User Manual
Table Of Contents
- USING THE UNIT SAFELY
- IMPORTANT NOTES
- Contents
- Overview
- Setup
- Performance
- Drum Kit
- Instrument
- Mixer
- Effects
- Tempo
- Song Player
- Pattern Sequencer
- Settings
- Backing Up the Settings
- Data saved in USB flash drive
- Backing Up All Data to a USB Flash Drive (SAVE)
- Loading Backup Data from a USB Flash Drive (LOAD)
- Importing Kit Data from TD-20/TD-20X Backup Data (IMPORT)
- Deleting Backup Data from a USB Flash Drive (DELETE)
- Backing Up a Drum Kit to a USB Flash Drive (KITSAVE)
- Loading Kit Data from a USB Flash Drive (KITLOAD)
- Checking the State of a USB Flash Drive (INFO)
- Formatting a USB Flash Drive (FORMAT)
- Overall Settings for the TD-30 (SETUP)
- Output Assignments (OUTPUT)
- Assigning a Function to a Footswitch or Pad (CONTROL)
- Other Settings (OPTION)
- Restoring the Factory Settings (F RESET)
- Playing a Kit from the USB Flash Drive Without Loading It (Kit Selection) (KIT SEL)
- Digital Audio Level (GAIN)
- Auto Off Function (AUTOOFF)
- Viewing the Remaining Memory and the Program Version (INFO)
- Trigger Settings
- Backing Up the Settings
- Expansion
- Appendices
Eects
75
LONG REVERB
This is a very rich sounding reverb with a choice of
Character.
Parameter Value Explanation
Reverb Time 0–127
Time length of reverbera-
tion
Character 0–5 Type of reverb
PreLPF
16–15000 Hz,
BYPASS
Frequency of the lter that
cuts the high-frequency
content of the input
sound (BYPASS: no cut)
PreHPF
BYPASS,
16–15000 Hz
Frequency of the lter that
cuts the low-frequency
content of the input
sound (BYPASS: no cut)
Pre EQ Freq 200–8000 Hz
Frequency of the lter
that boosts/cuts a specic
frequency region of the
input sound
Pre EQ Gain -15–+15 dB
Amount of boost/cut
produced by the lter at
the specied frequency
region of the input sound
Depth 0–127 Depth of the eect
HFDamp
16–15000 Hz,
BYPASS
Frequency at which the
high-frequency content of
the resonant sound will be
cut (BYPASS: no cut)
LFDamp
BYPASS,
16–15000 Hz
Frequency at which the
low-frequency content of
the resonant sound will be
cut (BYPASS: no cut)
EQ Lo -15–+15 dB
Amount of low-range
boost/cut
EQ Hi -15–+15 dB
Amount of high-range
boost/cut
SATURATOR
A saturator which distorts the sound is connected in
parallel with a compressor, producing a rougher tonal
character and boosting the loudness. This also cuts the
low-frequency region of the input audio.
Parameter Value Explanation
Saturator
Gain
0–127
Input volume to the
saturator
Saturator
Drive
0–127 Amount of distortion
Saturator
Level
0–127
Output volume of the
saturator
Comp Depth 0–127 Amount of compression
Comp Level 0–127
Output volume of the
compressor
EQ Higain -12–+6 dB
Amount of high-range
boost/cut
SUPER FILTER
This is a lter with an extremely sharp slope. The cuto
frequency can be varied cyclically.
Parameter Value Explanation
Type
LPF, BPF, HPF,
NOTCH
Filter type
Frequency range that will
pass through each lter
LPF: Frequencies below
the cuto
BPF: Frequencies in the
region of the cuto
HPF: Frequencies above
the cuto
NOTCH: Frequencies other
than the region of the
cuto
Cuto 0–127
Cuto frequency of the
lter
Increasing this value will
raise the cuto frequency.
Resonance 0–127
Filter resonance level
Increasing this value will
emphasize the region
near the cuto frequency
Modulation
Switch
OFF, ON
On/o switch for cyclic
change
Rate 0–127 Rate of modulation
Depth 0–127 Depth of modulation
FILTER+DRIVE
This is a low-pass lter equipped with overdrive. It cuts
the upper range and adds distortion.
Parameter Value Explanation
Cuto 0–127
Cuto frequency of the
lter
Increasing this
value will raise the cuto
frequency.
Resonance 0–127
Filter resonance level
Increasing this value will
emphasize the region
near the cuto frequency
Drive 0–127 Amount of distortion
AppendicesExpansionSettingsPerformanceSetupOverview