Safety Instructions

OPERATION GUIDE
Fault and solution
Note: Press the open button, if the curtain closed, please perform the reverse of direction setting;Only one emitter can
be saved without the limit.
Note: the method one needs to be carried out without a trip; When the change is successful, it will delete the settings
related to the limit and need to reset the limit.
Note: If the motor is short sound twice, it means the speed is already fast or slow; when there is no limit, the motor
defaults to low speed running. When there is limit, the motor will run fast by default.
Setting up is ok
LED flashes x5
“Di” x3
LED flashes x1
T<10s
2 Switch direction
3 Speed regulation
Long press 2s
Successful change the direction
LED flashes x5
“Di” x3
LED flashes x3
Long press 10s
Loosen button
Press 1s
Successful change the direction
LED flashes x5
“Di” x3
Method one
Method two

1, Acceleration setting
LED flashes x1
“Di” x1
LED flashes x5
“Di~” x1
LED flashes x1
“Di” x1
LED flashes x1
“Di” x1
LED flashes x5
“Di~” x1
LED flashes x1
“Di” x1
Motor speed increases
Press 1s
3
Press 1s Press 1s
Press 1s Press 1s Press 1s
2, Deceleration setting
Motor speed is reduced
3
“Di” x1
“Di” x3
4 Limit position setting
Limit is ok
LED flashes x5
“Di” x3
1, Set the limit
LED flashes x1
“Di” x1
LED flashes x5
“Di” x3
LED flashes x1
“Di” x1
LED flashes x1
“Di” x1
LED flashes x5
“Di” x3
LED flashes x1
“Di” x1
Note: After the limit is set, the motor enters the user mode; after the limit is deleted, the motor enters the factory mode.
2, Cancel the limit
Cancel the limit is ok
3 3
3
User mode
1 Preferred stop position
Preferred
stop posi-
tion is ok
Run to the re-
quired preferr-
ed stop position
After the up limit and down limit setting, you can set preferred stop position between them as the half open position
1, Set preferred stop position
3, Cancel preferred stop position
The motor moves to preferred stop position automatically
Long
press 2s
2, Run to preferred stop position
3
Cancel preferred stop position is ok
Slow flash x1
“Di~” x1
1, Fine-tuning open limit position
2, Fine-tuning close limit position
2 Fine-tuning open/close limit position
Slow flash x1
“Di~” x1
Long
press 5s
LED flashes x5
“Di” x3
Slow flash x1
“Di~” x1
LED flashes x5
“Di” x3
Open limit
fine-tuning
success
Note: after entering fine-tuning limit mode, if not confirm new schedule points within 2 minutes, or press P1 button
or emitter setting button automatically quit this pattern, limit position remains unchanged.
Enter the
fine-tuning
limit mode

Long press 2s
Long
press 5s
Long press 2s

Close limit
fine-tuning
success
Enter the
fine-tuning
limit mode
 
Press open/close button or
hand pull the curtain adjust
the new close limit position
or
3 Add/delete emitter
3 3
3
Add emitter is ok
4 Weak electric switch mode selection
3
LED flashes x1
“Di” x1
Set up is ok
1, Double-button reboundable switch mode(The factory default weak electric switch mode)
LED flashes x3
LED flashes x5
“Di” x3“Di”x3
3, Single-button cyclic switch mode
3
2, DC246 switch mode
3
Set up is ok
Set up is ok
5 Run/stop by pulling fabric
Note: repeat this operation can run by pulling fabric;The default is run by pulling fabric.
Stop by pulling fabric
LED flashes x5
“Di” x3
6 The search function
Note: this operation needs to be done without the motor to the code or the motor to the search emitter;Emitter after
entering search pattern, if received equipment emitter LED lights flashing, motor run continuously for 2 minutes, not
received the emitter exit search instructions, the motor will exit the search pattern.
The emitter
enters the
search mode
Search to match motor, motor cycle
point moving operation
LED cycle
flashing
Press 1s
3
+
7 Reset to factory mode
Reset to factory mode successfully
LED flashes x8
“Di” x4
Button specification
1 Setting up
Factory mode
Long press 2sLoosen buttonLong press 2s
The curtain was opened and
the obstruction stopped
The curtains were
closed and stopped
Press 1sPress 1s
Press 1s Press 1s Press 1s
LED flashes x1
“Di” x1
LED flashes x5
“Di” x3
LED flashes x1
“Di” x1
Press 1s Press 1s Press 1s
LED flashes x1
“Di” x1
LED flashes x1
“Di” x1
Press 1s Press 1s Press 1s
Press 1s Press 1sPress 1s
Press x1Long
press 10s
Long press 2sLoosen button
or
Press open/close button or
hand pull the curtain adjust
the new open limit position
Note: Emitter is the one already matched code, while emitter has not;Repeat this to remove the newly added emitter.
Press x2Long
press 10s
Long press 2sLoosen button
Press x3Long
press 10s
Long press 2sLoosen button
Press x1Long
press 10s
Loosen button
Long
press 14s
Loosen button
LED flashes x2
“Di” x2LED flashes x3
LED flashes x5
“Di” x3“Di”x3
LED flashes x3
“Di” x3LED flashes x3
LED flashes x5
“Di” x3“Di”x3
LED flashes x3 “Di”x3
COMMON FAULTS PROCESSING METHODNUMBER
1
The motor is
not running
Check the power supply
2
Unable to control
remote controller
1, Check the emitter for the code;2, Replace the emitter battery
3
Remote control
on the contrary
Implement the reverse of direction setting
5
External switch
on the contrary
Replacement switches line order
4
External switch
is out of control
Check the external switch motor cable is intact
6 Cannot close
1, Check emitter's open button to ensure if it works with open function,
if not,please change direction firstly;2, check limit position;
7
Always hit or couldn
not get to the edge
Cancel the limit,setting again
8
With the hand to
pull,feeling stuck
Set the limit of the trip
9
Encounter obstacles
will not stop
Check the screw used to fixed orbital
MT01-2101-069002
Specification
(A-01)
P
2
M
P
2
Lithiu
m
Cell
3
V
P
2
Up button
Stop button
Down button
Setting button