Network Camera User Manual UD.
User Manual of Network Camera 1 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual may contain several technical or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual. DISCLAIMER STATEMENT “Underwriters Laboratories Inc.
User Manual of Network Camera 2 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
User Manual of Network Camera 3 Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
User Manual of Network Camera 4 Cautions: Make sure the power supply voltage is correct before using the product. Do not drop the product or subject it to physical shock. Do not install the product on vibratory surface or places. Do not expose it to high electromagnetic radiating environment. Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal damage to the product.
5 User Manual of Network Camera Table of Contents Chapter 1 System Requirement ................................................................................................ 7 Chapter 2 Network Connection ................................................................................................ 8 2.1 Setting the Network Camera over the LAN.............................................................................. 8 2.1.1 Wiring over the LAN ...............................................
User Manual of Network Camera 6 5.5.2 Configuring OSD Settings ................................................................................................... 40 5.5.3 Configuring Text Overlay Settings ...................................................................................... 42 5.5.4 Configuring Privacy Mask .................................................................................................. 42 5.6 Configuring and Handling Alarms ......................................
User Manual of Network Camera 7 Chapter 1 System Requirement Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above versions.
8 User Manual of Network Camera Chapter 2 Network Connection Before you start: If you want to set the network camera via a LAN (Local Area Network), please refer to Section 2.1 Setting the Network Camera over the LAN. If you want to set the network camera via a WAN (Wide Area Network), please refer to Section 2.2 Setting the Network Camera over the WAN. 2.
User Manual of Network Camera 9 Figure 2‐2 Connecting via a Switch or a Router 2.1.2 Detecting and Changing the IP Address You need the IP address to visit the network camera. Steps: 1. To get the IP address, you can install the iVMS‐4200 client software to list the online devices. Please refer to the user manual of iVMS‐4200 client software for detailed information. 2. Change the IP address and subnet mask to the same subnet as that of your computer. 3.
10 User Manual of Network Camera Figure 2‐3 iVMS‐4200 Interface 2.2 Setting the Network Camera over the WAN Purpose: This section explains how to connect the network camera to the WAN with a static IP or a dynamic IP. 2.2.1 Static IP Connection Before you start: Please apply a static IP from an ISP (Internet Service Provider). With the static IP address, you can connect the network camera via a router or connect it to the WAN directly. Connecting the network camera via a router Steps: 1.
User Manual of Network Camera 11 assistance with port mapping. Refer to Appendix 2 for detailed information about port mapping. 5. Visit the network camera through a web browser or the client software over the internet. Figure 2‐4 Accessing the Camera through Router with Static IP Connecting the network camera with static IP directly You can also save the static IP in the camera and directly connect it to the internet without using a router. Refer to Section 2.1.
User Manual of Network Camera 12 7. Visit the camera via the applied domain name. Connecting the network camera via a modem Purpose: This camera supports the PPPoE auto dial‐up function. The camera gets a public IP address by ADSL dial‐up after the camera is connected to a modem. You need to configure the PPPoE parameters of the network camera. Refer to Section 5.3.3 Configuring PPPoE Settings for detailed configuration.
User Manual of Network Camera 13 Figure 2‐8 Private Domain Name Resolution Steps: 1. Install and run the IP Server software in a computer with a static IP. 2. Access the network camera through the LAN with a web browser or the client software. 3. Enable DDNS and select IP Server as the protocol type. Refer to Section 5.3.4 Configuring DDNS Settings for detailed configuration.
14 User Manual of Network Camera Chapter 3 Access to the Network Camera 3.1 Accessing by Web Browsers Steps: 1. Open the web browser. 2. In the address field, input the IP address of the network camera, e.g., 192.0.0.64 and hit the enter key to enter the login interface. 3. Input the user name and password and click . The default user name is admin, password is 12345. Figure 3‐1 Login Interface 4. Install the plug‐in before viewing the live video and operating the camera.
