* Hi-hat stand is not included. For details on compatible stands, refer to p. 10.
USING THE UNIT SAFELY About WARNING and CAUTION Notices About the Symbols The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
IMPORTANT NOTES Placement Additional Precautions • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. • Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.
Getting Started Features Similar Touch and Feel as with an Acoustic Hi-Hat Package Contents Top Hi-Hat The superior design has taken into account not only the shape of the hi-hat, but also the bounce of the stick, and even the movement caused by playing, making it possible to play with the same feel as an acoustic hi-hat.
Mounting on the Hi-Hat Stand * Orient the stopper so that it matches the groove in the top hi-hat. (1) Assembling the Top Hi-Hat * Due to the different shape, the clutch included with the hi-hat stand cannot be used with the VH-13. Be sure to use the special VH-13 clutch. Bottom of the top hi-hat Clutch Top Clutch Screw Lock Nuts Felt Washer Stopper 1. Stopper Clutch Bolt Plate Use the drum key included with the VH-13 to loosen the clutch bolt, then simultaneously turn and remove the clutch top.
Mounting on the Hi-Hat Stand At this point, position the LINK jack so it’s on the far side of the unit, facing away from the performer. (2) Assembling the Bottom Hi-Hat 1. Remove the clutch included with the hi-hat stand from the cymbal rod. LINK jack * The clutch included with the hi-hat stand will not be used. * It is not necessary to remove the felt (or rubber) pad on the hi-hat stand used for supporting the bottom cymbal. 2. Confirm that the cymbal rod is firmly secured.
Mounting on the Hi-Hat Stand 6. Attach the clamp and holder to the pipe on the upper part of the hi-hat stand, then slightly tighten the assembly with the drum key. (3) Assembling the Overall Unit 1. Place the top hi-hat assembly on the hi-hat stand with the cymbal rod passing through the top hi-hat hole. At this point, position the “Roland” logo on the farther side, as viewed from the performer. Slightly tighten 7. 2. Use the link cable to connect the bottom hi-hat and the top hi-hat LINK jacks. 3.
Mounting on the Hi-Hat Stand (4) Connecting to a Sound Module (5) Adjusting the Sound Module When using the VH-13, you will need to make the settings for the sound module. * To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections. 1. Connect the VH-13’s TRIGGER OUTPUT jack to the sound module’s TRIGGER INPUT HI-HAT jack, and the VH-13’s CONTROL OUTPUT jack to the sound module’s HH CTRL jack. When Using with the TD-30 1. 2.
Mounting on the Hi-Hat Stand When Not Playing (6) Adjusting the Hi-Hat 1. Adjust the gap between the top hi-hat and bottom hi-hat to a clearance of approximately 10 mm, then tighten the clutch screw. When you’re not playing, secure the top hi-hat cymbal and bottom hi-hat cymbal so that they are separated by at least 10 mm of space. Malfunction may occur if they are not separated.
Playing Methods Open/Closed The hi-hat tone changes smoothly and continuously from open to closed in response to how far the pedal is pressed. You can also play the foot closed sound (playing the hi-hat with the pedal completely pressed down) and foot splash sound (playing the hi-hat with the pedal fully pressed and then instantly opening it). Edge Shot This playing method involves striking the edge of the top hi-hat with the shoulder of the stick.
Troubleshooting Problem Confirmation Hi-hat not closing Was the unit adjusted after When using the VH-13, be sure to run the automatic offset adjustment on your sound module being connected to the (p. 8).
For EU Countries For China WARNING For C.A. US (Proposition 65) This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
Information AFRICA EGYPT Al Fanny Trading Office 9, EBN Hagar Al Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: (022)-417-1828 REUNION MARCEL FO-YAM Sarl 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SOUTH AFRICA T.O.M.S. Sound & Music (Pty)Ltd. 2 ASTRON ROAD DENVER JOHANNESBURG ZA 2195, SOUTH AFRICA TEL: (011) 417 3400 Paul Bothner(PTY)Ltd.
