Safety Instructions

8, The type of driven part the drive is intended for.
9 , WARNING: Important safety instructions. It is important
for the safety of persons to follow these instructions.
Save these instructions.
10, Do not allow children to play with fixed controls. Keep
remote controls away from children
11, Frequently examine the installation for imbalance and
signs of wear or damage to cables and springs. Do not
use if repair or adjustment is necessary
12, Watch the moving shutter and keep people away until
he shutter is completely closed
13, WARNING: Important safety instructions. Follow all
instructions, since incorrect installation can lead to
severe injury.
14, Before installing the drive, remove any unnecessary
cords and disable any equipment not needed for
powered operation
Motor external battery
Motor external battery interface
The charging interface
Product introduction
External switch interface
LED light Setting button
Motor forward line
Motor reverse line
Public line
1. Not operating under low voltage motors:
Motor stop running when the supply voltage is lower than 13.5V, LED light will flash 5 times, buzzer
beep 5 times,prompt low voltage to be charged
2. Operating：
①The valid interval of the emitter button is 10s,the emitter will quit the set after 10s;
②The LED flashes or beep for hint,please do the next step after the hint.
3. Set limit position：
①Every time you install the motor,first set after a curtain opened travel to work properly;
②After setting,with power and memory function,after each power cycle required to
open or close a recovery stroke;
③After replacing the track or cord to be removed for the trip,and then set itinerary.
4. When the motor running without any operation,the maximum running time is 4
minutes,it will stop automatically.
5. One motor maximum can store 10 channels,over 10 channels,if still need add new channels,
it will be repeating covered in turn from second channel.
6. If the emitter lost,please set up again with new emitter.
Functional features：
Stall Protection
Built-in Receiver
Manual Override
Switch Control
Program Button
Solar Charging
Electronic Limit
Switch Direction
Auto Limit Setting
Run/Stop by Pulling Fabric
Preferred Stop Position
Lithium Battery with Quick Plug
-5
55
Working
Temperature
Parameter (More models and parameters are subject to the nameplate)
Motor installation
The assembly of rubber belt for curtain motor
The comfirmation of
profiled material dimension
7cm
The cap length
Leave half teeth
The length of profiled material = The total
lenth of track - The cap length × 2
The total length of track is 2m
The length of profiled material: 200cm-14cm=186cm
Use the screw driver to
place the parts like the
gear into the lower cover
Refer the complete lower
cove in below picture
Thread the rubber belt
into thethe lower cover
Fix the cut rubber belt end
with the belt fasten button
Keep this end complete
Install the clip part like the referance picture
and insert the track into the lower cover
Slide the slip part to the other end to be flush with the
head rail.Cut the other end of rubber belt with 11.5cm left
The joint assembly of track
B
track
Track joint board
Track joint
bracket
The f0llowing steps pls refer to
“the assembly of rubber belt and track”
Insert the track joint bracket
for one end to the track joint
Fix the screws
Note: The track needs to be engrafted when
the length is less the required
The track needs to be engrafted when
inconvenient to transport
11.5cm
Insert the track
joint board into
the two ends of track
The marked position is in the
middle of the slip parts.Half of
the slip parts are in the head
rail as in the picture
Seperate the lower cover and the headrail with the
11.5cm belt remaining outside the headrail.Then fix
two fasten buttons on the same side of rubber belt
(it is to figure out the position of the other slip part.)
Leave one teeth
between these two
belt fasten button
Install the belt fasten button and
the slip part as in the picture
Install the belt facton button
and the slip part as in the picture
After one slip part installed,then thread the other
end of the belt through the other lower cover
These two slip parts is successfully installed
4
Folding method for joint track (for easy transit)
The installation method for curtain motor
5
4
3
5
4
3
Assemble the curtain motor
track at appropriate place,
then fix with screws
Check the position of
brackets,fix it at an
appropiate place on the track
Please check assembling is ok
Assemble the motor Finish assembling
The runner are installed
The hook
Place the hook and the upper cover into the track
Search for the sl-
ip part connected
with the ends of
the rubber belt
Take off the screw
of the slip parts
and the connection
bracket
Track folding method
The overlap arm
which is connected
to the two ends of
rubber belt
Pull the slip parts
slightly and seper-
ate the connection
part at the same
time
Push the connec-
tion parts to one
side
Fold the track
Unfold the
folded track
Combine the
track slowly
Push the con-
nection bracket
to the connec-
tion part
Restoring the track
Screw the co-
nnnection bra-
cket and install
the slip parts
The track is
successfully
assembled
The slip
parts
Slide the runners into the track
Operation note
Please read the following precautions before use:

READING
MT01-2101-069002
Type
1.2N.m
Rated Torque
(N.m)
80-120RPM
Rated speed
(
RPM
)
DC 15V
Rated Voltage
(V)
433.925MHz
Emission
Frequency(MHz)
Curtain Motor-
MT01-2101-069002
Specification
(A-01)