15 User Manual of Network Camera Figure 3‐3 Install Plug‐in (1) Figure 3‐4 Install Plug‐in (2) Figure 3‐5 Install Plug‐in (3) You may have to close the web browser to install the plug‐in. Please reopen the web browser and log in again after installing the plug‐in.
16 User Manual of Network Camera 3.2 Accessing by Client Software 3.2.1 Accessing by iVMS‐4200 Software The product CD contains the iVMS‐4200 client software (Client or PCNVR). You can view the live video and manage the camera with the client software. Follow the installation prompts to install the software. The control panel and live view interface of iVMS‐4200 are shown below.
User Manual of Network Camera 17 Figure 3‐7 iVMS‐4200 Configuration Panel For detailed information about iVMS‐4200 client software, please refer to the user manual of the iVMS‐4200 software. 3.2.2 Accessing by iVMS‐4500 Software To view the camera with a mobile phone, install the iVMS‐4500 client software in your mobile phone. You can find the software in the CD in the package. For detailed information about iVMS‐4500 client software, please refer to the user manual of iVMS‐4500 software.
18 User Manual of Network Camera Chapter 4 Live View 4.1 Live View Page Purpose: The live video page allows you to view live video, capture images, realize PTZ control, set/call presets and configure video parameters. Log in the network camera to enter the live view page, or you can click on the menu bar of the main page to enter the live view page. Descriptions of the live view page: Figure 4‐1 Live View Page Menu Bar: Click each tab to enter Live View, Playback, Log and Configuration page respectively.
19 User Manual of Network Camera Set and call the preset for the camera (if supports PTZ function or an external pan/tilt unit has been installed). Live View Parameters: Configure the image size and stream type of the live video. 4.2 Starting Live View In the live view window as shown in Figure 4‐2, click on the toolbar to start the live view of the camera.
20 User Manual of Network Camera 4.3 Recording and Capturing Pictures Manually In the live view interface, click on the toolbar to capture the live pictures or click to record the live video. The saving paths of the captured pictures and clips can be set on the Configuration > Local Configuration page. To configure remote scheduled recording, please refer to Section 6.2. The captured image will be saved as a JPEG file in your computer. 4.
21 User Manual of Network Camera There are 8 direction arrows ( , when you click and drag the mouse in the relative positions. For the cameras which support lens movements only, the direction buttons are invalid. , , , , , , ) in the live view window Table 4‐2 Descriptions of PTZ Control Panel Button Description Zoom in/out Focus near/far Iris open/close Light on/off Wiper on/off One‐touch focus Initialize lens Adjust speed of pan/tilt movements 4.4.
22 User Manual of Network Camera 4. You can click to delete the preset. You can configure up to 128 presets. Calling a Preset: This feature enables the camera to point to a specified preset scene manually or when an event takes place. For the defined preset, you can call it at any time to the desired preset scene. In the PTZ control panel, select a defined preset from the list and click to call the preset. Figure 4‐5 Calling a Preset 4.
23 User Manual of Network Camera Chapter 5 Network Camera Configuration 5.1 Configuring Local Parameters The local configuration refers to the parameters of the live view, record files and captured pictures. The record files and captured pictures are the ones you record and captured using the web browser and thus the saving paths of them are on the PC running the browser. Steps: 1. Enter the Local Configuration interface: Configuration > Local Configuration Figure 5‐1 Local Configuration Interface 2.
24 User Manual of Network Camera MULTICAST: It’s recommended to select MCAST type when using the Multicast function. For detailed information about Multicast, refer to Section 5.3.1 TCP/IP Settings. Live View Performance: Set the live view performance to Least Delay, Balanced or Best Fluency. Record File Settings: Set the saving path of the recorded video files. Valid for the record files you recorded with the web browser.
