones and/or speakers to the SONAR V-STUDIO 100 hardware. * This package does not include sound reproduction equipment such as headphones or speakers. If you connect headphones or monitor speakers as shown in the illustration, you’ll be able to monitor the playback audio.
VS-100_install_e.book 18 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Register SONAR Before you install SONAR, take a minute to register the software so we can let you know when updates become available and provide you with technical support. To register anytime, log onto http://www.cakewalk.com/register, or call 888-CAKEWALK (U.S.) or +1 (617)-423-9004 (outside the U.S.) between 9 AM and 8 PM Eastern Standard Time.
VS-100_install_e.book 19 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Installing SONAR SONAR is easy to install. All you need to do is choose the folder where the program and sample project files should be stored. Before you start, make sure you have your serial number handy. Your serial number is located on the back of the SONAR VS Installation DVD-ROM case. To Install SONAR 1. Start your computer. 2. Close any open programs that are running. 3.
VS-100_install_e.book 20 ページ ２００９年３月１２日 木曜日 午後６時３分 Installation and Registration Running SONAR for the First Time Before SONAR VS can communicate with the SONAR V-STUDIO 100 hardware, you must enable and assign the VS100 MIDI ports in SONAR, then insert the VS-100 control surface plug-in. 1. Power up the SONAR V-STUDIO 100 hardware. 2. The first time you run SONAR, the following message appears: “SONAR VS will now personalize your setting by copying...,” Click [OK]. 3.
VS-100_install_e.book 21 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Audio Driver Settings As described below, configure SONAR so that you can use the SONAR V-STUDIO 100 hardware as an audio driver. You’ll need to make these settings in the following cases. • Immediately after installing SONAR • If you’ve updated the SONAR V-STUDIO 100 driver • If you’ve newly installed the SONAR V-STUDIO 100 driver Keep the SONAR V-STUDIO 100 Hardware Manual at hand.
VS-100_install_e.book 22 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings If the driver is not shown Did you connect the SONAR V-STUDIO 100 hardware before launching SONAR? Is the interface driver installed correctly? Refer to “Installing the SONAR V-STUDIO 100 Driver” (p. 7), and verify that the SONAR V-STUDIO 100 driver is installed correctly. Is the SONAR V-STUDIO 100 hardware correctly connected to your computer? Is the SONAR V-STUDIO 100 hardware powered on? 7. Click “OK” to close the dialog box.
VS-100_install_e.book 23 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Other Audio Driver and Audio-Related Settings You can also set the following options as necessary. • Execute the “Options | Audio” command to open the “Audio Options” dialog box. By clicking the [Help] button in each dialog box, you can view detailed information about each option.
VS-100_install_e.book 24 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Audio Options dialog—Drivers tab Friendly Names For each driver, you can change the driver names that are displayed in SONAR. If you want to use this function, enter the desired name in the Friendly Names field, and select the “Use Friendly Names to Represent Audio Drivers” check box located at the bottom of the dialog box.
VS-100_install_e.book 25 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings MIDI Devices Settings Here’s how to specify the MIDI devices that you want to use. 1. Execute the “Options | MIDI Devices” command to open the “MIDI Devices” dialog box. In the input field and output field of the “MIDI Devices” dialog box, select the following MIDI devices that you will use with SONAR.
VS-100_install_e.book 26 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Caution regarding MIDI Devices When using the SONAR V-STUDIO 100 with a ReWire client such as Project5 Set your MIDI keyboard or other MIDI input device so that it will be used by either SONAR or the ReWire client (not both). If you attempt to use the MIDI input device simultaneously by both, the following problems will occur.
VS-100_install_e.book 27 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings MIDI Controllers/Surfaces Settings Before you use the SONAR V-STUDIO 100 hardware to control SONAR, load the VS-100 plug-in and configure settings to enable it. Loading the VS-100 Plug-in 1. Make sure that the SONAR V-STUDIO 100 hardware is connected to your computer, and then start up SONAR. 2. In SONAR, choose “Options | Controllers/Surfaces” to open the “Controllers/Surfaces” dialog box. 3.
