User Manual
Table Of Contents
- USING THE UNIT SAFELY
- IMPORTANT NOTES
- Contents
- Overview
- Setup
- Performance
- Drum Kit
- Instrument
- Mixer
- Effects
- Tempo
- Song Player
- Pattern Sequencer
- Settings
- Backing Up the Settings
- Data saved in USB flash drive
- Backing Up All Data to a USB Flash Drive (SAVE)
- Loading Backup Data from a USB Flash Drive (LOAD)
- Importing Kit Data from TD-20/TD-20X Backup Data (IMPORT)
- Deleting Backup Data from a USB Flash Drive (DELETE)
- Backing Up a Drum Kit to a USB Flash Drive (KITSAVE)
- Loading Kit Data from a USB Flash Drive (KITLOAD)
- Checking the State of a USB Flash Drive (INFO)
- Formatting a USB Flash Drive (FORMAT)
- Overall Settings for the TD-30 (SETUP)
- Output Assignments (OUTPUT)
- Assigning a Function to a Footswitch or Pad (CONTROL)
- Other Settings (OPTION)
- Restoring the Factory Settings (F RESET)
- Playing a Kit from the USB Flash Drive Without Loading It (Kit Selection) (KIT SEL)
- Digital Audio Level (GAIN)
- Auto Off Function (AUTOOFF)
- Viewing the Remaining Memory and the Program Version (INFO)
- Trigger Settings
- Backing Up the Settings
- Expansion
- Appendices
Eects
77
RING MODULATOR
This is an eect that applies amplitude modulation (AM)
to the input signal, producing bell-like sounds. You can
also change the modulation frequency in response to
changes in the volume of the sound sent into the eect.
Parameter Value Explanation
Mode
RING MOD,
ENV OSC
RING MOD: Applies
amplitude modulation to
the input signal
ENV OSC: Outputs
oscillation corresponding
to the input signal
Frequency 0–127
Adjusts the frequency
at which modulation is
applied.
Sensitivity 0–127
Adjusts the amount of
frequency modulation
applied.
Polarity UP, DOWN
Determines whether the
frequency modulation
moves towards higher
frequencies (UP) or lower
frequencies (DOWN).
STEP RINGMOD
This is a ring modulator that uses a 8-step sequence to
vary the frequency at which modulation is applied.
Parameter Value Explanation
Mode
RING MOD,
ENV OSC
RING MOD: Applies
amplitude modulation to
the input signal
ENV OSC: Outputs
oscillation corresponding
to the input signal
Freq Modify -64–63
Increases/decreases value
for all steps
Freq Step 1–8 0–127
Frequency of ring modula-
tion at each step
Attack 0–127
Speed at which the
modulation frequency
changes between steps
Rate 0–127
Rate at which 8-step
sequence is to be
repeated
PITCH SHIFT
Shifts the pitch of the original sound. This pitch shift can
add two pitch shifted sounds to the original sound.
Parameter Value Explanation
Pitch1 (semi) -24–+12 semi
Adjusts the pitch of Pitch
Shift 1 in semitone steps.
Pitch2 (semi) -24–+12 semi
Adjusts the pitch of Pitch
Shift 2 in semitone steps.
DlyTime 0–1300 msec
Adjusts the delay time
from the direct sound
until the Pitch Shift sound
is heard.
Feedback -98–+98 %
Adjusts the proportion of
the pitch shifted sound
that is fed back into the
eect.
Negative (-) settings will
invert the phase.
Pitch1 Level 0–127
Volume of the Pitch Shift
1 sound
Pitch2 Level 0–127
Volume of the Pitch Shift
2 sound
Wet Gain Low -15–+15 dB
Amount of boost/cut for
the eect sound’s lower
range
Wet Gain High -15–+15 dB
Amount of boost/cut for
the eect sound’s upper
range
AUTO PAN
Cyclically modulates the stereo location of the sound.
Parameter Value Explanation
Rate 0–127 Frequency of the change
Depth 0–127
Depth to which the eect
is applied
AppendicesExpansionSettingsPerformanceSetupOverview