VS-700R_e1.book 1 ページ 2010年6月15日 火曜日 午後4時59分 Owner‘s Manual Read this First This manual provides instructions on how to use the VS-700R I/O on its own and how to add on a second VS-700R I/O. For instructions on how to perform the installation, make the necessary settings, and operate the unit, please refer to the “VS-700 Getting Started” and the “VS-700 Owner’s Manual.
VS-700R_e1.book 2 ページ 2010年6月15日 火曜日 午後4時59分 WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
VS-700R_e1.book 3 ページ 2010年6月15日 火曜日 午後4時59分 USING THE UNIT SAFELY The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
VS-700R_e1.book 4 ページ 2010年6月15日 火曜日 午後4時59分 USING THE UNIT SAFELY 015 • 101a Do not force the unit’s power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cords—the total power used by all devices you have connected to the extension cord’s outlet must never exceed the power rating (watts/amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through. ................
VS-700R_e1.book 5 ページ 2010年6月15日 火曜日 午後4時59分 USING THE UNIT SAFELY 120 • Always turn the phantom power off when connecting any device other than condenser microphones that require phantom power. You risk causing damage if you mistakenly supply phantom power to dynamic microphones, audio playback devices, or other devices that don’t require such power. Be sure to check the specifications of any microphone you intend to use by referring to the manual that came with it.
VS-700R_e1.book 6 ページ 2010年6月15日 火曜日 午後4時59分 IMPORTANT NOTES Power Supply Maintenance 301 401a • Do not connect this unit to the same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise.
VS-700R_e1.book 7 ページ 2010年6月15日 火曜日 午後4時59分 IMPORTANT NOTES 853 • Do not use this unit for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this unit. 204 * Microsoft and Windows and Windows Vista are registered trademarks of Microsoft Corporation. 206j ® ® ® * Windows is known officially as: “Microsoft Windows operating system.
VS-700R_e1.book 8 ページ 2010年6月15日 火曜日 午後4時59分 Contents USING THE UNIT SAFELY............................................................................................................3 IMPORTANT NOTES .....................................................................................................................6 Checking the Contents of the Package ................................................................................9 Using the VS-700R I/O in Standalone Mode .............................
VS-700R_e1.book 9 ページ 2010年6月15日 火曜日 午後4時59分 Checking the Contents of the Package As soon as you open the package, check that you have all of the included items. If anything is missing, contact your dealer. * This package does not include the following items that are listed in “Checking the Contents of the Package” (p. 6) of “VS-700 Getting Started.
VS-700R_e1.book 10 ページ 2010年6月15日 火曜日 午後4時59分 Checking the Contents of the Package USB Cable Use this cable to connect the VS-700R I/O unit to your computer’s USB connector. * Please use the included USB cable.
VS-700R_e1.book 11 ページ 2010年6月15日 火曜日 午後4時59分 Using the VS-700R I/O in Standalone Mode To use the VS-700R I/O without connecting it to the VS-700C console, it needs to be set to “Standalone mode.” While in Standalone mode, AUX IN cannot be used. Changes to the Settings In order to use the VS-700R I/O in “Standalone mode,” you need to open the top cover (ARX slot), then set the SETTING dip switches to the positions shown below. Next, switch the unit's power off, then turn it back on again.
VS-700R_e1.book 12 ページ 2010年6月15日 火曜日 午後4時59分 Connecting Two VS-700R I/O Units The Advantages of Connecting VS-700R I/O Units By connecting two VS-700R I/O units, you'll be able to take advantage of the audio input/output of the two units, have access to two synthesizers (Fantom VS), and be able to use two ARX expansion boards. You will need a faster system if you connect two VS-700R I/O units.
VS-700R_e1.book 13 ページ 2010年6月15日 火曜日 午後4時59分 Connecting Two VS-700R I/O Units 3. Connect the WORDCLOCK. Use a BNC cable to connect the WORDCLOCK OUT connector of the first unit to the WORDCLOCK IN connector of the second unit. Set the audio clock source of the second unit to “Wordclock” (p. 20). Now the audio clock of the second unit will be synchronized. * A BNC cable is not included with this package. 4. Start up SONAR.