25 User Manual of Network Camera Figure 5‐2 Time Settings Select the Time Zone. Select the Time Zone which is the closest to the location of the camera from the drop‐down menu. Synchronizing Time by NTP Server. (1) Check the checkbox to enable the NTP function. (2) Configure the following settings: Server Address: IP address of NTP server. NTP Port: Port of NTP server. Interval: The time interval between the two synchronizing actions with NTP server.
26 User Manual of Network Camera Figure 5‐4 Time Sync Manually Click tab to enable the DST function and Set the date of the DST period. Figure 5‐5 DST Settings 2. Click to save the settings. 5.3 Configuring Network Settings 5.3.1 Configuring TCP/IP Settings Purpose: TCP/IP settings must be properly configured before you operate the camera over network. The camera supports both the IPv4 and IPv6.
27 User Manual of Network Camera Figure 5‐6 TCP/IP Settings 2. Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings and Multicast Address. The valid value range of MTU is 500 ~ 1500. The Multicast sends a stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address.
28 User Manual of Network Camera Configuration > Basic Configuration > Network > Port Or Configuration > Advanced Configuration > Network > Port Figure 5‐7 Port Settings 2. Set the HTTP port, RTSP port and HTTPS port of the camera. HTTP Port: The default port number is 80, and can be changed to any port range 1024 to 65535. RTSP Port: The default port number is 554. HTTPS Port: The default port number is 443, and can be changed to any port range 1024 to 65535.
User Manual of Network Camera 29 The User Name and Password should be assigned by your ISP. 4. Click to save and exit the interface. A reboot is required for the settings to take effect. 5.3.4 Configuring DDNS Settings Purpose: If your camera is set to use PPPoE as its default network connection, you can use the Dynamic DNS (DDNS) for network access. Before you start: Registration on the DDNS server is required before configuring the DDNS settings of the camera. Steps: 1.
30 User Manual of Network Camera Figure 5‐10 DynDNS Settings IP Server: Steps: (1) Enter the Server Address of the IP Server. (2) Click to save the settings. For the IP Server, you have to apply a static IP, subnet mask, gateway and preferred DNS from the ISP. The Server Address should be entered with the static IP address of the computer that runs the IP Server software. Figure 5‐11 IPServer Settings For the US and Canada area, you can enter 173.200.91.74 as the server address.
31 User Manual of Network Camera Figure 5‐12 HiDDNS Settings (2) Enter the Server Address www.hiddns.com. (3) Enter the Domain name of the camera. The domain is the same with the device alias in the HiDDNS server. (4) Click to save the new settings. A reboot is required for the settings to take effect. 5.3.5 Configuring SNMP Settings Purpose: You can set the SNMP function to get camera status, parameters and alarm related information and manage the camera remotely when it is connected to the network.
32 User Manual of Network Camera Figure 5‐13 SNMP Settings 2. Check the corresponding version checkbox ( , , ) to enable the feature. 3. Configure the SNMP settings. The settings of the SNMP software should be the same as the settings you configure here. 4. Click to save and finish the settings. A reboot is required for the settings to take effect.
33 User Manual of Network Camera 5.3.6 Configuring 802.1X Settings Purpose: The IEEE 802.1X standard is supported by the network cameras, and when the feature is enabled, the camera data is secured and user authentication is needed when connecting the camera to the network protected by the IEEE 802.1X. Before you start: The authentication server must be configured. Please apply and register a user name and password for 802.1X in the server. Steps: 1. Enter the 802.
34 User Manual of Network Camera 1. Enter the QoS Settings interface: Configuration >Advanced Configuration > Network > QoS Figure 5‐15 QoS Settings 2. Configure the QoS settings, including video / audio DSCP, event / alarm DSCP and Management DSCP. The valid value range of the DSCP is 0‐63. The bigger the DSCP value is the higher the priority is. SCP refers to the Differentiated Service Code Point; and the DSCP value is used in the IP header to indicate the priority of the data. 3.