VS-100_install_e.book 28 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings VST/VSTi Registration and Settings By default, the VST plug-ins included with SONAR are installed in the following folder, and can be used from SONAR without changing any settings. C:\Program Files\Cakewalk\VstPlugins If you have VST plug-ins installed in any other folders, you’ll need to register them in SONAR as follows. 1. Execute the “Options | Global” command and click the “VST Plug-Ins” tab. 2.
VS-100_install_e.book 29 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Playing a Demo Song Playing an Audio Demo Song SONAR VS contains audio demo songs. Here’s how to enjoy these demo songs. The demo songs included with SONAR are created at a sampling rate of 44.1 kHz. To play them, both the SONAR V-STUDIO 100 hardware’s sampling frequency and the SONAR Audio Driver must be set to the 44.1 kHz setting. If the audio driver’s sampling rate has been set otherwise, change the rate to 44.
VS-100_install_e.book 30 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings If you don’t hear sound If you don’t hear sound, check the settings of the audio interface and your sound reinforcement equipment. If you don’t hear sound and the audio track’s level meters are not moving either, there may be a problem with the settings of the audio driver. Check the settings as described in “Audio Driver Settings” (p. 21). If the CPU meter indicates a high value fig.meterCPU.
VS-100_install_e.book 31 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings If the DISK meter indicates a high value fig.meterDISK.eps The DISK meter is located on the Status bar, which is at the bottom of the screen. If the DISK meter is staying in the green area, there is probably no problem. If the meter is reaching the yellow area but you don’t hear noise or dropouts (interruptions in the playback), this means that your computer’s capabilities are being used nearly to their limit.
VS-100_install_e.book 32 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Recording audio 1. Connect your instrument or microphone In order to record audio, you’ll connect your instrument or microphone to the SONAR V-STUDIO 100. Some typical types of connections are shown below. Connecting a microphone If you’re using a condenser microphone that has a balanced (XLR) plug and requires phantom power to be supplied, set the PHANTOM switch to “+48V.
VS-100_install_e.book 33 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings Connecting a guitar or bass Connect your electric guitar or electric bass to the INPUT 1L LINE jack, and turn on the Hi-Z button. Guitar, Bass If you’ve connected a guitar/bass, set [Hi-Z] button to ON. Hi-Z Connecting a digital device If you want to make a digital audio connection from a digital mixer or similar device, connect its output (e.g. the DIGITAL OUT connector) to the SONAR V-STUDIO 100’s COAXIAL IN (7/8) jack.
VS-100_install_e.book 34 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 2. Create a new file 1. Launch SONAR. 2. From the File menu, choose New to open the New Project File dialog box. 3. In the Name field of the New Project File dialog box, enter the name of the song that you want to create. fig.FileNew.eps 4. From the templates, choose 16 track audio and click “OK”. 5. A project containing 16 audio tracks will be created. In this example we’re going to record on track 1.
VS-100_install_e.book 35 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 3. Select the input for the track Now we’ll configure input settings in SONAR as appropriate for the input you connected. 1. Press the SONAR V-STUDIO 100’s [SHIFT]+[VIEW] button, or click SONAR’s Console View icon, to open the console view. fig.ConsoleViewIcon01.eps 2. Click the input field for track 1. fig.Input.eps 3. Select the appropriate device for the input you connected.
VS-100_install_e.book 36 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 4. Adjust the level If you’re recording from a device connected to INPUT 1L or INPUT 2R, adjust the levels as follows. In order to record with the best possible audio quality, adjust the input level so that SONAR V-STUDIO 100’s level meter does not light even during the loudest passages. 1. Press SONAR V-STUDIO 100’s [DISPLAY] button. The level meter appears in the display.
VS-100_install_e.book 37 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 5. Arm the desired track for recording. We’ll arm track 1 for recording (i.e. put it in record-ready mode). 1. Press the SONAR V-STUDIO 100’s [DISPLAY] button to switch to the control surface screen. If a different screen is shown, press the [DISPLAY] button once again. 2. Make sure that Track1 is shown in the control surface screen.
VS-100_install_e.book 38 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 6. Turn on the metronome. 1. Choose the SONAR menu item Option|Project, and click the Metronome tab. 2. Select the “Use Audio Metronome” check box. 3. In the Output field, select “VS-100 OUT 1-2” as the metronome’s output port. 4. Click “OK.” fig.metro01.eps 5. In SONAR’s toolbar, double-click the tempo display and enter the desired tempo. Enter a numerical value from your computer keyboard, and press the Enter key to confirm it. fig.