VS-700R_e1.book 14 ページ 2010年6月15日 火曜日 午後4時59分 Connecting the Power Cord • Connect the power cord. fig.VS-700-connect04-e.
VS-700R_e1.book 15 ページ 2010年6月15日 火曜日 午後4時59分 Turning the Power On 941 Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 945 If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 6). 1.
VS-700R_e1.book 16 ページ 2010年6月15日 火曜日 午後4時59分 Connecting Recording Equipment Connections to the Analog Jacks fig.VS-700-rec01-mic-e.eps Connecting a Mic The VS-700R provides a balanced (XLR) type connector that is wired as shown in the illustration. Check the wiring of your device before connecting it. VS-700R Rear Panel The eight audio inputs (INPUT 1–8) contain phantom power supplies. From SONAR’s “Tools” menu, open “VS-700” and select the “MIC PRE” tab, and click [+48] button to make settings.
VS-700R_e1.book 17 ページ 2010年6月15日 火曜日 午後4時59分 Connecting Recording Equipment Connections to the Digital Connectors fig.VS-700-rec02-digi-e.eps Connecting a Digital Audio Source If you want to digitally connect a DAT or similar device, connect its output connector (e.g., DIGITAL OUT connector) to the VS-700R's DIGITAL IN connector. VS-700R Rear Panel The DIGITAL 1 coaxial connector and AES/EBU connector are a mutually exclusive selection.
VS-700R_e1.book 18 ページ 2010年6月15日 火曜日 午後4時59分 Switching the Sampling Rate Use the front panel [SAMPLE RATE] knob to select the sampling rate. To make the system reflect the new setting, you’ll need to cycle the power to the system. If you need to synchronize the VS-700 to another digital device, you must first set this knob to the same sampling rate as the master device. 1. Close the software you’re using. 2. Switch off the power to the VS-700R I/O and the VS-700C console. 3.
VS-700R_e1.book 19 ページ 2010年6月15日 火曜日 午後4時59分 Switching the Sampling Rate Setting SONAR’s Sampling Rate * In SONAR, you cannot change the sampling rate of a project that contains audio data. 1. Start up SONAR. 2. If an "Audio Driver Error" is displayed during startup, click [Use Anyway]. 3. Choose “Options|Audio” to display the “Audio Options” dialog box. 4. On the “General” tab of the dialog, select a value in the Sampling Rate dropdown menu, and a value from the Audio Driver Bit Depth dropdown menu.
VS-700R_e1.book 20 ページ 2010年6月15日 火曜日 午後4時59分 Audio Clock Source You can choose one of four types of clock source. The current clock source is shown by the front panel SYNC indicator. In the case of an external source, the indicator will light if synchronization is locked. The indicator will blink if synchronization is not locked If you’re using SONAR, you can select the clock source parameters as described below.
VS-700R_e1.book 21 ページ 2010年6月15日 火曜日 午後4時59分 Installing the ARX Expansion Board Up to one optional Expansion Board (ARX series; sold separately) can be installed in the VS-700R. For details on ARX expansion boards, refer to the owner’s manual of your ARX expansion board. For details on the ARX expansion editor (plug-in), refer to the online manual for the editor (plug-in). Port settings (MIDI input and audio output) The ARX expansion board’s ports have the following names.
VS-700R_e1.book 22 ページ 2010年6月15日 火曜日 午後4時59分 Installing the ARX Expansion Board How to Install an Expansion Board Install the Expansion Board after removing the panel cover. 1. Before installing the Expansion Board, turn off the power of the VS-700R and all connected devices, and disconnect all cables, including the Power cable, from the VS-700R. 2. From the VS-700R, remove only the screws shown in the following diagram, and detach the cover. VS-700R Top Panel fig.exp02.eps 3.