35 User Manual of Network Camera Figure 5‐16 FTP Settings 2. Configure the FTP settings; and the user name and password are required for login the FTP server. Directory: In the Directory Structure field, you can select the root directory, parent directory and child directory. When the parent directory is selected, you have the option to use the Device Name, Device Number or Device IP for the name of the directory; and when the Child Directory is selected, you can use the Camera Name or Camera No.
36 User Manual of Network Camera With the function enabled, you don’t need to configure the port mapping for each port, and the camera is connected to the Wide Area Network via the router. Steps: 1. Enter the UPnP™ settings interface. Configuration >Advanced Configuration > Network > UPnP 2. Check the checkbox to enable the UPnP™ function. The name of the device when detected online can be edited.
User Manual of Network Camera 37 1. Enter the Video Settings interface: Configuration >Basic Configuration > Video / Audio > Video Or Configuration > Advanced Configuration > Video / Audio > Video Figure 5‐19 Configure Video Settings 2. Select the Stream Type of the camera to main stream (normal), sub‐stream or third stream. The main stream is usually for recording and live viewing with good bandwidth, and the sub‐stream and third stream can be used for live viewing when the bandwidth is limited. 3.
38 User Manual of Network Camera standard can be set to H.264. When the Stream Type of the camera is sub‐stream, the Video Encoding standard can be set to H.264, MJPEG. I Frame Interval: Set the I‐Frame interval to 1~400. 4. Click to save the settings. 5.4.2 Configuring Audio Settings Steps: 1. Enter the Audio Settings interface Configuration > Basic Configuration > Video / Audio > Audio Or Configuration > Advanced Configuration > Video / Audio > Audio Figure 5‐20 Audio Settings 2.
39 User Manual of Network Camera Configuration > Basic Configuration> Image> Display Settings Or Configuration > Advanced Configuration> Image> Display Settings 2. Set the image parameters of the camera. Figure 5‐21 Display Settings Descriptions of parameter configuration Overexposure Prevention: Enable or disable the function in this field. Exposure Time: Value ranges from 1/25 to 1/100,000s. Adjust it according to the lightening condition. Iris Mode: Auto and Manual are selectable.
40 User Manual of Network Camera image horizontally and vertically. It can be used to view the image in the way you see it directly using your eyes. WDR: Wide dynamic range can be used when there is a high contrast of the bright area and the dark area of the scene. BLC Area: BLC area is the area sense the light intensity; Close, Up, Down, Left, Right and Center are selectable. White Balance: The below figure shows the white balance type selectable. You can choose it according to the real condition.
41 User Manual of Network Camera You can customize the camera name and time on the screen. Steps: 1. Enter the OSD Settings interface: Configuration > Advanced Configuration > Image > OSD Settings Figure 5‐23 OSD Settings 2. Check the corresponding checkbox to select the display of camera name, date or week if required. 3. Edit the camera name in the text field of Camera Name. 4. Select from the drop‐down list to set the time format, date format, display mode and the OSD font size. 5.
42 User Manual of Network Camera 5.5.3 Configuring Text Overlay Settings Purpose: You can customize the text overlay. Steps: 1. Enter the Text Overlay Settings interface: Configuration > Advanced Configuration > Image > Text Overlay 2. Check the checkbox in front of textbox to enable the on‐screen display. 3. Input the characters in the textbox. 4. Use the mouse to click and drag the red text frame in the live view window to adjust the text overlay position. 5. Click .
43 User Manual of Network Camera 2. Check the checkbox of Enable Privacy Mask to enable this function. 3. Click . Figure 5‐26 Privacy Mask Settings 4. Click and drag the mouse in the live video window to draw the mask area. You are allowed to draw up to 4 areas on the same image. 5. (Optional) click to clear all of the areas you set without saving them. 6. Click to save the settings. 5.