VS-100_install_e.book 39 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 7. Record your performance. Press the record button to start recording. Press the stop button to stop recording. Press the play button to hear the recorded result. If you’re not satisfied with your performance, you can easily re-record it. After you’ve stopped recording but before you’ve performed any other operation, hold down the “Ctrl” key of your computer keyboard and press “Z.
VS-100_install_e.book 40 ページ ２００９年３月１２日 木曜日 午後６時３分 Initial Settings 8. Try out a plug-in effect. SONAR provides a wide variety of plug-in effects. In this example, we’ll apply a plug-in effect to the track you recorded. 1. Right-click the FX bin for track 1. fig.FXbin.eps 2. In the menu that appears, choose “Audio Fx |VX64_VocalStrip.” VocalStrip will be inserted into track 1, and the VocalStrip property page appears. fig.VX64.eps 3. Play back.
VS-100_install_e.book 41 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting 1. This chapter lists problems that might occur when setting up this product, and explains how to solve these problems. If you experience a problem during installation, read this chapter first. 2. If the system still does not operate as you expect even though you’ve checked the points listed in this chapter, refer to the following documents as well.
VS-100_install_e.book 42 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problems When Installing Driver or Changing Settings Problem Installer won’t start up A warning or error is displayed during installation Can’t install the driver according to the procedure 42 Points to check Action Is the CD-ROM correctly inserted in the CD-ROM drive? Make sure that the CD-ROM is correctly inserted in the drive.
VS-100_install_e.book 43 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problem Points to check Action It may take between several tens of seconds and several minutes after you power-on the SONAR V-STUDIO 100 until it is recognized by your computer. This is not a malfunction. Please wait until the Found New Hardware Wizard appears. Is the SONAR V-STUDIO 100 connected? Once again, make sure that the SONAR V-STUDIO 100 is correctly connected to your computer and that the power is on.
VS-100_install_e.book 44 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problem Points to check Action Plug-ins are not installed The plug-ins are not installed (registered) in the Start menu. The software synthesizers included with SONAR are all plug-in versions. Unlike the stand-alone versions, they will not be registered in the Windows Start menu. In order to use the plug-in software synthesizers included with SONAR, you must call them up from within SONAR.
VS-100_install_e.book 45 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problem An error such as “Unknown Error in Sequencer.DLL” appears Points to check Action SONAR was not installed correctly. Proceed as follows to re-install SONAR. 1. Log on as a user who has administrative privileges. 2. Click the Windows Start button, and then click Control Panel. 3. Click Programs and Features (in Windows XP, Add or Remove Programs) 4. In the list of programs, click SONAR VS. 5.
VS-100_install_e.book 46 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problem Points to check Action If Media Player or another application that has audio playback capability is running, SONAR won’t be able to use the audio driver, and an error appears when SONAR is started. Close the audio playback application, and then start SONAR again. No sound at all Could a message be indicating “Unable to Open Audio Playback Device”? Make sure that SONAR’s “About Sampling Rates” (p.
VS-100_install_e.book 47 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problems with Recording Problem Points to check Action If Media Player or another application that has audio playback capability is running, SONAR won’t be able to use the audio driver, and an error appears when SONAR is started. Close the audio playback application, and then start SONAR again. Can’t record Could a message be indicating “Unable to open audio record device”? Make sure that SONAR’s Sampling Rate (p.
VS-100_install_e.book 48 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Problem Sound From the Device Connected to the Input Jacks is Not Loud Enough Noise or distortion occurs Can’t Record via a Digital Connection Points to check Action Are the [MAIN MIX] knob, the level knobs for each input, and the headphone volume knob raised appropriately? Turn these knobs toward the right to adjust the volume.
VS-100_install_e.book 49 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting Eliminating Clicks and Dropouts If data cannot be recorded while recording audio, or if data cannot be fully processed during playback, SONAR will automatically halt. This is called a dropout. Clicks or pops may also occur if problems occur in communication between SONAR and the SONAR V-STUDIO 100 hardware. There are a variety of possible reasons why clicks, pops, and dropouts might occur.