VS-700R_e1.book 23 ページ 2010年6月15日 火曜日 午後4時59分 Installing the ARX Expansion Board 4. Insert the board into the VS-700R’s non-latched board holders until you hear a click. fig.attach02.eps Board Connector of board Align board’s holes with holders Connector of the VS-700R Non-latched holders 5. Gently lower the board into place. fig.attach04.eps 6. From above, press down on the board at the three locations indicated in the illustration until the latched board holders lock into place. fig.attach06.
VS-700R_e1.book 24 ページ 2010年6月15日 火曜日 午後4時59分 Installing the ARX Expansion Board Removing an Expansion Board To remove an expansion board, reverse the process by which you inserted it. 1. Unlatch the latched board holders. fig.attach08.eps 2. Verify that the two latched board holders are unlocked, then gently pull up the board and disconnect the connector. fig.attach09.eps 3. Disengage the board from the non-latched board holders, and remove the board. 4.
VS-700R_e1.book 25 ページ 2010年6月15日 火曜日 午後4時59分 Installation de la carte d’expansion (French Language for Canadian Safety Standard) Un maximum de un carte d’expansion optionnelles (serie ARX; vendues separement) peuvent etre installees dans le VS-700R. Precautions a prendre lors de l’installation d’une carte d’expansion • Veuillez suivre attentivement les instructions suivantes quand vous manipulez la carte afin d’eviter tout risque d’endommagement des pieces internes par l’electricite statique.
VS-700R_e1.book 26 ページ 2010年6月15日 火曜日 午後4時59分 Installation de la carte d’expansion Installation d’une carte d’expansion Retirer le panneau inferieur avant d’installer les cartes d’expansion. 1. Avant d’installer la carte d’expansion Wave, coupez l’alimentation du VS-700R et de tous les appareils branches, et debranchez tous les cables du VS-700R, y compris le cable d’alimentation. 2. Sur les modeles VS-700R, retirer uniquement les vis illustrees dans le schema ci-dessous et retirer le couvercle. fig.
VS-700R_e1.book 27 ページ 2010年6月15日 火曜日 午後4時59分 Installation de la carte d’expansion 4. Inserer la carte dans les supports non bloques jusqu’a ce qu’un clic se fasse entendre. fig.attach02f.eps Carte Connecteur de la carte Aligner les trous de la carte et les supports Connecteur de le VS-700R Supports non bloqués 5. Abaisser la carte delicatement. fig.attach04.eps 6. Appuyer sur la carte aux trois points indiques sur l’illustration jusqu’a ce que les supports se bloquent en place. fig.attach06f.
VS-700R_e1.book 28 ページ 2010年6月15日 火曜日 午後4時59分 Installation de la carte d’expansion Retrait d’une carte d’expansion Pour retirer une carte d’expansion, suivre le processus inverse du processus d’insertion. 1. Suivre les instructions donnees dans le guide d’utilisation de le VS-700R pour degager la fente ou la carte d’expansion a ete installee. fig.attach08.eps 2. Debloquer les supports de carte. fig.attach09.eps 3.
VS-700R_e1.book 29 ページ 2010年6月15日 火曜日 午後4時59分 Attaching the Rackmount Brackets If you want to install the VS-700R I/O in a 19” rack, attach the included rackmount brackets. 1. Disconnect all connection cables from the VS-700R, including the power cord. 2. As shown in the illustration below, remove three screws each from the left and right sides of the VS-700R. fig.rack01.eps 3. Attach the rackmount brackets using the screws you removed in step 2. fig.rack02.eps 4.
VS-700R_e1.
VS-700R_e1.book 31 ページ 2010年6月15日 火曜日 午後4時59分 For the USA DECLARATION OF CONFORMITY Compliance Information Statement Model Name : Type of Equipment : Responsible Party : Address : Telephone : VS-700R USB Audio Interface Cakewalk, Inc. 268 Summer Street Boston, MA 02210 USA (617) 423-9004 For EU Countries This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.
VS-700R_e1.