44 User Manual of Network Camera video for the motion occurred in the surveillance scene. Tasks: 1. Set the Motion Detection Area. Steps: (1) Enter the motion detection settings interface Configuration > Advanced Configuration> Events > Motion Detection (2) Check the checkbox of Enable Motion Detection. Figure 5‐27 Enable Motion Detection (3) Click . Click and drag the mouse on the live video image to draw a motion detection area. You can draw up to 8 motion detection areas on the same image.
45 User Manual of Network Camera Figure 5‐28 Arming Time (1) Click to edit the arming schedule. The Figure 5‐29 shows the editing interface of the arming schedule. (2) Choose the day you want to set the arming schedule. (3) Click to set the time period for the arming schedule. (4) After you set the arming schedule, you can copy the schedule to other days (Optional). (5) Click to save the settings. The time of each period can’t be overlapped. Up to 4 periods can be configured for each day.
46 User Manual of Network Camera 3. Set the Alarm Actions for Motion Detection. Purpose: You can specify the linkage method when an event occurs. The following contents are about how to configure the different types of linkage method. Figure 5‐30 Linkage Method Steps: (1) Check the checkbox to select the linkage method. Audible warning, notify surveillance center, send email, upload to FTP, trigger channel and trigger alarm output are selectable (Optional).
47 User Manual of Network Camera To trigger an alarm output when an event occurs, please refer to Section 5.6.4 to set the related parameters. 5.6.2 Configuring Tamper‐proof Alarm Purpose: You can configure the camera to trigger the alarm when the lens is covered and take alarm response action. Steps: 1. Enter the Tamper‐proof Settings interface: Configuration > Advanced Configuration > Events > Tamper‐proof Figure 5‐31 Tamper‐proof Alarm 2.
48 User Manual of Network Camera 5.6.1. 5. Check the checkbox to select the linkage method taken for the tamper‐proof. Audible warning, notify surveillance center, send email and trigger alarm output are selectable. Please refer to Step 3 Set the Alarm Actions for Motion Detection in Section 5.6.1. 6. Click to save the settings. 5.6.3 Configuring External Alarm Input Steps: 1. Enter the Alarm Input Settings interface: Configuration > Advanced Configuration> Events > Alarm Input: 2.
49 User Manual of Network Camera to Step 3 Set the Alarm Actions for Motion Detection in Section 5.6.1. 5. You can also choose the PTZ linking for the alarm input if your camera is installed with a pan/tilt unit. Check the relative checkbox and select the No. to enable Preset Calling, Patrol Calling or Pattern Calling. 6. You can copy your settings to other alarm inputs. 7. Click to save the settings. Figure 5‐33 Linkage Method 5.6.4 Configuring Alarm Output Steps: 1.
50 User Manual of Network Camera Figure 5‐34 Alarm Output Settings 5.6.5 Handling Exception The exception type can be HDD full, HDD error, network disconnected, IP address conflicted and illegal login to the cameras. Steps: 1. Enter the Exception Settings interface: Configuration > Advanced Configuration> Events > Exception 2. Check the checkbox to set the actions taken for the Exception alarm. Refer to Step 3 Set the Alarm Actions Taken for Motion Detection in Section 5.6.1.
51 User Manual of Network Camera 5.6.6 Email Sending Triggered by Alarm Purpose: The system can be configured to send an Email notification to all designated receivers if an alarm event is detected, e.g., motion detection event, video loss, tamper‐proof, etc. Before you start: Please configure the DNS Server settings under Basic Configuration > Network > TCP/IP or Advanced Configuration > Network > TCP/IP before using the Email function. Steps: 1.
52 User Manual of Network Camera Sender’s Address: The email address of the sender. SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25 (not secured). And the SSL SMTP port is 465. Enable SSL: Check the checkbox to enable SSL if it is required by the SMTP server. Attached Image: Check the checkbox of Attached Image if you want to send emails with attached alarm images.