VS-100_install_e.book 50 ページ ２００９年３月１２日 木曜日 午後６時３分 Troubleshooting If problems occur more frequently with large (heavy) projects Increase the Mixing Latency Extremely short Mixing Latency settings may place an excessive load on your computer. “About Mixing Latency” (p. 57) Use freezing or bouncing to reduce the load on your computer If the size of the project exceeds the processing capability of your computer, you can reduce the processing load by freezing synthesizers or bouncing audio tracks.
VS-100_install_e.book 51 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix VS-100 Driver settings Windows Users Changing or Viewing the Settings 1. When changing driver settings, always make sure to first quit all applications using the SONAR V-STUDIO 100 hardware. This is unnecessary when only checking the settings. 2. Open the “Control Panel,” and double-click “VS-100.” * If the above icon cannot be found, click the “Switch to Classic View.” 3. The “VS-100 Driver Settings” dialog box appears. 4.
VS-100_install_e.book 52 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix Macintosh Users Changing or Viewing the Settings 1. Use a USB cable to connect the SONAR V-STUDIO 100 hardware with your computer. 2. Turn the POWER switch of the SONAR V-STUDIO 100 hardware to the “ON” position. 3. Open “System Preferences” and click “VS-100.” The Driver Settings Panel is displayed. Controls in the Settings Dialog Box Audio Buffer Size This changes the Buffer Size for Audio Input/Output of the driver.
VS-100_install_e.book 53 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix Uninstalling VS-100 Driver Windows Vista Users 1. Start up Windows with all USB cables disconnected (except those for a USB keyboard and/or USB mouse, if used). 2. Close all applications before performing the uninstallation. 3. Open “Control Panel” and click “Uninstall a program.” * If you’re using the Classic View, double-click the “Programs and Features” icon. 4. In the list, choose VS-100 Driver, and click “Uninstall/Change.” 5.
VS-100_install_e.book 54 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix Macintosh Users 1. Start computer with all USB cables disconnected. (except the keyboard and mouse) 2. Double-click “VS100_Uninstaller.” 3. The display will indicate “This uninstalls VS-100 driver from this Macintosh.”; click [Uninstall]. * If any other message appears, proceed as directed by that message. 4. The display will indicate “Are you sure to uninstall the driver?”; click [OK]. 5.
VS-100_install_e.book 55 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix Giving Priority to Background Service (Windows XP) On Windows XP, if you omit making this setting, you may experience sound dropout. By making this setting you may be able to solve such problems. Be sure to make this setting before you begin using the SONAR V-STUDIO 100 hardware. 1. Open the “Control Panel,” and double-click “System.” * If you don’t see the above icon, click “Performance and Maintenance,” and then click “System.” 2.
VS-100_install_e.book 56 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix About Sampling Rates The SONAR V-STUDIO 100 hardware allows you to choose from the following sampling rates: 44,100 Hz, 48,000 Hz, and 96,000 Hz. * SONAR does not allow you to change the sampling rate of a project that contains audio data. * Selecting a higher sampling rate will allow you to handle audio at a higher quality, but will require greater performance from your CPU, memory, and hard disk.
VS-100_install_e.book 57 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix About Mixing Latency If the driver mode is set to ASIO, you won’t be able to adjust the Mixing Latency from SONAR. Adjust the “Audio Buffer Size” from the [ASIO Panel]. The Mixing Latency setting is closely related to how SONAR can take full advantage of your computer’s performance. Increasing the mixing latency will allow more audio processing to be performed within SONAR.
VS-100_install_e.book 58 ページ ２００９年３月１２日 木曜日 午後６時３分 Appendix Multi-user Use In order to install SONAR, you must log on as a user who has administrative privileges. Once installed, SONAR can be used by any user (in Windows Vista) or a limited user (in Windows XP), as well as by a user who has administrative privileges. Uninstalling SONAR and Other Components If you want to uninstall a component of SONAR or VS Production Pack, use the following procedure to uninstall that component. 1.
VS-100_install_e.
VS-100_install_e.
VS-100_install_e.
VS-100_install_e.
VS-100_install_e.
VS-100_install_e.
