Owners Manual
Table Of Contents
- USING THE UNIT SAFELY
- IMPORTANT NOTES
- Panel Descriptions
- Basic Operations
- Video Input/Output Settings
- Video Operations
- Video Composition Operations
- Audio Operations
- Adjusting the Volume Level
- Outputting AUX-bus Audio
- Applying Effects to Audio
- Controlling Volume Levels Automatically (Auto Mixing)
- Muting Out Specific Input Audio (Mute)
- Interlinking Audio Output to Video Switching (Audio Follow)
- Separating Discrete Analog Input Audio Streams and Adding Them to SDI Video
- Other Features
- Saving/Recalling Settings (Preset Memory)
- Saving the Unit’s Settings on a USB Flash Drive
- Formatting USB Flash Drives
- Returning Settings to the Factory-default State (Factory Reset)
- Preventing Unintended Operation (Panel Lock)
- Operating the V-60HD by Remote Control
- Outputting a Tally Signal
- Using Smart Tally
- Appendices
9
Panel Descriptions
AUDIO IN 5/6 jacks
These jacks input audio
signals from video decks, CD
players, and other such audio
equipment.
AUDIO IN 1–4 jacks (XLR/TRS)
These jacks input audio signals from
microphones, audio mixers, and other
such audio equipment.
PHONES jack
Connect headphones
to this jack.
Stereo 1/4-inch
phone plug
Pin assignment of AUDIO IN 1–4 jacks (XLR/TRS)
1: GND
2: HOT
TIP: HOT
RING: COLD
SLEEVE: GND
3: COLD
2: HOT
1: GND
3: COLD
Pin assignment of AUDIO OUT connectors (XLR)
1: GND
2: HOT
TIP: HOT
RING: COLD
SLEEVE: GND
3: COLD
2: HOT
1: GND
3: COLD
AUDIO OUT connectors/jacks (XLR and RCA)
These output the results of audio mixing (master out). Connect them to an audio
recording deck, amplier, speakers, or other such equipment.
Using Phantom Power
You can supply phantom power (+48 V) from the AUDIO IN 1 through
4 jacks. Turn on phantom power when you’re using a condenser
microphone that requires phantom power.
Select the [MENU] button
0
“AUDIO INPUT”
0
“AUDIO IN 1” through
“AUDIO IN 4”
0
set “PHANTOM +48V” to “ON.”
NOTE
Always turn the phantom power o when connecting any device
other than condenser microphones that require phantom power.
You risk causing damage if you mistakenly supply phantom power
to dynamic microphones, audio playback devices, or other devices
that don’t require such power. Be sure to check the specications of
any microphone you intend to use by referring to the manual that
came with it.
(This instrument’s phantom power: 48 V DC, 14 mA Max)
Front Panel
Grounding terminal
Connect this to an external earth or
ground.
* Connect this if necessary.
TALLY/GPI connector
Connect devices provided with a tally-
light feature or with control-signal output
functionality to this connector.
[PHONES] knob
This adjusts the volume level for
headphones.
USB MEMORY port
Connect a USB ash drive to this port. You use it when
importing still images (p. 19) or when saving or loading
settings for the unit (p. 32).
* When using a USB ash drive for the rst time, you
must format it using the V-60HD.
* Never turn o the power or remove the USB ash drive while
the USB ash drive is being accessed.
Audio input connectors Audio output connectors
1/4-inch TRS
phone plugXLR plug
* You can also output just AUX-bus audio
from the AUDIO OUT connectors and jacks
(XLR and RCA) and the PHONES jack (p. 25).
Audio output connectors
RCA
phono plug
RCA
phono plug XLR plug