53 User Manual of Network Camera 1) Configure the FTP settings and check checkbox in FTP Settings interface. Please refer to Section 5.3.8 Configuring FTP Settings for more details to configure FTP parameters. 2) Check the Enable Timing Snapshot checkbox. Upload event‐triggered snapshots to FTP Steps: 1) Configure the FTP settings and check checkbox in FTP Settings interface. Please refer to Section 5.3.8 Configuring FTP Settings for more details to configure FTP parameters.
54 User Manual of Network Camera Chapter 6 Storage Settings Before you start: To configure record settings, please make sure that you have the network storage device within the network or the SD card inserted in your camera. 6.1 Configuring NAS Settings Before you start: The network disk should be available within the network and properly configured to store the recorded files, log files, etc. Steps: 1.
55 User Manual of Network Camera type and property of the disk. Figure 6‐2 Initialize Disk (2) If the status of the disk is Uninitialized, check the corresponding checkbox to select the disk and click to start initializing the disk. Figure 6‐3 Initializing When the initialization completed, the status of disk will become Normal. Figure 6‐4 View Disk Status Up to 8 NAS disks can be connected to the camera.
56 User Manual of Network Camera Figure 6‐5 Recording Schedule Interface 2. Check the checkbox of Enable Record Schedule to enable scheduled recording. 3. Set the record parameters of the camera. Figure 6‐6 Record Parameters Pre‐record: The time you set to start recording before the scheduled time or the event. For example, if an alarm triggers recording at 10:00, and the pre‐record time is set as 5 seconds, the camera starts to record at 9:59:55.
57 User Manual of Network Camera Figure 6‐7 Record Schedule 5. Choose the day to set the record schedule. (1) Set all‐day record or segment record: If you want to configure the all‐day recording, please check the All Day checkbox. If you want to record in different time sections, check the Customize checkbox. Set the Start Time and End Time. The time of each segment can’t be overlapped. Up to 4 segments can be configured. (2) Select a Record Type.
58 User Manual of Network Camera If you select Alarm, the video will be recorded when the alarm is triggered via the external alarm input channels. Besides configuring the recording schedule, you have to set the Alarm Type and check the checkbox of Trigger Channel in the Linkage Method of Alarm Input Settings interface. For detailed information, please refer to Section 5.6.3.
59 User Manual of Network Camera Chapter 7 Playback Purpose: This section explains how to view the remotely recorded video files stored in the network disks or SD cards. Steps: 1. Click on the menu bar to enter playback interface. Figure 7‐1 Playback Interface 2. Select the date and click . Figure 7‐2 Search Video 3. Click to play the video files found on this date.
60 User Manual of Network Camera process. Figure 7‐3 Playback Toolbar Table 7‐1 Description of the buttons Button Operation Button Play Pause Stop / Capture a picture Start/Stop clipping video files Audio on and adjust volume/Mute / Speed down Download video files Speed up Playback by frame Operation / Download captured pictures Enable/Disable digital zoom You can choose the file paths locally for downloaded playback video files and pictures in Local Configuration interface.
61 User Manual of Network Camera Chapter 8 Log Searching Purpose: The operation, alarm, exception and information of the camera can be stored in log files. You can also export the log files on your demand. Before you start: Please configure network storage for the camera or insert a SD card in the camera. Steps: 1. Click on the menu bar to enter log searching interface. Figure 8‐1 Log Searching Interface 2.
62 User Manual of Network Camera Chapter 9 Others 9.1 Managing User Accounts Enter the User Management interface: Configuration >Basic Configuration> Security > User Or Configuration > Advanced Configuration> Security > User The admin user has access to create, modify or delete other accounts. Up to 15 user accounts can be created. Figure 9‐1 User Information Add a User Steps: 1. Click to add a user. 2. Input the new User Name, select Level and input Password.
63 User Manual of Network Camera Figure 9‐2 Add a User Modify a User Steps: 1. Left‐click to select the user from the list and click . 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions. 4. Click to finish the user modification.
64 User Manual of Network Camera Delete a User Steps: 1. Select the user you want to delete, and click 2. Click . when dialogue box pops up to confirm the operation. 9.2 Configuring RTSP Authentication Purpose: You can specifically secure the stream data of live view. Steps: 1. Enter the RTSP Authentication interface: Configuration> Advanced Configuration> Security > RTSP Authentication Figure 9‐4 RTSP Authentication 2.
65 User Manual of Network Camera 2. Set the Anonymous Visit permission Enable or Disable in the drop‐down list to enable or disable the anonymous visit. 3. Click to save the settings. There will be a checkbox of Anonymous by the next time you logging in. Figure 9‐6 Login Interface with an Anonymous Checkbox 4. Check the checkbox of Anonymous and click 9.4 IP Address Filter Purpose: This function makes it possible for access control. Steps: 1.
66 User Manual of Network Camera 3. Select the type of IP Address Filter in the drop‐down list, Forbidden and Allowed are selectable. 4. Set the IP Address Filter list. Add an IP Address Steps: (1) Click to add an IP. (2) Input the IP Adreess. Figure 9‐8 Add an IP (3) Click to finish adding. Modify an IP Address Steps: (1) Left‐click an IP address from filter list and click button. (2) Modigy the IP address in the text filed.
67 User Manual of Network Camera Configuration > Basic Configuration> System > Device Information Or Configuration > Advanced Configuration> System > Device Information In the Device Information interface, you can edit the Device Name. Other information of the network camera, such as Model, Serial No., Firmware Version, Encoding Version, Number of Channels, Number of HDDs, Number of Alarm Input and Number of Alarm Output are displayed. The information cannot be changed in this menu.
68 User Manual of Network Camera 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance or 2. Click to restore the default settings. Figure 9‐12 Restore Default Settings After restoring the default settings, the IP address is also restored to the default IP address, please be careful for this action. 9.6.
69 User Manual of Network Camera camera during the process. The camera reboots automatically after upgrading. Figure 9‐13 Remote Upgrade 9.7 RS‐232 Settings Purpose: The RS‐232 port can be used in two ways: Parameters Configuration: Connect a computer to the camera through the serial port. Device parameters can be configured by using software such as HyperTerminal. The serial port parameters must be the same as the serial port parameters of the camera.
70 User Manual of Network Camera Appendix Appendix 1 iVMS‐4200 Client Software Introduction iVMS‐4200 is a versatile video management software for the DVRs, NVRs, IP cameras, encoders, decoders, etc. It provides multiple functionalities, including real‐time live view, video recording, remote search and playback, file backup, etc., for the connected devices to meet the needs of monitoring task.
71 User Manual of Network Camera modify the network parameters. 2. Edit the modifiable network parameters, e.g. IP address and port number. 3. Enter the admin password in the Manager Password field and click save the changes. Figure A.1.2 Modify Network Parameters Restore default password Steps: 1. Select the device you want to restore the default password. 2. Click . 3. Input the security code got from the technical support from our company. 4. Click to restore the default password.
Appendix 2 Port Mapping The following settings are for TP‐LINK router (TL‐R410). The settings vary depending on different models of routers. Steps: 1. Select the WAN Connection Type, as shown below: Figure A.2.1 Select the WAN Connection Type 2. Set the LAN parameters of the router as in the following figure, including IP address and subnet mask settings. Figure A.2.2 Set the LAN parameters 3. Set the port mapping in the virtual severs of Forwarding. By default, camera uses port 80, 8000, 554 and 8200.
73 User Manual of Network Camera ports of another camera as 81, 8001, 555, 8201 with IP 192.168.1.24. Refer to the steps as below: The 8200 port changes with the 8000 port with a constant value of 200. E.g. if the 8000 port is changed to 8005, then the 8200 port should be changed to 8205. Steps: 1. As the settings mentioned above, map the port 80, 8000, 554 and 8200 for the network camera at 192.168.1.23 2. Map the port 81, 8001, 555 and 8201 for the network camera at 192.168.1.24. 3.
